Anycubic Kobra Max General maintenance Advice
ฝัง
- เผยแพร่เมื่อ 10 พ.ย. 2022
- Anycubic Kobra Max General maintenance Advice
I would always suggest carrying out a routine maintenance of your printer.
checking tension belts
z rods
bolts
electric components
and eccentric nuts
New nozzle assembly.
amzn.to/3Gc658i
Spare volcano nozzles
amzn.to/3TxMhz4
prevention is better than cure
#anycubic
#3dprinting
#3dpuk - วิทยาศาสตร์และเทคโนโลยี
Right on brother. Its been awhile. hope all is well. now that I have my live stream up and running I just clued in that I needed to do a bit of maintenance work on the kobra. Still my favorite. Your video was the first one to pop up and you have made my prints that much better. I thank you so much. I'll be posting some work soon and I will definitely name drop you in the videos. Thanks again
As usual, an excellent video, super useful to remind us all these maintenance points - I tend to forget too many of them too often... Thank you !!
Thank you, sir.
Thanks for another great tutorial :D
Thank you
Thanks for the good video 3DPUK. For future messages regarding various issues; I contacted the Anycubic after sales department and those guys are really helpful (No I don't work for them :) ). I got some bed level sensor issue and so far they sent me a new probe, a new printhead board & cable and a new motherboard... Haven't tried the new motherboard yet so my issue is still there but I'm confident.
I also use the Sunlu dryer as my dispenser.
Now I noticed you tied the printhead cable to the structure rod on the side, any other cable routing advice ?
Hi, I receantly bought this printer, installed a flexible print plate, connected it to octoprint and ran a bed visualizer. I found out, that the bed is significantly lower in the middle refered to corners.
I looked at the mounting and there are two srews with springs but no nuts, adjusting wheels nothing. I think that the bed is sagging in the middle which causes my issue.
Can someone help me with this?
Thanks
Hey i need help trouble shooting the thing doesnt wanna move across the x axis even when i push it by hand. I cant tell if its a belt issue or motor issue
We are waiting for the video now. how to set the optimal temperature for 1 specific plastic, according to the melting temperature, then the filament feed rate or printing speed, as well as setting accelerations at the printing corners. -for optimal performance in terms of printing speed, with minimal loss of quality. it is clear that plastics are different and in different batches have different melting points and different fluidity. And also a video about resuming printing after an error on cobra max.
I Will try and create one for these items very soon
You should add in gantry leveling since this only has one side z stop. It's caused me to have several issues. Would also like a way to reach out to you
Ping me on my Facebook group 3DPUK TECH channel I can support there
Have you used a .8mm nozzle yet? If so what speed have you printed at and what accel?
I haven't changed from stock yet
Please need help. I bought one of these printers for my son, we noticed that the bed is not heating up. And I notice that there is an air bobble in the middle of the button part of the printer bed. I'll appreciate any advice. Thank you.
Would it be possible to join my Facebook group 3DPUK TECH CHANNEL we can discuss there
Hey dude, my middle roller wheel under the left hand side of the bed spins freely. The other two wheels are fine but the middle one no matter how i adjust it just rolls free so is there for nothing. That the case with you?
Hey no all mine are equal tension
.. i would suggest loosening them all and make sure it's square front and make.. and then tightness each one gently and ensure equal tensions
So I don't know if anyone can help me answer this, I have a Kobra Max and I am getting a crazy amount of Stringing. I have changed the retraction form 0-7.0mm and nothing got better. I used a temp tower and each one looked terrible. I don't know what to do, all I find is snark from ppl on Discord. Any assistance would be appreciated. Help please.
Hey sorry that the community isn't supporting you, have you found this to.be on different types of filament ?? Or is this with 1 in particular, I sometimes find stringing can also be to do with wet filament, if it's not that and you can confirm it's been dried then, it could also be to do with speed of printing I always try around 50mm/s - 4 retraction ..
My filament sensor keeps detecting, falsely, that my filament has run out. I hit the button and everything resumes just fine until a random amount of time passes and it repeats the error
Sounds like a failed filament sensor, maybe try the following 🤔 bypass filament sensor and go direct into bowden extruder and place a snipping of filament into the sensor so it reads as engaged. It won't allow too print without this... its a shame the firmware doesn't allow for turning the filament runout sensor off 😢 thanks for watching and don't forget to like and subscribe 😉 if not already done so
I had to flip the bed because it was sticking too good
Is there anyway you can email me? I have exhausted so many avenue of how my cobra max is printing wrong, I am not sure about the print nozzle and not working
I've messaged you on Instagram