1Zpresso K-Series Grinder - Disassembly, Cleaning And Calibration (K-Max, K-Ultra, K-Plus)

แชร์
ฝัง
  • เผยแพร่เมื่อ 25 พ.ย. 2024

ความคิดเห็น • 32

  • @Frankkayser
    @Frankkayser หลายเดือนก่อน +2

    First time that I completely vleaned and calibrated my K-Ultra. Your video was very helpful. Straight forward and no unnecessary talking or information. Thanks buddy, happy brewing ❤

  • @werefed8613
    @werefed8613 6 หลายเดือนก่อน +4

    This video is fantastic. I’ve had mine for over five years and not one cleaning

  • @jm6651
    @jm6651 หลายเดือนก่อน +2

    Thank you for making this!

  • @1009wlwilling
    @1009wlwilling 8 วันที่ผ่านมา

    Hi master, thank you for making such wonderful video. I noticed that mine after re-assembling that the spokes on the adjustment dial do not align with the spokes on the body core piece. I wondered if I did something wrong and spokes came aligned at the factory!?

  • @陳成邦
    @陳成邦 8 หลายเดือนก่อน

    喜歡1Z K-Ultra!
    還在尋找等待新出一支1Z改款讓歸零動作能像泰摩栗子X-lite這麽簡單就更完美了。

  • @davecharvella4854
    @davecharvella4854 8 หลายเดือนก่อน

    Excellent! 👍👍

  • @BBuchanan3
    @BBuchanan3 5 หลายเดือนก่อน

    great video

  • @RonaldSurya
    @RonaldSurya 3 หลายเดือนก่อน

    Hi, thank you for making this cleaning hand grinder tutorial.
    I have further questions about cleaning and maintenance hand grinders
    Q1. Is it necessary to spray the bearings with food grade silicone (WD 40) and applied food grade grease on the grinder shaft to prevent steel rubbing each other ij the long run?
    2. Is it safe for the internal parts especially the grinder burr, if we spray / mist the coffe beans first before grinding to decrease static effects?
    TIA

    • @brewcoffeehome
      @brewcoffeehome  3 หลายเดือนก่อน

      Thank you for your comment.
      Q1: I personally don’t use lubricant. I just open it up and brush off the coffee residue, which works fine.
      Q2: Too much water is definitely not good, but a light spray or even dipping a spoon handle in water and stirring the beans should be fine. I always do RDT before grinding. However, I have heard that the bearings in some grinders, like the KinGrinder K6, might rust over time, but so far, I haven't had any issues with the bearings in any grinder.

    • @RonaldSurya
      @RonaldSurya 3 หลายเดือนก่อน

      @@brewcoffeehome Thank you for sharing 🙏

  • @Bassel74
    @Bassel74 8 หลายเดือนก่อน

    What's the best.?

  • @mikeyfelley
    @mikeyfelley 9 หลายเดือนก่อน

    Great Video very informative .
    Just a matter of interest how often would you recommend doing this ?
    Thank You 🙏

    • @brewcoffeehome
      @brewcoffeehome  9 หลายเดือนก่อน +3

      Actually the retention is really low, so there won't be lots of leftover grinds within the grinder. I usually clean it every month. If you grind darker roasted beans, I recommend cleaning it more frequently.

    • @mikeyfelley
      @mikeyfelley 9 หลายเดือนก่อน

      @@brewcoffeehome Brilliant. Thanks for your reply it’s much appreciated

  • @jht54321
    @jht54321 7 หลายเดือนก่อน

    Can we remove the bottom of burr set for K-Plus? I tried to twist. But doesn't seem to work

    • @brewcoffeehome
      @brewcoffeehome  7 หลายเดือนก่อน

      Please check 1:24 in the video. Are you referring to that burr set? If so, you need to twist it clockwise; it's pretty tight. I don't usually remove it every time I clean the burr.

    • @jht54321
      @jht54321 7 หลายเดือนก่อน

      @@brewcoffeehome Yea, you are right. I was trying to indicate lower burr ring. But mind was extremely tight so i am not sure if is tight or it can't be removed for a K-Plus model. Hence i didnt try further, worried that I might spoil it.

  • @simonchan9753
    @simonchan9753 9 หลายเดือนก่อน +1

    ZP6 is also K series?

    • @lsh-zi2lc
      @lsh-zi2lc 8 หลายเดือนก่อน +2

      Yes, just followed this for my Zp6.

  • @mohamedarafa9399
    @mohamedarafa9399 4 หลายเดือนก่อน

    Bearing has specific direction?

    • @brewcoffeehome
      @brewcoffeehome  4 หลายเดือนก่อน

      No, both sides will work for the bearing.

  • @george5120
    @george5120 4 หลายเดือนก่อน +1

    First things first:
    Why should this grinder ever need cleaning and how often? Cleaning looks like a lot of work and requires skill. As bad as disassembling and cleaning a gun.

  • @andrewtaylor9799
    @andrewtaylor9799 หลายเดือนก่อน

    Someone should invent a grinder that can be cleaned by simply putting it in the dishwasher with no disassembly or calibration. That would probably be very profitable for them. I've got better things to do with my time than the cleaning hassle I am seeing here.

    • @brewcoffeehome
      @brewcoffeehome  หลายเดือนก่อน +3

      A lot of people actually enjoy this process, but honestly, it works just fine even without frequent cleaning.

    • @Joao-or2kz
      @Joao-or2kz หลายเดือนก่อน

      It really should take you around 4 minutes once every 6 months
      I'm sure you can find the time

    • @andrewtaylor9799
      @andrewtaylor9799 หลายเดือนก่อน

      @@Joao-or2kz Maybe you can come to my house and clean it. I'll only charge you a dollar.

    • @Joao-or2kz
      @Joao-or2kz หลายเดือนก่อน

      @@andrewtaylor9799 lol way to tell a billion people how much of a lazy fuck you are

    • @BlownMacTruck
      @BlownMacTruck 15 วันที่ผ่านมา

      If you don’t want to clean it, buy another product or make your own. Clearly you think it’s be profitable.