I got a 49 Plymouth on trade and it needed everything. I learned how to rebuild nearly everything on it and drove it to a car show. I can still hear that old flathead go. Thank you for the memories ❤️
I love those old Chrysler flathead engines, really enjoyed seeing your come back to life. You put a lot of good common sense in your videos. I've owned a 1948 Dodge Sedan Suicide doors since 1964, my Dad bought it from the original owner. It's always been garaged and has 39,000 miles on it now. I'd not had it started since 1993 but my 50th High School Reunion is this year so I want to drive it to the reunion. A new six volt battery, cleaning the points and some fresh gas and she's running again as of last week. Got to rebuild the brakes and put on a new muffler and tires and we're close to heading out again. I'm keeping it totally stock as much as I can.
I’m reminded how simple cars used to be. A few tools and a couple of parts and you can make them run. Try doing that with today’s complicated cars. I miss the old days.
Anyone old enough to even know what a flathead engine is will at least know the basics in starting an engine that has sat for years and have their own way of doing things. I think he did a good job and I feel certain he did a lot BEFORE he started filming. And yes, the old Chrysler products and some other 6 volts (Packard, Hudson) systems were negative ground, but you don't negative ground 12 volts. I am 77 years old and still working on the old iron and have my way also. I like to blow the engine off with compressed air, check the oil, pull the plugs, squirt a little 10w motor oil in the cylinders and then attempt to rotate the engine back and forth and then see if she turns complete 360 degrees. If all looks good, pop the distributor cap, check for spark at the points, replace the plugs, rig up a temporary gas supply, and start the engine and let her idle, and speed her up gradually and check the oil pressure. And yes, these old engines will run for SHORT periods without water. The man does know what he's doing. As one reply stated, all of these old makes and models had fairly low compression, 6.5 to 7.5 and and if the engine cranks, and has at least minimum compression, fuel and spark, she will run. To be honest, I look under the hood of any late model and new vehicle, I don't have a clue as to what the hell I am even looking at. And I will NOT ride in any vehicle where the doors lock when you drive off. I'm always glad to see other folks save the old iron and keep these vintage cars/trucks from the crusher. Good video.
I had a 50 model Dodge in 65 it was bought at a service station for $25. It was wrecked on front end only had 32k miles on it. It had three speed with a fluid drive clutch. I drove it all over place!
The ground polarity matters little with old cars with no electronics, in theory the primary of the ignition coil should be reversed but it does not make a huge difference. As for not riding in a vehicle where the doors lock when you move, it depends where you live, on my own car it is an option they call "anti-hijack" I prefer to have the doors locked when I am driving slowly in the city. It also arguably makes the doors less likely to pop open in a roll-over. I love old cars but one thing they are universally lacking in is safety.
@@waltersmart1824 I had a '50 Dodge Wayfarer, "Fluid Drive" myself. Gor it in '64 from my brother-in-law for "get it running and its yours" deal. All it needed was a 6 volt battery and some fresh gas. Like yours, it had been wrecked, missing the right half of the grill, lower half of the right fender around to the passenger door. My fried called it the "black bomb". She would hold 70 MPH all day long. I kept her on the road until it was burning as much oil as it was gas. That fliud clutch was great on dates, since I din't _have_ to start off on low gear. Even started in third many times with no problems. It wasn't much on the drag strip :D !
@@g0fvt Any magnetic gages would be reversed, as would heater fan motors. We used to joke that the light bulbs would work backwards and if you turned them on with reversed polarity, they'd make everything darker.
I always like watching you getting old engines to run. Just need to have a spark and fuel and a decent battery and you always seem to get a so called impossible engine to start. Thanks for sharing
Peter Bloggs You ain’t wrong but you’d be surprised at how resilient old parts are. By the way he did say he found a government surplus crate motor for this car for $250 so why not fire up this old boat anchor?
Had a '46 Plymouth 4-door sedan I got started this way. Bought it in '74 for $50! Like this car, it sat for several years. after getting it started my buddies and I drove it all summer long. Good times indeed!
gotta love it. That's the first car I can remember ever being in. My dad had one when I was just a small fry. no back seat, I could play with my toys back there. It got turned into a race car, and my mom ran it in a powder puff derby. She won, too, not that the car was so great, but she could really drive.
My Father in law had a Wayfarer and it was really clean just needed an engine overhaul. They use to put those old 3 1/4 Bores in everything. I worked on a lot of them that were in forklifts and such. Unfortunately he ended up with some health issues and decided to get rid of it. I really wish I could have helped him fix it up but was having trouble with his eyes and didn't think he would ever be able to drive it. These are cool old cars!
My old man used to own a '49 Dodge Tudor. It threw a rod while we were on vacation in '58 and he had a new engine put in. What a fun trip, or maybe not.
The piston-strokes on many Dodges, Chrysler, and (later) Plymouth flathead sixes were VERY long. Great for hacking around town, but a big strain on a long highway trip. Not the least bit surprising you would throw a rod. Keep highway speeds down, or get overdrive.
Dang! Been searching old Dodge videos to help with my 52 Business Coupe. This one definitely did Watched this video a dozen times and just realized at the beginning of the video you had your battery hooked up backwards. Wish you would have mentioned that, it might have saved me hours. I never even thought of a positive ground system.
Hey Jonathan , hey from Canada! Really enjoying your videos, can't wait to see more. I gotta say you are truly creative , you are building true down to earth Rat Rods. I know when you are referring to " junk" you really mean treasures . Where I am , just trying to find anything like a Chevy six cylinder is like finding hens teeth. I realize trying to work and to do videos at the same time is difficult, but keep it up . I hope one day to be able to come on down and help with a build for BACA . Ok, look forward to watching more , Cheers !!!
Still have one of those in daily service. It is in a WW II Clark aircraft tug. It tows boats up to forty feet (and over, sometimes) around a marina shop. Wish I could find a rebuilt Plymouth six for a couple hundred bucks!
Man I love your videos. I have 83 Silverado that I had a rebuilt engine put in 5 years ago then coming home the other day I noticed it was starting to get hot right when I got home let cool off it didn't over heat check the water it was empty just was thinking I was a idiot for not checking the radiator then something in the back of my head said go pull the dip stick my hart sank I had a milkshake I have never done a head gasket job before it seems so intimidating but I came across your videos it made me feel better and more confident thanks
The 49 Dodge is cool. Would make a great daily cruiser. Sand it down, paint it battleship gray with red pin striping. Red wheels,chrome moon caps and chrome beauty rings. Hell, it might win a trophy.
as often as you end up jumping the solenoids on old ones you pick up, get a heavy duty push button used as a starter button and run wires with strong clips on the wires to connect to the solenoid. its easier and better than using screwdrivers
I think it's one of my favorite things in the world to hear an old motor run that hasn't ran in decades it's more fun than here in a brand-new one fire up
I had a '42 pickup and just loved the Art Deco styling with the Ram's head out front and pointed front end, even the fenders had deco stampings in them. I've been looking for a business coupe for a long time, nice find.
Love the "Marvels Magic Mystery oil"( upper cylinder lube)! I usually put it in spark plug holes several days prior. It us one of the few treatments approved by FAA for aircraft storage. They recommend fogging engine down t kill it. This is also an excellent way to store your onboard boat engines.
I spray p.B. or anything oily, actually down through the spark plug holes IN THE DIRECTION OF THE VALVES in case whichever ones are open happen to have taken on moisture,at least with flatheads,they can't hit a piston.Some of those in Dodge form were called Wayfarers.Good looking body.Good find.
i was never taught how to start an engine like that can someone explain to me how to do it so i know something new. would be greatly appreciated always love learning new stuff.
Those old MOPAR flathead 6 motors are pretty much bullet proof. I used one on my log splitter I built years ago. Of course the worst thing for an old motor is to let it sit for years neglected. I've also had a 1939 Dodge truck and a 1951 Chrysler (both flat 6 motors). Chrysler built them for years (even after 1959) as an industrial motor. I also had a portable welder with an industrial MOPAR flat 6.
Looks like the same carb on my 56 dodge truck motor I just rebuilt and got started last week. Purrs away at 400-500 rpm idle. Actually it all looks like my motor. Except I upgraded to a modern spin on oil filter.
thankyou for sharing i have a 48 especial delux just but a new jenerator can u hel and how to turn from 6volt to 12 and how hard isit new on this but i got bassic knowledge on how to change any part ???
thats cool my dad had a 51 plymoth business coupe. looked just like this he restored it with the original flat head 6 that was in it, but it had the old 3 on the tree
Thank you for your bother in making this video, as I enjoyed it very much. I suggest keeping this car original, as then you will have an authentic driving piece of history rather than creating another boring resto rod. If you want to go fast there are a number of inexpensive modern cars.
You know of any good parts sites where I could get some pistons and valves for one of these motors? My '46 dodge WF-32's engine needs pistons and possibly valves, as well as rings. Thanks in advance.
Hey that was cool ! I found myself pushing down with my right foot to get it to run for ya ! LOL ! Any way with that other motor that could be one cool ol car ! Is it true that the business coupe's had longer doors and no back seat as well as the top being shorter. Did the outer quarter panels bold on like the old mercury's ? Its just cool !
Jonathan you are one of the luckiest men alive!!! I wish we could find cars and trucks worth working on around here in michigan. By the time someone like me finds a old car its either rotted out sitting on the oil pan or people want 15k for them. Wanna adopt a son :-p Im a lic mechanic with a eltric and mechanical engineering degree LOL
Jonathan, great video for me. I am considering buying a 49 Business Coup. The floorboards need work as does the trunk floor. The exterior looks real good. Most of the chrome trim is there. The engine appears to be free, I only turned it with the fan and I haven’t made an offer yet but watching that old girl start, inspires me. Loved it! Where do you look for parts for old cars like that?
i bought a old 50 dodge flathead pickup for junk. the guy said clutch was bad and now engine was stuck seats was rotted. body was pretty good. i thought i got it out of gear all tires held air. pick it up with my wrecker. thinking i would pull it out go about 1/2 mile down the road and drop it and pick it up from the rear. was told the truck hasn't been touched in over 30 years. pulled out to the stop sign and i almost couldn't get it to stop. went to the large parking lot when i turned it it almost put me in the ditch. when i did get it to stop and got out the tires on that dodge was just slowly spinning. that damn thing started up and was running. got it out of gear hit the gas and it ran pretty good. picked it up from the rear and almost made it home and the damn thing broke in half. LOL
It's so awesome hearing old, long dormant engines roar back to life.
I got a 49 Plymouth on trade and it needed everything. I learned how to rebuild nearly everything on it and drove it to a car show. I can still hear that old flathead go. Thank you for the memories ❤️
I love it when these old relics wake up after decades of sleeping!
Amazing!
I'm an old relic
Zane Turner
Lol
I love those old Chrysler flathead engines, really enjoyed seeing your come back to life. You put a lot of good common sense in your videos. I've owned a 1948 Dodge Sedan Suicide doors since 1964, my Dad bought it from the original owner. It's always been garaged and has 39,000 miles on it now. I'd not had it started since 1993 but my 50th High School Reunion is this year so I want to drive it to the reunion. A new six volt battery, cleaning the points and some fresh gas and she's running again as of last week. Got to rebuild the brakes and put on a new muffler and tires and we're close to heading out again. I'm keeping it totally stock as much as I can.
I love the simplicity of old school motors, they're lovely
I’m reminded how simple cars used to be. A few tools and a couple of parts and you can make them run. Try doing that with today’s complicated cars. I miss the old days.
Yet another armchair expert,like you I've got loads of stuff started with missing rads without harm , keep bringing us your great adventures.
Anyone old enough to even know what a flathead engine is will at least know the basics in starting an engine that has sat for years and have their own way of doing things. I think he did a good job and I feel certain he did a lot BEFORE he started filming. And yes, the old Chrysler products and some other 6 volts (Packard, Hudson) systems were negative ground, but you don't negative ground 12 volts. I am 77 years old and still working on the old iron and have my way also. I like to blow the engine off with compressed air, check the oil, pull the plugs, squirt a little 10w motor oil in the cylinders and then attempt to rotate the engine back and forth and then see if she turns complete 360 degrees. If all looks good, pop the distributor cap, check for spark at the points, replace the plugs, rig up a temporary gas supply, and start the engine and let her idle, and speed her up gradually and check the oil pressure. And yes, these old engines will run for SHORT periods without water. The man does know what he's doing. As one reply stated, all of these old makes and models had fairly low compression, 6.5 to 7.5 and and if the engine cranks, and has at least minimum compression, fuel and spark, she will run. To be honest, I look under the hood of any late model and new vehicle, I don't have a clue as to what the hell I am even looking at. And I will NOT ride in any vehicle where the doors lock when you drive off. I'm always glad to see other folks save the old iron and keep these vintage cars/trucks from the crusher. Good video.
I had a 50 model Dodge in 65 it was bought at a service station for $25. It was wrecked on front end only had 32k miles on it. It had three speed with a fluid drive clutch. I drove it all over place!
6 volt Chrysler products had positive ground
The ground polarity matters little with old cars with no electronics, in theory the primary of the ignition coil should be reversed but it does not make a huge difference. As for not riding in a vehicle where the doors lock when you move, it depends where you live, on my own car it is an option they call "anti-hijack" I prefer to have the doors locked when I am driving slowly in the city. It also arguably makes the doors less likely to pop open in a roll-over. I love old cars but one thing they are universally lacking in is safety.
@@waltersmart1824 I had a '50 Dodge Wayfarer, "Fluid Drive" myself. Gor it in '64 from my brother-in-law for "get it running and its yours" deal.
All it needed was a 6 volt battery and some fresh gas. Like yours, it had been wrecked, missing the right half of the grill, lower half of the right fender around to the passenger door. My fried called it the "black bomb". She would hold 70 MPH all day long. I kept her on the road until it was burning as much oil as it was gas.
That fliud clutch was great on dates, since I din't _have_ to start off on low gear. Even started in third many times with no problems. It wasn't much on the drag strip :D !
@@g0fvt Any magnetic gages would be reversed, as would heater fan motors.
We used to joke that the light bulbs would work backwards and if you turned them on with reversed polarity, they'd make everything darker.
Sure was good to hear that old engine start up, nothing sounds like they do any more. Be safe. Peace.
I love listening to this cranking before it starts! Glad you got it to wake up!
I always like watching you getting old engines to run. Just need to have a spark and fuel and a decent battery and you always seem to get a so called impossible engine to start. Thanks for sharing
LUCKYLARRY I was about to say the same thing!!! lol
Starting any engine without water in the system will lead to an early death for the dry waterpump ?
Never mind the old, dirty oil and the bearings.
Peter Bloggs
You ain’t wrong but you’d be surprised at how resilient old parts are. By the way he did say he found a government surplus crate motor for this car for $250 so why not fire up this old boat anchor?
It's not rocket science 🤣
Had a '46 Plymouth 4-door sedan I
got started this way. Bought it in '74 for $50! Like this car, it sat for
several years. after getting it started my buddies and I drove it
all summer long. Good times
indeed!
Never get tired of watching these old girls being massaged back to life!
Love. This. Video. Can’t. Believe. It’s. Eight. Year. Old. ❤❤❤❤❤❤
I'd love to see you get it running and driving my Grandmother had one. Good Luck!
gotta love it. That's the first car I can remember ever being in. My dad had one when I was just a small fry. no back seat, I could play with my toys back there. It got turned into a race car, and my mom ran it in a powder puff derby. She won, too, not that the car was so great, but she could really drive.
My Father in law had a Wayfarer and it was really clean just needed an engine overhaul. They use to put those old 3 1/4 Bores in everything. I worked on a lot of them that were in forklifts and such. Unfortunately he ended up with some health issues and decided to get rid of it. I really wish I could have helped him fix it up but was having trouble with his eyes and didn't think he would ever be able to drive it. These are cool old cars!
I personally enjoy these videos by Johnathon more than a lot off the crap TH-cam posts. (Some are downright inflammatory). 😁😁🚗🚗😎
My old man used to own a '49 Dodge Tudor. It threw a rod while we were on vacation in '58 and he had a new engine put in. What a fun trip, or maybe not.
Jim Ervin
The piston-strokes on many Dodges,
Chrysler, and (later) Plymouth flathead sixes were VERY long. Great for hacking
around town, but a big strain on a
long highway trip. Not the least bit
surprising you would throw a rod.
Keep highway speeds down, or get
overdrive.
Need to put new cp rod bearings in the glove box to start on these.😎
Mighty promising , looking forward to seeing her roll again.
Man I love what your doing keep it coming thanks
Love seeing old iron come back to life!
Dang! Been searching old Dodge videos to help with my 52 Business Coupe. This one definitely did Watched this video a dozen times and just realized at the beginning of the video you had your battery hooked up backwards. Wish you would have mentioned that, it might have saved me hours. I never even thought of a positive ground system.
Hey Jonathan , hey from Canada! Really enjoying your videos, can't wait to see more. I gotta say you are truly creative , you are building true down to earth Rat Rods. I know when you are referring to " junk" you really mean treasures . Where I am , just trying to find anything like a Chevy six cylinder is like finding hens teeth. I realize trying to work and to do videos at the same time is difficult, but keep it up . I hope one day to be able to come on down and help with a build for BACA . Ok, look forward to watching more , Cheers !!!
Still have one of those in daily service. It is in a WW II Clark aircraft tug. It tows boats up to forty feet (and over, sometimes) around a marina shop. Wish I could find a rebuilt Plymouth six for a couple hundred bucks!
This coup has a _lot_ of potential!⭐️⭐️⭐️⭐️⭐️⭐️
Man I love your videos. I have 83 Silverado that I had a rebuilt engine put in 5 years ago then coming home the other day I noticed it was starting to get hot right when I got home let cool off it didn't over
heat check the water it was empty just was thinking I was a idiot for not checking the radiator then something in the back of my head said go pull the dip stick my hart sank I had a milkshake I have never done a head gasket job before it seems so intimidating but I came across your videos it made me feel better and more confident thanks
The 49 Dodge is cool. Would make a great daily cruiser. Sand it down, paint it battleship gray with red pin striping. Red wheels,chrome moon caps and chrome beauty rings. Hell, it might win a trophy.
Love this. Video. Every time. I watch. It
You sir are amazing. Keep up the vids and love seeing these old cars start up.
as often as you end up jumping the solenoids on old ones you pick up, get a heavy duty push button used as a starter button and run wires with strong clips on the wires to connect to the solenoid. its easier and better than using screwdrivers
your videos are really interesting I like watching them good job👍😎
I love the credits at the end! Also I’m going back through your old archives Jonathan! Awesome and fun projects
Pretty cool watching you trying to start her
I think it's one of my favorite things in the world to hear an old motor run that hasn't ran in decades it's more fun than here in a brand-new one fire up
Bobby V yeah especially an old flathead because you don't see those to often anymore
I had a '42 pickup and just loved the Art Deco styling with the Ram's head out front and pointed front end, even the fenders had deco stampings in them. I've been looking for a business coupe for a long time, nice find.
Love the "Marvels Magic Mystery oil"( upper cylinder lube)! I usually put it in spark plug holes several days prior. It us one of the few treatments approved by FAA for aircraft storage. They recommend fogging engine down t kill it. This is also an excellent way to store your onboard boat engines.
Love your videos. This is true hot rodding.
What?!?
That crate engine find! Hell yes!
A fine ride and I like and appreciate your story of possibly being a runner in its younger days.
SKip
Love seeing those things come back to life. How is it you have 48 thumbs down???
Perhaps because he has ignored so many basics and some people realise it ?
I think she sounds pretty darn good!! the engine puts out 100 horse power I can't wait to see it running
Love seeing the classics come back to life.
I love seeing this Johnathan this makes me happy
Johnathan I hope you still have this old salesman coupe
Had a 53 with the 217 flathead. Great little runner. Ugly car. Loved it.
What a car man hope you get her going again thanks
i'm curious of the progress you have made on this project
They are strong old engines I have the same thing in my 55 dodge you can still get a lot of parts for them. real nice car!
Dang it, now I want one. Still remember the 53 Pontiac flat head straight eight my brother had years ago....
Love the video, that was my first car! :)
So far, so good John...
Nice work! Love the car!!
I want a car like this or a Buick from this time period with a big ol' straight 8 in it. I love how they sound :)
Them old cars are Rip van winkles awakening after two generations!.
That’s a cool looking coupe it would be nice to put that back on the road
I spray p.B. or anything oily, actually down through the spark plug holes IN THE DIRECTION OF THE VALVES in case whichever ones are open happen to have taken on moisture,at least with flatheads,they can't hit a piston.Some of those in Dodge form were called Wayfarers.Good looking body.Good find.
Cool. From Cedar Park Texas.
Hi just found you today on a rainy cold day in Arizona of all places. I'd love to find an old pickup for hauling hay. Looks like fun.
very nice car always love to see your work my friend may God bless you always
That’s gonna be a nice ride.
My uncle Gary had one just like that in the 60s. I used to play in it waiting for him to get home from work. Someone stole it in the early 70s.
i was never taught how to start an engine like that can someone explain to me how to do it so i know something new. would be greatly appreciated always love learning new stuff.
I had a 50 cambridge had not run in 30 years. New 6volt and cleaned carb started rite up
She lives! Again, I think you are headed in the right direction toward the Dodge being a runner.
Skip
The needle valve is at the inlet. You can replace only the needle valve as a maintenance.
yess,.
Nice video Mater.
I agree. I had a 1949. These boys are too excited to get it right.
You stepped on your own tongue! LOL!!! I love these vids.
I had a 48 dodge business coupe back in early 1970s. It was soooo ugly it was beautiful.
On 6v wires inside dist ground out if not insulated
That would be one fantastic car to restore....especially if the numbers match. Most have been crushed so not many left in such good shape.
My first car was a 49 Dodge business coupe just like this. Bought it in' 65 for $35.00 and all it needed was a clutch.
Those old MOPAR flathead 6 motors are pretty much bullet proof. I used one on my log splitter I built years ago. Of course the worst thing for an old motor is to let it sit for years neglected. I've also had a 1939 Dodge truck and a 1951 Chrysler (both flat 6 motors). Chrysler built them for years (even after 1959) as an industrial motor. I also had a portable welder with an industrial MOPAR flat 6.
"Of course the worst thing for an old motor is to let it sit for years neglected." Tell us why?
Flat head six banger. Great vid.
Looks like the same carb on my 56 dodge truck motor I just rebuilt and got started last week. Purrs away at 400-500 rpm idle. Actually it all looks like my motor. Except I upgraded to a modern spin on oil filter.
thankyou for sharing i have a 48 especial delux just but a new jenerator can u hel and how to turn from 6volt to 12 and how hard isit new on this but i got bassic knowledge on how to change any part ???
thats cool my dad had a 51 plymoth business coupe. looked just like this he restored it with the original flat head 6 that was in it, but it had the old 3 on the tree
Really enjoyed this,thanks.
That is a nice car, interesting how fast the engine fired up after the earlier start attempts.
It/s ALIVE, gonna be a runner, for sure!
Love these videos of getting old iron to run! Will there be an update video anytime soon?
Thank you for your bother in making this video, as I enjoyed it very much. I suggest keeping this car original, as then you will have an authentic driving piece of history rather than creating another boring resto rod. If you want to go fast there are a number of inexpensive modern cars.
discerningmind
You are a great mechanic and person
I love this, skinned Knuckles and everything!!!
You know of any good parts sites where I could get some pistons and valves for one of these motors? My '46 dodge WF-32's engine needs pistons and possibly valves, as well as rings. Thanks in advance.
Awesome video man!!!
Hey that was cool ! I found myself pushing down with my right foot to get it to run for ya ! LOL ! Any way with that other motor that could be one cool ol car ! Is it true that the business coupe's had longer doors and no back seat as well as the top being shorter. Did the outer quarter panels bold on like the old mercury's ? Its just cool !
Jonathan you are one of the luckiest men alive!!! I wish we could find cars and trucks worth working on around here in michigan. By the time someone like me finds a old car its either rotted out sitting on the oil pan or people want 15k for them. Wanna adopt a son :-p Im a lic mechanic with a eltric and mechanical engineering degree LOL
Sounded good while it ran.
Wow I would love to own a car like that I'm a dodge and ford fan
Buddy had one swapped a 350. Sbc. And a turbohydro. Zoooooom😊😊
Hey good work it's a runner. .and good deal on the spare crate engine that should make the project git on down the road. FINS UP 👍 👍
+Eric Polston No Eric, no. No fins up. Not about a replacement motor. All original stock engine, FINS UP !
+Danny Boy ok yeeeyee FINS UP
Eric Polston Whoo buddy, Happy birthday, fins up !
Can't go wrong with vintage Jonathan.
new subscriber...love old cars, currently drive a .'37 D5. really don't comprehend 100 dislikes.
Those old flathead sixes are almost bullet proof.
Cool man. Hey what size socket is that?
Jonathan, great video for me. I am considering buying a 49 Business Coup. The floorboards need work as does the trunk floor. The exterior looks real good. Most of the chrome trim is there. The engine appears to be free, I only turned it with the fan and I haven’t made an offer yet but watching that old girl start, inspires me. Loved it! Where do you look for parts for old cars like that?
i bought a old 50 dodge flathead pickup for junk. the guy said clutch was bad and now engine was stuck seats was rotted. body was pretty good. i thought i got it out of gear all tires held air. pick it up with my wrecker. thinking i would pull it out go about 1/2 mile down the road and drop it and pick it up from the rear. was told the truck hasn't been touched in over 30 years. pulled out to the stop sign and i almost couldn't get it to stop. went to the large parking lot when i turned it it almost put me in the ditch. when i did get it to stop and got out the tires on that dodge was just slowly spinning. that damn thing started up and was running. got it out of gear hit the gas and it ran pretty good. picked it up from the rear and almost made it home and the damn thing broke in half. LOL
My friend put an 8 volt battery in his 48 Windsor and the Flathead 6 runs like a dream