Nice video! I would have suggested to instead use solar fuse terminal instead, then you can step down the 35mm³ to 10mm² and add a 30A fuse all in one go, without any soldering!
Bonjour C est intéressant pour le stockage,l encombrement et le poid n est pas facile à gérer. Je vais regarder la suite... Onduleur et gestion du BMS Bravo
Great stuff. Pretty much a dream project I would like to do one day when I can buy an affordable battery upgrade for my car. 😉 You mentioned sealing up holes with silicone. I would avoid that as I heard it creeps around and can cause contact problems.
Tog några sekunder och lite scrollande innan jag förstod varför jag sett videon förut, surt för visningarna på originalvideon men bra val ändå. Det blir en tumme, något som jag är väldigt restrektiv med men säkerhet är ju alltid bra. Kul projekt, hoppas det kommer fungera riktigt bra. :)
Lifepo4 is a so much nicer type of battery then Lipo. They don't care to be left on 100% of charge and you can use them from 0-100% all day long. And they wont run away thermaly and burn down your house like the Lipos do. I hope we get more EVs with Lifepo in Sweden. I will never have a Lipo car or big Lipo battery near my house.
Great inspiration for an upcoming house. I do have one question : when it comes to final installation, is it an issue to have it vertically mounted? chemically wise I'm pretty sure not, but there could be other things (sensor in the bms, ...). Thanks!
Lithium polymer batteries are the ones that catch fire. Don't keep them in your house. You want lithium ion for that but rather install them in an outside thermal bunker with the ability to smother them from air. You can get blankets specially for this purpose.
Thanks for a great video with clear instructions. I bought an Atto 3 which had a crash but the airbags didn't go off but the seatbelt emergency locking retractor did go off so i'm assuming a signal was sent to the battery it had a crash. If this is the case do you know if there is a fuse within the battery pack that will need replacing?
Thank you😃 sadly I can’t answer that for sure. All I know from the sonar car is that the airbags was intact. I did not know that BYD activated the belt tensioner without realising the airbag. Program A LILY go and connected to the battery and apply power, if the batteries IS okay you should clearly hear the contactors inside of the battery. But be very careful because then you will have high voltage out of the high voltage connector.
Very informative! This is amazing. Question, Is there any way to output 2 phase or 3 phase from a tesla model 3 via the ptc heater wiring to give the ability of V2L? I opened the module and it looks like you can easily add more wiring to connect an inverter directly. I think you can even adapt the hvil to the inverter as well. Seems simple enough and looks like it should work plug-and-play style.
@@HansFrisk there’s a fair amount of people, especially the guy with the ford lightning, that connected a battery in parallel to his traction battery to give him more range. It seems trivial but he’s not sharing any details nor is anyone else unfortunately. Can you give me a link to the Tesla v2h image you’re talking about?
Dala had relased a video about the recent reverse engineering of the id 3 battery as alternative to the nissan leaf he had used before. But I like this great idea to get an atto battery but I wonder where you get these batteries quite early after the car has been sold. I am on the verge of building another 2x 16 kWh LFP battery out of EV MB31 cells but of cause I would prefere such high voltage battery to replace also the old 4,6 kW inverters with 1 deye 3phase inverter.
Are there any plans to use the water pipes in the battery for either heating or cooling? I saw you adding the electric heat pads so I guess not. Just thinking which way I'll do it as well.
That was my plan from the beginning, but this is not made for water. This is directly heated and cooled with refrigerant. The channels are way too narrow to be used with water. I tried to blow air through it and it was really hard so water will be even harder.
Generally the load shouldn't be high enough to create heat, if your in a cold climate then heat pads might be needed (but I would have thought if the battery pack is on via cambus the bms should heat it self automatically if its too cold)
It is already now placed on styrofoam and a floor heating system that holds a temperature between 10-15 degrees centigrade. Works amazingly well. So I plan to stick with that solution.
@flyingtools thats great to know. We are planning for a place at my parents house. And the room is not isolated. But styrofoam was also my first idea. And this heating pads are easy to use. Thank.
@@MooseOnEarth It has to be cheaper to be worth it. My guess is 8000€. For 9000€ you can already get ready-to-use home storage battery solutions with even more capacity.
@@lukasweishaupt2708 Can you name a couple of home storage battery offers with more than 60 kWh below 9000 EUR (which would mean below 150 EUR/kWh)? Because I do not believe that, unless I see these offers.
Yes per standard the marking is AC 1000V / DC 1500V. And yes the spacing made it very confusing. Believe the Chinese standard is QC/T 1037-2016. There is an ISO standard as well for automotive charging cables.
The atto3 i bought had travelled a total of only 12 kms. The owner never managed to get out of the BYD dealer car park in Sydney before crashing it. The car has only panel damaged but due to the laws in my state in Australia it was written-off. I hope to use the battery for my home. I uploaded the dashcam if you want to take a look. It would be tragic to not reuse parts from this car th-cam.com/video/cYNJJP5GWGU/w-d-xo.html
Olá amigo acompanho o seu canal , o meu sonho é comprar uma bateria de veículo com essa capacidade de armazenamento de energia e fazer exatamente isso. Qual o seu contato e-mail ou whatsapp. Obrigado
Nice video! I would have suggested to instead use solar fuse terminal instead, then you can step down the 35mm³ to 10mm² and add a 30A fuse all in one go, without any soldering!
Hi 😃 Thanks, yes it will be something like that when i have it in the final place. As I mentioned this is just a temporary setup.😉
One of the best videos on the channel, thank you very much for sharing so much knowledge.
Thanks, so glad that you liked it 😃
Bonjour
C est intéressant pour le stockage,l encombrement et le poid n est pas facile à gérer.
Je vais regarder la suite...
Onduleur et gestion du BMS
Bravo
Great stuff. Pretty much a dream project I would like to do one day when I can buy an affordable battery upgrade for my car. 😉
You mentioned sealing up holes with silicone. I would avoid that as I heard it creeps around and can cause contact problems.
Thanks. You are right about that but there is silicones that at made for those specific purpose that not will react with the contact surfaces.
Nice video man!! The only thing would be that crimping rather than soldering the permanent solution of the cables
Thanks. Yes, this was only a temporary fix for a short test.
Tog några sekunder och lite scrollande innan jag förstod varför jag sett videon förut, surt för visningarna på originalvideon men bra val ändå.
Det blir en tumme, något som jag är väldigt restrektiv med men säkerhet är ju alltid bra.
Kul projekt, hoppas det kommer fungera riktigt bra. :)
Tack😃 vad kul att höra, extra kul att få din tumme då🙏 Tack!
Mkt bra! This is very informative and great inspiration! Keep it up!
Tack😃👍🏻
absolutely phantasic. Thanks for your effort, also to make videos about it.
Thank you 🙏☺️
Lifepo4 is a so much nicer type of battery then Lipo. They don't care to be left on 100% of charge and you can use them from 0-100% all day long. And they wont run away thermaly and burn down your house like the Lipos do. I hope we get more EVs with Lifepo in Sweden. I will never have a Lipo car or big Lipo battery near my house.
Brilliant video and information much appreciated
Thank you 🙏 So happy to hear that😃
Great inspiration for an upcoming house. I do have one question : when it comes to final installation, is it an issue to have it vertically mounted? chemically wise I'm pretty sure not, but there could be other things (sensor in the bms, ...). Thanks!
Hi that’s a really good question. I’m not really sure, but it might be harder to have an even temperature inside of the battery when standing them up.
Lithium polymer batteries are the ones that catch fire. Don't keep them in your house. You want lithium ion for that but rather install them in an outside thermal bunker with the ability to smother them from air. You can get blankets specially for this purpose.
Pretty much exactly what I’m doing.
I completely agree. But those lifepo4, especially the blade type cells in this battery are very safe.
Thanks for a great video with clear instructions. I bought an Atto 3 which had a crash but the airbags didn't go off but the seatbelt emergency locking retractor did go off so i'm assuming a signal was sent to the battery it had a crash. If this is the case do you know if there is a fuse within the battery pack that will need replacing?
Thank you😃 sadly I can’t answer that for sure. All I know from the sonar car is that the airbags was intact. I did not know that BYD activated the belt tensioner without realising the airbag. Program A LILY go and connected to the battery and apply power, if the batteries IS okay you should clearly hear the contactors inside of the battery. But be very careful because then you will have high voltage out of the high voltage connector.
Thanks
Very informative! This is amazing. Question, Is there any way to output 2 phase or 3 phase from a tesla model 3 via the ptc heater wiring to give the ability of V2L? I opened the module and it looks like you can easily add more wiring to connect an inverter directly. I think you can even adapt the hvil to the inverter as well. Seems simple enough and looks like it should work plug-and-play style.
Thank you 😃 sadly, I have no experience whatsoever on those batteries so I don’t even want to guess😅 sounds interesting though👍🏻
@@flyingtools ah dang ok🥲
If you check the internetz there is a hacked image for enabling V2H for tesla
And the ptc heater is dc
@@HansFrisk there’s a fair amount of people, especially the guy with the ford lightning, that connected a battery in parallel to his traction battery to give him more range. It seems trivial but he’s not sharing any details nor is anyone else unfortunately. Can you give me a link to the Tesla v2h image you’re talking about?
Very informative
Thanks for sharing
Thank you☺️
Dala had relased a video about the recent reverse engineering of the id 3 battery as alternative to the nissan leaf he had used before.
But I like this great idea to get an atto battery but I wonder where you get these batteries quite early after the car has been sold.
I am on the verge of building another 2x 16 kWh LFP battery out of EV MB31 cells but of cause I would prefere such high voltage battery to replace also the old 4,6 kW inverters with 1 deye 3phase inverter.
I bought it at a local junkyard.
Are there any plans to use the water pipes in the battery for either heating or cooling? I saw you adding the electric heat pads so I guess not. Just thinking which way I'll do it as well.
That was my plan from the beginning, but this is not made for water. This is directly heated and cooled with refrigerant. The channels are way too narrow to be used with water. I tried to blow air through it and it was really hard so water will be even harder.
@flyingtools ah. Dammit. That's annoying. Trying to find an air conditioning engineer would be rather difficult! Especially when you tell them why 😃
@ yes definitely 😅 heating is no problem but cooling will be much harder if needed. In my location I only have to be concerned about the cold though.
Generally the load shouldn't be high enough to create heat, if your in a cold climate then heat pads might be needed (but I would have thought if the battery pack is on via cambus the bms should heat it self automatically if its too cold)
Could you not find a mating low voltage connector housing? Looks like an automotive connector type from Molex or Tyco.
The car recycling company contacted me and said that they now have sent me one from another car☺️ So I wait until that one comes.
When you park your battery in the garden, how you sustain enough warmness/heat in it to stay above charging low temperature?
It is already now placed on styrofoam and a floor heating system that holds a temperature between 10-15 degrees centigrade. Works amazingly well. So I plan to stick with that solution.
@flyingtools thats great to know. We are planning for a place at my parents house. And the room is not isolated. But styrofoam was also my first idea. And this heating pads are easy to use. Thank.
Nice thinkering you managed there. Shouldn't the battery be topped up with coolant instead of drained?
Thanks. No, its meant for refrigerant. Not needed anymore in the way I am using it.
@@flyingtools oh, oke. I thought it might hold it more stable in temp due to use. Distribute of heat more even.
How expensive was that battery if i can ask?
My best guess: 10-15k EUR for this 60k LFP battery pack, not from a crash, hopefully.
I will give you all that information in an upcoming video. But it was cheap 😉👍🏻
@@MooseOnEarth It has to be cheaper to be worth it. My guess is 8000€. For 9000€ you can already get ready-to-use home storage battery solutions with even more capacity.
@@lukasweishaupt2708 Can you name a couple of home storage battery offers with more than 60 kWh below 9000 EUR (which would mean below 150 EUR/kWh)? Because I do not believe that, unless I see these offers.
@@MooseOnEarth Felicity, Malogica Solar, Delong, ... Just to name a few.
What is important parts of can bus software and hardware set up with Ethernet cable?
I will post a video about those parts asap.
@ Alright, man! Sweet!
i m confuse what or which color erthernet cabl plug go to which can hi c, low can , 12v , ignition
It might be clearer after the next update.
Any recommendations on where to source the EV batteries?
No, but best to buy locally from a trusted used car part dealer.
@flyingtools thanks. I'll do some digging about and see
Found a place 15mins away with very reasonable costs for the battery
Maybe it's "AC 1000V / DC 1500"... ?
Yeah, but if so, its a really strange way to mark a cable like that.
@@flyingtools Yep... too many space between the current rating and the current type, it's strange... great (and clean) job anyway!
Yes per standard the marking is AC 1000V / DC 1500V. And yes the spacing made it very confusing. Believe the Chinese standard is QC/T 1037-2016. There is an ISO standard as well for automotive charging cables.
Thanks for the Repost! Wäre did you purchase this battery?
Thanks. Local junkyard.
Super 😊
3d print a plug for the low voltage connector
Yes, I will see what i will come up with.
The atto3 i bought had travelled a total of only 12 kms. The owner never managed to get out of the BYD dealer car park in Sydney before crashing it. The car has only panel damaged but due to the laws in my state in Australia it was written-off. I hope to use the battery for my home. I uploaded the dashcam if you want to take a look. It would be tragic to not reuse parts from this car
th-cam.com/video/cYNJJP5GWGU/w-d-xo.html
Wow, that was crazy!! And I thought that my battery was new, 3000km and a few months before written-off😅 Thanks for sharing the video 👍🏻
So the next trend we see are the reformed catalytic converter stealers switching to stealing BYD battery packs?
Not the easiest and quickest thing to steal, but who knows…
A beutiful garden ornament?
Yes,maybe 😉
Where you got that battery in a first place
In a Swedish junkyard.
Olá amigo acompanho o seu canal , o meu sonho é comprar uma bateria de veículo com essa capacidade de armazenamento de energia e fazer exatamente isso. Qual o seu contato e-mail ou whatsapp. Obrigado