You made it look so easy... I've been doing disassembly and assembly with everything from fine instruments to oil field equipment and never "pick up a hammer" to force anything (and am very good at keeping calm and focused) but putting in the probe retaining screw like to kicked my ass. I just couldn't get the threads to start!!!! I finally used cardboard pieces and rubber bands to shim and hold the cocking handle out a bit so it was directly under the access port and even it was difficult to engage the threads. THEN I had to take it out again to adjust the pin length. I did finally get it in but it took me almost 45 minutes.
@@bigearl8687 Had the 30 cal Maverick Sniper and did all the mods pin probe and transfer port and cabon fiber barrel wrap and then the MK3 came out. 🙄 Purchased the 357 Western RATTLER. No mods necessary. Wild hogs and coyotes are not happy. 10 days ago received the Panthera 22 700mm and SKOUT EPOCH 30 coming next month which after all mods to a MK3 Impact the EPOCH is actually cheaper 😳
On the .25 sleeve there is a flat side and a beveled side, I didn’t hear it mentioned, but the beveled side points forward and the flat side is towards the back so it’s flush with the probe. Good video as always!!
@@bigearl8687 Cant get enough info. Do i need a new liner for slugs .22? What happens if i dont fit a slug liner? Can i fire lighter pellets through a slug liner with accuracy?
Ernest, two points, One, when fitting the slug kit, there are two positions for the barrel to be fitted against, one is marked with an S the other with a P (slug or pellet), second point, I did not notice you applying any of the special grease to the new parts or the small bearing in the hammer adjuster to keep it from falling out during reconstruction. ! .
@@mauricedixon3843 Hi there ! Sorry for not getting back sooner to answer your question, NO was the answer, i'm still unsure what is correct as the rifle booklet is ambiguous to say the least. I would still appreciate a factual answer please of what is the correct way up for slugs/pellets.
My maverick came with the same spring guide weight as the slug kit :( 13.22g 947fps maxxed out with Hybrids :( Rear reg above 120bar and I lose velocity.
@@derivas007 join Airgun Nation or Gateway to Airguns and either site has lots of experienced and helpful airgun shooters with a combined experience of thousands of years. Someone has already done the research, take advantage of it.
Hello sir is the power kit exist for Maverick cal 0.30 today? And please to shoot slugs do i just have to turn on slug position? Is it enought ? Kiss from france Ty for your answers...🙏
I bought one! I want to fire slugs,being told i need to fit a new sleave to do this. All the vids on here,there is no mention of this,only the power kit.Which i am going to fit. Advice please.
Hi brother, I messed up the power wheel number on my .25 cal Maverick. The number 1-7 is not in order so how do I set it up so it will go back to it's order 1-7. Now Now number 3 is the most powerful number. Number 7 is the least power now.
@@tracyr5594 Then raise the power wheel by a point until you achieve what you want on a chrono.. My FAC 0.25 Maverick is set at 150 on the rear plenum (handle end) & 130 on the front one & I use 33grn Zan slugs from iHunter, that are fantastic for controlling various pests. Good luck.
Ernest i received two sleeves and 2 o rings in my Maverick slug power kit for my .25 cal. Is the o ring a spare? The other sleeve seems too big for the .25 cal barrel. How can I tell which to use?
Hi Ernest, i have a MAVERICK sniper on .22, all perfect until now, when ever o shoot now, a massive air flow hits my face and wont go truth the barrel, checked valves and oring, and even lubed them and the problem is still there, any idea what it can be? Thanks alot!!
Hi , I had the same problem, it turned out to be the very small O ring inside the barrel breach that had either broken or split. The part number from FX for my 0.25 caliber, was 145871 Not sure what it might be for your 0.22. Hope this helps, but it is a bit fiddly to fit, I did mine from the muzzle end after removing the barrel, with a cleaning rod head acting as a buffer to stop the seal going backwards into the barrel. Dont forget to wipe the new seal with PURE silicone GUN grease from Abbey products. Good luck.
I'm a brand new FX wildcat mk3 sniper shooter the slug power kit installed went easy and the power levels are insane 😎 but there are things I would like to change about the wildcat stock like the butpad shoulder piece I would like to upgrade it and fit a monopod at the side back off it there is nothing on the market for the wildcat mk3 sniper and I would like to have an 800mm barrel kit for it to bring it up a level that would be nice is there anything you guys can do to fill up the market because it's a big missing in the market greets from the Netherlands
Hee man! Mijn wildcat mk3 bt sniper is onderweg. Ik heb ook de slug power kit erbij besteld. Is dat beetje hetzelfde met installeren als in de video? Heb je miss ook een foto van jou set up? Fijn weekend! ✌🏻
hee man cool dat je de bt variant hebt besteld istalleren gaat het zelfde als de video heb zelf geen content op mn kanaal ik zou je wel een foto of filmpje kunnen laten zien heb je fb messenger ? k heb echt een maffe setup van waar int land ben je ?
@@GS.NL.1983 ik heb helaas geen Facebook.. ik heb evt wel LinkedIn of instagram. Ik denk dat ik hem dinsdag ontvang. Heb helaas nog geen scope die ik wil hebben is nog steeds uitverkocht. Ik woon in nieuw-buinen.(Drenthe) beetje ver van het zuiden vandaan😅
I use my standard FX Maverick FAC 0.25 to shoot Zan slugs of various weights, without any need to install a slug kit, all with staggeringly good results, at present I am using the 33grn slug at fps of 1050. What happens to your gun? I have found NO problems apart from a barrel clean every 500 shots & maintain a regular PURE gun silicone grease lube programme. good luck & happy shooting.
Hello, friend, good morning! I installed the slug power kit on my Maverick and noticed that the carbine was weaker than the original. Did you exchange the original spring of the hammer for another one? When watching your video, I noticed that I installed the hammer backwards, I positioned the spring in front and the thickest part of the hammer in the back, and in the video you installed the reverse, does that have any influence? Thank you for your help.
Yes it has a VERY big influence. If you haven't destroyed your hammer/valve yet, put it together the correct way and you should be 10-20fps faster. Pro tip: When disassembling things pay close attention / make photos of how it's originally assembled. You won't make such a rookie mistake anymore. ;-)
You would think for the price these rifles are sold for that the pellet probe screws would actually fit through the pellet probe without having to drill the pellet probe screw hole out. I thought that maybe I got a bad one. But after browsing the web it seems like it's common for them to be out of spec. And if you do buy one be sure to chamfer the hole and debur it after drilling it out.
The .30cal Mavericks already have the heavy hammer and spring for slugs along with the slug barrel (at least the Sniper does)...the .22 & .25 cal rifle 'slug kits' provide the .30cal hammer and spring along with adjustable probe for .22 & .25
I’ve got it at 945 with hybrids. I’m satisfied, but just was wondering what the deal was and why it’s not available for the 30. I didn’t go super high on the reg yet, but did Max out the hammer. Sniper version.
@@tormentorxl2732 mine is dialed in at 943fps (87.9 FPE) w/ FX Hybrids...4fps Std Dev across 31 shots. I'm not about to go through another 15-16hrs of tuning to get minimal gains at the risk of sacrificing accuracy. I do have the FX high flow transfer port installed in this .30cal Sniper
That is a cost of 501,600. Because of the deffects thst i told people to check themselves . I bought a fx Air guns because Matt said the barrels were perfect exactly the same and the target he showed at 100 yards was a quarter inch group which they can’t even get smaller than an inch and a half group with slugs at 100 yards. Mats videos should be taken down
why did you guys turn the comments off on your newer videos is it because of the truth about a fx liners. 228 people now have thanked me for saving them $2000 on one your airguns . But the thing to think about is how many of them haven’t thanked me that haven’t bought a gun from my fax because of my videos telling the truth
You made it look so easy...
I've been doing disassembly and assembly with everything from fine instruments to oil field equipment and never "pick up a hammer" to force anything (and am very good at keeping calm and focused) but putting in the probe retaining screw like to kicked my ass. I just couldn't get the threads to start!!!! I finally used cardboard pieces and rubber bands to shim and hold the cocking handle out a bit so it was directly under the access port and even it was difficult to engage the threads. THEN I had to take it out again to adjust the pin length. I did finally get it in but it took me almost 45 minutes.
Excellent video.
My Maverick is now running 1024 fps with 34gr slugs at 80ftlb. Best upgrade ever!
Thanks 👍
hi, would you tell me the adjustment on first regulator and the second regulator
Great video Mr. Rowe. Thank you.
Are the Maverick 30 cal slug kits coming soon??
Hello is the power kit exist for cal 0.30 today?
@@Fada2peche sold my Maverick
@@stedyone1090 why did you sell it , just curious
@@bigearl8687 Had the 30 cal Maverick Sniper and did all the mods pin probe and transfer port and cabon fiber barrel wrap and then the MK3 came out. 🙄
Purchased the 357 Western RATTLER.
No mods necessary.
Wild hogs and coyotes are not happy.
10 days ago received the Panthera 22 700mm and SKOUT EPOCH 30 coming next month which after all mods to a MK3 Impact the EPOCH is actually cheaper 😳
On the .25 sleeve there is a flat side and a beveled side, I didn’t hear it mentioned, but the beveled side points forward and the flat side is towards the back so it’s flush with the probe. Good video as always!!
Maybe thats why flat and beveled.
Idiot proof!
Important with weapons.
Hi , we can install without damaged valve ? Thanks 🙏
Yes 👍
@@FXAirguns thanks so much 👍
I did everything from the back were the power wheel is without removing the barrel on my wildcat mk3bt sniper 👍
I am going to buy one of these!
Great vid !!
How is it going so far
@@bigearl8687
Cant get enough info.
Do i need a new liner for slugs .22?
What happens if i dont fit a slug liner?
Can i fire lighter pellets through a slug liner with accuracy?
Great video Ernest
Muy buen video como siempre saludos desde ARGENTINA 👍👍👏👏🇦🇷
Ernest, two points, One, when fitting the slug kit, there are two positions for the barrel to be fitted against, one is marked with an S the other with a P (slug or pellet), second point, I did not notice you applying any of the special grease to the new parts or the small bearing in the hammer adjuster to keep it from falling out during reconstruction. ! .
Was there any response from Ernest as to which position the barrel should be in after it's reinserted?
@@mauricedixon3843 Hi there ! Sorry for not getting back sooner to answer your question, NO was the answer, i'm still unsure what is correct as the rifle booklet is ambiguous to say the least. I would still appreciate a factual answer please of what is the correct way up for slugs/pellets.
Where does the smaller of the o-rings go (the one you forgot on the table 1:30) ?
I have one as well, I guess somewhere on the pin ?
Hello! Please tell me what is suppossed to be the presure in the both of the the regulators?! Thank you
My maverick came with the same spring guide weight as the slug kit :( 13.22g
947fps maxxed out with Hybrids :(
Rear reg above 120bar and I lose velocity.
Hey could you share a PDF file with best settings for each pellets on impact m3
Please contact our customer service for the settings.
@@FXAirguns why you don t share a file with all best settings?fx impact m3 is a plateform for sharing best settings
@@derivas007 join Airgun Nation or Gateway to Airguns and either site has lots of experienced and helpful airgun shooters with a combined experience of thousands of years.
Someone has already done the research, take advantage of it.
@@bobjoatmon1993 do u have a link to share
Question: in the barrel for Slug it must set S in the top or P in the low position?
To shoot slugs you have to put P on the top. The letter you don't see is the letter you will shoot 😉
@@Fada2peche J'ai un doute sur la réponse.
@@cyrillecroix2821 non non c'est sûr et certain 😉
@@cyrillecroix2821 la lettre que tu positionné vers le bas sera le projectile utilisé...
Hello sir is the power kit exist for Maverick cal 0.30 today? And please to shoot slugs do i just have to turn on slug position? Is it enought ? Kiss from france Ty for your answers...🙏
Is there something in the works forcsemi automatic for FX? Regulated
I bought one! I want to fire slugs,being told i need to fit a new sleave to do this.
All the vids on here,there is no mention of this,only the power kit.Which i am going to fit.
Advice please.
Hi brother, I messed up the power wheel number on my .25 cal Maverick. The number 1-7 is not in order so how do I set it up so it will go back to it's order 1-7. Now Now number 3 is the most powerful number. Number 7 is the least power now.
I bought this item from Utah air guns they said slug kit for 22 25 and 30 cal is that wright
Do shooting slug without slug kit cause damage to my maverick?
Just slower
@@tracyr5594 Then raise the power wheel by a point until you achieve what you want on a chrono.. My FAC 0.25 Maverick is set at 150 on the rear plenum (handle end) & 130 on the front one & I use 33grn Zan slugs from iHunter, that are fantastic for controlling various pests. Good luck.
How many meters per second does it increase installing this kit
This kit to install it where to find.
Ernest i received two sleeves and 2 o rings in my Maverick slug power kit for my .25 cal. Is the o ring a spare? The other sleeve seems too big for the .25 cal barrel. How can I tell which to use?
Hi Ernest, i have a MAVERICK sniper on .22, all perfect until now, when ever o shoot now, a massive air flow hits my face and wont go truth the barrel, checked valves and oring, and even lubed them and the problem is still there, any idea what it can be? Thanks alot!!
Hi , I had the same problem, it turned out to be the very small O ring inside the barrel breach that had either broken or split.
The part number from FX for my 0.25 caliber, was 145871 Not sure what it might be for your 0.22. Hope this helps, but it is a bit fiddly to fit, I did mine from the muzzle end after removing the barrel, with a cleaning rod head acting as a buffer to stop the seal going backwards into the barrel. Dont forget to wipe the new seal with PURE silicone GUN grease from Abbey products. Good luck.
Is there slug kit for 177?
Approximately how many feet per second more will this Power give you
Up to 98
I'm a brand new FX wildcat mk3 sniper shooter the slug power kit installed went easy and the power levels are insane 😎
but there are things I would like to change about the wildcat stock like the butpad shoulder piece I would like to upgrade it and fit a monopod at the side back off it there is nothing on the market for the wildcat mk3 sniper and I would like to have an 800mm barrel kit for it to bring it up a level that would be nice is there anything you guys can do to fill up the market because it's a big missing in the market
greets from the Netherlands
Hee man! Mijn wildcat mk3 bt sniper is onderweg. Ik heb ook de slug power kit erbij besteld. Is dat beetje hetzelfde met installeren als in de video?
Heb je miss ook een foto van jou set up?
Fijn weekend! ✌🏻
hee man
cool dat je de bt variant hebt besteld istalleren gaat het zelfde als de video heb zelf geen content op mn kanaal
ik zou je wel een foto of filmpje kunnen laten zien heb je fb messenger ?
k heb echt een maffe setup van waar int land ben je ?
@@GS.NL.1983 ik heb helaas geen Facebook.. ik heb evt wel LinkedIn of instagram. Ik denk dat ik hem dinsdag ontvang. Heb helaas nog geen scope die ik wil hebben is nog steeds uitverkocht. Ik woon in nieuw-buinen.(Drenthe) beetje ver van het zuiden vandaan😅
Can I shoot slug without putting slug kit? If I don't put slug kit but shoot slug what happens to my gun?
I use my standard FX Maverick FAC 0.25 to shoot Zan slugs of various weights, without any need to install a slug kit, all with staggeringly good results, at present I am using the 33grn slug at fps of 1050. What happens to your gun? I have found NO problems apart from a barrel clean every 500 shots & maintain a regular PURE gun silicone grease lube programme. good luck & happy shooting.
is there anything stopping me fitting a maverick plenum on a Wildcat mk3 and then fitting my air tub eon the end instead of the bottle adapter?
Why change the barrel?
Hello, friend, good morning!
I installed the slug power kit on my Maverick and noticed that the carbine was weaker than the original.
Did you exchange the original spring of the hammer for another one?
When watching your video, I noticed that I installed the hammer backwards, I positioned the spring in front and the thickest part of the hammer in the back, and in the video you installed the reverse, does that have any influence?
Thank you for your help.
Yes it has a VERY big influence. If you haven't destroyed your hammer/valve yet, put it together the correct way and you should be 10-20fps faster.
Pro tip: When disassembling things pay close attention / make photos of how it's originally assembled. You won't make such a rookie mistake anymore. ;-)
@@hornyj1 obrigado
You would think for the price these rifles are sold for that the pellet probe screws would actually fit through the pellet probe without having to drill the pellet probe screw hole out. I thought that maybe I got a bad one. But after browsing the web it seems like it's common for them to be out of spec. And if you do buy one be sure to chamfer the hole and debur it after drilling it out.
I installed my kit just like this and now my maverick is shooting ALL OVER THE PLACE LIKE 15 inches in any direction.
Faça a doação de uma carabina dessa pra mim
Excelente
It is good, but I would like you to do slow and step by step. Thks
If you need further instruction please feel free to give our technician department a call.
Valentine's Day crafts
I’m having trouble finding this for my .30 Mav.
Not out yet.
I'm looking also.
The .30cal Mavericks already have the heavy hammer and spring for slugs along with the slug barrel (at least the Sniper does)...the .22 & .25 cal rifle 'slug kits' provide the .30cal hammer and spring along with adjustable probe for .22 & .25
@@vetteconnoisseur9531 slug kit not available for the 30 cal. yet
I’ve got it at 945 with hybrids. I’m satisfied, but just was wondering what the deal was and why it’s not available for the 30. I didn’t go super high on the reg yet, but did Max out the hammer. Sniper version.
@@tormentorxl2732 mine is dialed in at 943fps (87.9 FPE) w/ FX Hybrids...4fps Std Dev across 31 shots. I'm not about to go through another 15-16hrs of tuning to get minimal gains at the risk of sacrificing accuracy. I do have the FX high flow transfer port installed in this .30cal Sniper
What is the best pressure to set the regulators at for a 30 caliber
👍
That is a cost of 501,600. Because of the deffects thst i told people to check themselves . I bought a fx Air guns because Matt said the barrels were perfect exactly the same and the target he showed at 100 yards was a quarter inch group which they can’t even get smaller than an inch and a half group with slugs at 100 yards. Mats videos should be taken down
Wena wena
why did you guys turn the comments off on your newer videos is it because of the truth about a fx liners. 228 people now have thanked me for saving them $2000 on one your airguns . But the thing to think about is how many of them haven’t thanked me that haven’t bought a gun from my fax because of my videos telling the truth
I got robbed of my hard earned money I spent 15 grand on that junk
Can you watsap number, I have a question and need to show I do not speak English ...Thanks in advance
You may contact us via email at serviceusa@fxairguns.com