2000 - 2006 Chevy Silverado Remote Key Fob Programming - How To Pair Program Chevrolet Fob

A DIY video tutorial on how to program or pair a remote key fob to a 2000 - 2006 Chevy Silverado. You will need an ignition key and all of the key fob remotes you want programmed to the Chevrolet Silverado in order to complete this programming procedure.
To program or pair a remote key fob to your Chevy Silverado:
1. Close all vehicle doors.
2. Insert the key into the ignition.
3. Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.
4. Perform steps 5 through 8 in fairly rapid succession.
5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).
6. Turn the ignition switch to the OFF position.
7. Turn the ignition switch to the ON position.
8. Turn the ignition switch to the OFF position.
9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
10. Hold down the LOCK and UNLOCK buttons on the remote key fob simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
11. Repeat step 10 NOW for each additional remote key fob (including any existing fobs).
12. Turn the ignition switch to the ON position in order to exit the remote programming mode.
This programming or pairing procedure applies to the following models of Chevrolet Silverado:
2000 Chevy Silverado
2001 Chevy Silverado
2002 Chevy Silverado
2003 Chevy Silverado
2004 Chevy Silverado
2005 Chevy Silverado
2006Chevy Silverado
DIY keyless entry remote fob and smart key programming instructions available at www.ProgramYourRemote.com/
DIY Ignition key programming procedures available at www.ProgramAutoKeys.com/
Find a Locksmith in your area with www.LocateALocksmith.com

[@FunGuyWoodCreations]

2003 Silverado…worked like a dream. Thanks for the video

[@PYR-Auto]

You're welcome! Glad it helped

[@jasonv4806]

Thank you for this. I bought two fobs that came with a "go to link for instructions" that didn't exist. Your instructions were clear, concise and true. Thanks so much!!!

[@PYR-Auto]

You're welcome! Glad it helped

[@elizabethconcholar8597]

Concise instructions, very helpful. I had two remotes, I bought two additional remotes only took a few minutes to have them all programmed to the truck, thank you so much for the video.

[@PYR-Auto]

You're Welcome! Glad it helped

[@donnaswanson42]

I watched another video that said to open and close the door and then turn the key on after you do the first steps
I did that and it worked.

[@jesusmiranda3218]

Can’t believe spend $20 on new remote controls is working tks I appreciate

[@PYR-Auto]

Glad it helped!

[@bruceh1628]

Just did this on a 2005 Silverado,worked like a charm.Thank you

[@PYR-Auto]

You're Welcome!

[@patrickwilt3125]

Thank you so much this worked first time, just bought my duramax and now have 2 working remote for $20 dollars!

[@PYR-Auto]

You're Welcome! Glad it helped

[@NG-pf6cd]

Very easy and it worked. I paid 7$ for the one I programmed to my 2004 Chevy 1500

[@PYR-Auto]

Glad it helped!

[@TheBenoitProductions]

Old fab stopped working and this fixed it perfectly fine. Thank you for sharing, you are awesome 👌

[@PYR-Auto]

You're Welcome! Glad it helped

[@joelhernandez-ry4er]

You saved me a lot of work and frustration. Thanks a lot

[@PYR-Auto]

You're Welcome!

[@enochix3502]

Wow, very easy and straight forward. Thank you!

[@PYR-Auto]

You're Welcome!

[@karenhenson6825]

Thank you so much! Your directions made it so easy for me to follow. Success!

[@PYR-Auto]

You're Welcome! Glad it helped

[@tacptaco1]

Took three tries but it finally worked. THANKS!!!!!

[@PYR-Auto]

You're Welcome!

[@royrowell1166]

I just bought my fob from autozone and I’ve tried it like 5 different times and I can’t get it to work

[@jamespueschner4644]

Worked perfectly! Mega thanks!!!

[@PYR-Auto]

You're welcome!

[@Bama1963]

Thanks, worked perfectly for my 2005 Silverado

[@PYR-Auto]

You're Welcome!

[@schizzultz]

Thanks for the video! Got new fobs for my 2002 Chev 2500. Worked great!

[@PYR-Auto]

You're welcome!

[@2coldproductions896]

Most simple video ever perfect instruction very satisfied

[@PYR-Auto]

Thanks!

[@wayneblanchard3845]

Perfect! Fixed Both! Thanks soo much!

[@PYR-Auto]

You're Welcome!

[@kevinjuarezhernandez4970]

Dont you just love older cars otherwise this would have been $800 to $2000 for a stupid key fob on modern cars

[@RenZoLamas111]

Absolutely kevin

[@james1233666]

Well, this work, even if the check engine light is on

[@fiveninegarage]

@@james1233666yes

[@TheRebelYell73]

Worked like a charm on my 2004 Silverado. Thanks for the info!!

[@PYR-Auto]

You're Welcome! Glad it helped

[@DWalsh-ws2xs]

Great job explaining how to program my fob, THANK YOU :) 😃

[@PYR-Auto]

You're Welcome!

[@rickshaffer3822]

Perfect for my 2007 Silverado HD Classic

[@kameronday7645]

Awesome, thanks for the video!!! Worked perfectly on my 2000 silverado 1500

[@PYR-Auto]

You're welcome!

[@jasonyoung9559]

Perfect Instructions! Have 2 working FOBS for $25. No more fumbling for my keys in the dark to unlock my Silverado.

[@PYR-Auto]

Glad it helped!

[@colejones113]

Thanks for the simple and easy to understand instructions!! Got some new fobs for my 04 suburban, and it worked great.

[@PYR-Auto]

You're Welcome! Glad it helped

[@Jonnydeerhunter]

Thank you sir! Clear and Concise!

[@PYR-Auto]

You're Welcome! Glad it helped

[@bigheadsgarage]

Worked perfectly on a 2005 hummer h2. Thank you

[@PYR-Auto]

Nice! You're Welcome!

[@rickjames302]

Thank you very much for the helpful tutorial.

[@PYR-Auto]

You're Welcome!

[@coreyobaugh5709]

Thanks bro I appreciate the tutorial it’s working now

[@PYR-Auto]

You're Welcome!

[@joelstevensz06]

Great quick video tutorial

[@PYR-Auto]

Thanks!

[@rhannon86]

Thank you for the video. Worked perfectly

[@PYR-Auto]

You're Welcome!

[@vanmann8347]

Thanks! Worked like a charm.👍👍👍

[@PYR-Auto]

You're welcome! Glad it helped

[@joez.9932]

You’re the man!!! Thanks buddy 🤙🏻

[@PYR-Auto]

You're Welcome! Glad it helped

[@marcosrincon649]

Got it…
Piece of cake, thank you very much.

[@PYR-Auto]

You're Welcome!

[@Theyooperstone]

Thank you this work and it was very helpful and easy to do

[@PYR-Auto]

You're Welcome!

[@onetallguy19]

Thanks for the video. That was too easy. Too easy.

[@PYR-Auto]

You're Welcome!

[@spokentoexistence9060]

Great vid‼ Well explained 👍🏽

[@PYR-Auto]

Thanks!

[@Juanm9500]

It worked for me, thank you!!

[@PYR-Auto]

You're welcome!

[@AbuSattam.com.]

Thank you, much appreciated, worked with my escalade 2005

[@PYR-Auto]

You're Welcome!

[@efrainesparza7844]

Thank a lot. This work great

[@sixdouble]

Thanks so much. I did for my car and working perfect.

[@PYR-Auto]

You're Welcome!

[@RoomygotAutumn]

Badass video thank you!!

[@PYR-Auto]

You're Welcome!

[@acemeriel]

thanks for this amazing video.

[@PYR-Auto]

You're welcome!

[@itsnoteasy3520]

Thank you brother for your help

[@PYR-Auto]

You're Welcome!

[@milesblackard419]

Thanks worked great. Thank you

[@PYR-Auto]

You're Welcome!

[@gabogabrich]

thank you very much your video helped me

[@PYR-Auto]

You're Welcome!

[@eliesqueda3116]

Awesome video thanks

[@PYR-Auto]

You're Welcome!

[@mcnielentertainment]

Greatly appreciate this.

[@PYR-Auto]

Glad it helped!

[@la_gallada_ruiz9818]

Thanks bro I really appreciate it 👍

[@PYR-Auto]

You're Welcome!

[@dsgaragedavid1987]

Thanks very helpful

[@PYR-Auto]

You're Welcome! Glad it helped

[@witchypoo13]

Thank you so much!!!!!!!

[@PYR-Auto]

You're Welcome!

[@communism_sucks]

Thanks, just completed this. Easy quick to the point video.

[@PYR-Auto]

You're Welcome! Glad it helped

[@henryaguero2935]

Thank you

[@PYR-Auto]

You're Welcome!

[@gr8gmblr]

Thank you sir!

[@PYR-Auto]

You're Welcome!

[@margaretmechinus3732]

My 2000 Chevy 1500 pickup is on it's 3 set of fobs, unfortunately remembering how to program the new fobs did not work and the instructions from the manual that came with the truck does not work. The DIY video worked - it was perfect. Thanks

[@PYR-Auto]

You're Welcome! Glad it helped

[@waynefoulds1973]

easy thanks to you

[@PYR-Auto]

Glad it helped

[@lifeisgoodwilliams7520]

Thanks real eazy

[@PYR-Auto]

You’re Welcome!

[@chevrolet355]

Thank you. You saved me money from having to go to the dealership

[@PYR-Auto]

You're Welcome!

[@anc-absolutelynotcertified3421]

Very good

[@PYR-Auto]

Thanks!

[@bassassin2695]

Ultimate cheat code

[@Bowhunters6go8xz6x]

I had one of my original fobs that came with my truck when new that lost its programing on my GMC Sierra. The fob battery got so weak it would not lock or unlock the doors and the emergency (RED) button did not work. I replaced the battery with a new one but the fob still did not work so I got in the truck and ran through these steps and with the same new battery the fob started working again. Thanks !

[@jhonyramirez9065]

Gracias 👍👍👍

[@PYR-Auto]

You're Welcome!

[@tfreeb7353]

Thanks! I was missing the step to do the old and new at the same time. Now I know where I went wrong. :)

[@PYR-Auto]

Glad it helped

[@satanikhispanik]

I have a 2006 Silverado duramax that I bought used. How do I know if I can use remote access?

[@victherapper]

I have an 02 Silverado and it’s not working for some reason?

[@elimixon0128]

W mans

[@BackwoodStacks]

I tried this for my tbss it didn’t work wat would u recommend

[@KDuboutdoors19]

I have key fobs left from vehicles that I've junked. Will this work for a used fob as well as a new one?

[@PYR-Auto]

yes, as long as you are using the correct used fob

[@yancyhammondjr]

I have a 2000 Chevy Silverado 1500 LS. When I press the unlock and lock on driver side door it doesn't unlock or lock the passenger side door. What do you think that might be?

[@justindeckard5296]

how did you fix it?

[@jefrebugni4064]

Do you have to have the old fob to do the first cycle like you did here? I had one working fob for my truck, and it quit working. I tried a new battery and it did not fix it. So as of now, I have no fob.

[@PYR-Auto]

no - you do not need the old fob

[@utopia4160]

Will this procedure program my 2016 GMC SIERRA

[@PYR-Auto]

no

[@tonyprimiano9117]

This procedure didn't work for me with a new remote what do I do now?

[@tayk6815]

Where did you get the extra key fob and what dose it mean when your unlock button don’t work but your lock one does

[@PYR-Auto]

This was an old key fob that we already had. The button pads can wear out over time and some buttons may stop working - I would try replacing the button pad - replacements can be found online.

[@ruby_z71]

My original fob will lock the doors but not unlock them now. Does anybody know why that could be?

[@vincecrocker6209]

I did this with my trailblazer and the first one was successful but he second never cycled the door locks and wasn't programmed. Any advice?

[@PYR-Auto]

it sounds like there may be just be an issue with the second remote

[@58fenderdeluxe]

Will this also work for a 2005 Chevy Express Van ? Thank you!

[@PYR-Auto]

No - unfortunately there is no manual way to program fobs to a 2005 Express. You will need an automotive locksmith or dealership

[@xunikarielx]

Hello
Try to follow the procedure but as soon as I hit the ignition two times and release the open button, few seconds later, mine gets out of the programming time by honking two times

[@hebeb394]

Mine does this as well. Did you ever figure it out?

[@heatherbellamy6778]

Will this process also delete all previously programmed fobs? I had one stolen and want to delete it from my system if possible.

[@PYR-Auto]

Yes it will

[@intimidator4x4]

My drivers switch doesn’t work

[@TheSleepingonit]

Thank you much I had to replace my key fob after the keys were stolen

[@PYR-Auto]

You're Welcome! Glad it helped

[@bryansanchez1854]

This might be a dumb question but can this work if you have an aftermarket alarm system?

[@PYR-Auto]

it can still work but depending on the alarm system it may cause issues as well

[@SkateYoungNReckless]

I was able to program my key, tested it sitting inside but as soon as I get out it won’t work

[@MrKnacker74]

Thanks for the help! After reprogramming the remote the door locks work again but not the start function. All that happens when I push the start button is the exterior lights flash 5 times. Any idea on how to get the start function to work again?

[@PYR-Auto]

Im not sure what you mean when you say you are pressing the start button - these years of Silverado did not have push button start

[@MrKnacker74]

@@PYR-Auto It is an aftermarket remote start unit (Polar Start). I have found that either I can program my fob via flashing the hood pin or by pushing unlock button, brake, ignition, ect.. Anyhow, I resolved the issue. I hadn't programmed the Tach, once this was done I could remote start. Now what I can't figure out is how to enable the Cold Weather Mode. I did find the manual and it says to press and hold the shift button, then press and hold the start/stop button for 3 secs. The parking lights will flash 3 times (FYI, the supplied remote is a 5 button). I've tried this several times either by pressing the buttons in succession or consecutively and nothing happens. I don't expect you to know this, but just throwing it out there,

[@PYR-Auto]

For sure - glad you got it figured out

[@aaronraymond6243]

When I try this my horn honks and the key fob does nothing please help

[@garrycoleman2494]

When I bought the truck it didn't have a key fob so can I buy one and program it without having the original fob?

[@PYR-Auto]

Yes - as long as the vehicle has the factory remote option

[@dillonhiggins6443]

I don't have power switch locks how do I program.

[@PYR-Auto]

if you do not have electric locks then you will not have the factory remote option

[@TheKentleuk]

Just purchased 06 tahoe, keys came with no key fob. Can I still program a couple new ones?

[@PYR-Auto]

yes

[@806luis_9]

Mine don’t have unlock or unlock

[@charliedanoele]

HELP...Sync to my door locks but not to my alarm any suggestions..

[@charliedanoele]

2002 Silverado 1500 hd

[@smh5738]

What if you don’t already have a key fob? Since you have to have 2 for it to work?

[@PYR-Auto]

You don't need existing fobs for this to work - as long as the vehicle has the factory remote option

[@jacintogonzalez7146]

Can I program only one fob even if I have a original key fob??

[@PYR-Auto]

Yes

[@caitlyngill1788]

What if my existing key fob doesn’t work?

[@Juniorwest7]

Is it possible to program two ??

[@PYR-Auto]

yes - if you look at the steps in the description box of the video - you need to repeat step 10 for each additional remote

[@candelariolopez355]

Did you have idea how to program a control for 2007 colorado

[@PYR-Auto]

a 2007 Colorado key fob is not manually programmable - you will need an automotive locksmith or dealership

[@ZoArellano]

My Silverado does the cycle twice not once and won’t program. It’ll unlock and lock twice one I release the unlock bottom

[@richardcastillo4353]

I have a Chevrolet Captiva Sport 2013

[@fazejuice6098]

mine i do it but like right after i put it in the cycle it immediately cycles again after and it doesnt program the key

[@NG-pf6cd]

I had to do it 3x then it worked. Keep trying.

[@TheBambam281]

Will it work on a 2020

[@PYR-Auto]

no

[@williamdolder5856]

How can I do it without the push button lock ?

[@PYR-Auto]

if you do not have power locks then the vehicle will not have the factory remote option installed

[@Buck.B1]

Can this mess with the VATS?

[@PYR-Auto]

no

[@ForzaRT]

Why my key fob in 2006 Silverado is not working when is next to another Chevy car