Service tutorial Ender -3 Heating Troubleshooting
ฝัง
- เผยแพร่เมื่อ 2 ก.ย. 2021
- Accessories purchase, Please contact our official email or website, remember to attach your machine type and accessories pictures
Official email：info@creality.com
Official website: www.creality.com
Any technical support in need, Please contact our official service email，remember to attach your printer model、complete orderscreenshot、purchase link 、printer product SN and the issue relevant video or picture .
Official service email：cs@creality.com
Any inquiry of firmware and software，Please download it by creality official website：www.creality.com/download
Creality firmware obtaining tutorial： • Video - วิทยาศาสตร์และเทคโนโลยี
this company actually sucks. i just got my 2nd one cuz first one had this problem and a screw hole was miss placed. now the one i got everytime i start a print it does this. it was meant to be built out of the box and not tinker with the internals. idk why every creality printer has done this and people keep buying from them.
i upgraded to new merlin and since then i get error
I upgraded to the Max Neo because I had such a good experience with the Pro. But, after about 10 hours of printing, the CPU froze up and I got an alarm. I did the test in the video and the motherboard was bad. Took me three months to get a replacement. THEN the replacement was bad right out of the box with the same problem!!! Two months after that I’m still trying to return the second piece of junk. What a mess.
My extruder and bed heat up fine but just won't initiate printing, any advice? Thanks
All test results say the 3d printer is in working order - still having problems, what’s the next step?
Hi while o check the voltage the multimeter show 0v
So do i need to change the motherboard
I have upgraded my Ender 3 pro with a 4.2.7 motherboard. I also have resoldered the wires to the DC fan on the Swiss and noe whole printer shuts off and then turns on and back to the info screen every time the heater to the nozzle activates. The heater to the bed works but the heater to the nozzle acts up and shuts down the printer just for it to turn on right back where started. I am hoping to find an answer from creality soon as possible or any body who knows how this happens.
No expert but it sounds like there might be a short if sending power to the nozzle causes the printer to restart. You might want to check and make sure there is not a stray wire from the nozzle heater sticking out and making contact with another wire or even the board. You could follow the same troubleshooting steps here and swap the heater wires from the nozzle and bed to see if that solves the issue when heating the nozzle and if it then starts happening when you heat the bed.
If it still happens when you heat up the nozzle next step would be to check your hotend wires at the hotend itself to see if something some wire is crossed or touching something else.
FYI, Creality is a garbage company.
Falta de compromisso com o consumidor, estou com duas maquinas com a placa 4.2.2 com o chip GD, desde agosto de 2023, problemas de travamentos, nao é possivel atualizar o marlin, nao tem como usar devido aos erros thermal, realmente so acionando judicialmente.
Do you have to set your temp that high?
No I have mine at 220 and it works perfectly fine
@@The_best_bass_fisher What's Causing this issue its really pissing me off my printer was working just fine now the hot end wont heat pass 218 degrees and starts to lose heat and starts making a horrible buzzing noise
@@blueanon8021 it should look like a wire with a tiny little bulb of a light, and then you can search up videos on how to replace it’s fairly easy
@@The_best_bass_fisher so it's not the hot end thermo?
@@blueanon8021 it’s the thermostat that you’re having a problem with. I will link a video at the end of this comment and it also in the video of that is linked it will show you how to repair it and it has a link on where to buy th-cam.com/video/pnvcAumZOug/w-d-xo.html