bro you dont understand how much i appreciate you makin this video the way you took off the valcovers for a HR is the most easiest and least complex way you didnt even take off nun of the grounds for the driver side or the injectors wtff i have all of my grounds disconnected because most tutorials on youtube these dudes take apart damn near the entire wire harness instead you just un loosened bare minimum and lifted it 🤦♂️ i wish you would have made this vid sooner lmao
Great video. Thanks for taking the time. Just wondering torque specs for reassembly, how you applied gasket in corner, and showed step by step reassembly. But thanks brother for this really appreciate it. Going to take everything apart in the next week.
this was the best valve cover video on youtube... thanks so much man.. I'm a go do mine right now, and if I have a reply on this it went great... if not... well...
Update: (not sure if my last one saved)... short form: got the entire left side off, thanks to the video. Tried putting my new valve cover on, but when torquing one bolt to 70ftlbs, it snapped in the housing. Got a bolt extractor kit, and it ALSO SNAPPED in the housing. Tried going a size up, but it stripped the housing. Now the car is in the garage, WITH NO CLUE what I should do. Calling Kal Tire tomorrow to see if they can somehow drill a bigger bolt hole for the housing, and maybe use a bigger bolt for the valve cover then. If not, probably gonna scrap the car. So it did not go well for me :) BUT the video was very helpful, can't stress how great this video was. However, if you're working on an 07 G35X, there's these pinch clips holding a lot of the wiring. Get some needle nose pliers or something to clip those out, it'll make a huge difference time wise. My brother PINCHED layers off my finger when I was trying to guide him to the clip, and I might need stitches on my finger now. But I'm sure others will be better 😀
@@Stage4Casper& just why would you torque those bolts to 70ft-lbs?? Max for those is maybe 8ft-lbs. I think you got confused with inch pounds & ft-lbs.
@ezkoshows7136 that's actually exactly what happened 😂 we were excited we were doing it so well,we were literally just in the moment, we weren't thinking, so we fucked up 😂 all good though, I got a specialist to come and get it out, and I'm gonna continue this weekend 👍🏼 VERY dumb mistake by us XD
UPDATE #2... I crushed the right side. I think it's far easier than the left side, actually. I didn't take off the fuel regulator entirely as mine was kind of stuck 😂 and I couldn't get it off. But it worked out anyways. ALTHOUGH... ANOTHER BOLT SNAPPED OFF !! I can't make this up. I wasn't even torquing to 5ft lbs, figured it wouldn't make it, I was only going hand tight, and it didn't even make it to "tight", I literally just tightened every other bolt though, and threw a bunch of slicicone into the housing/sides of it, gave it a day and a half, and when I tried to start up the car... it shut off on me when going into drive 😂 I tried starting it up again, and WORKED LIKE A CHARM, drove around for like 3hrs just because I was so excited, and because my spark plugs aren't getting flooded, IT FEELS SOOOOO SMOTH now. I can't thank you enough Jules. The instructions were so good, and easy to follow !! The only thing I had difficulty with when putting it together was that coolant hose on the left side, but I just lubed it with some dish soap, and got it on there (after about 45mins of struggling). Everything is all good though!! 🙂🙂🙂
Hey man I just got done doing mine on a g35 2008 and I got a lot of high circuit codes coming from the throttle body by any chance do you know the issue?
I got my valve cover gaskets done a white ago but didnt knoe about the cam ones, I didnt do the spark plug gaskets either, how long should the spark gaskets last? Im about to reach 100k, the valve gasket was replaced at 75 -80k
I had a quick question is there by any chance you know where I gone wrong? I turned it back on once I placed everything back , but it turns off immediately, I should mention that it’s been sitting for 2 weeks and it smells burnt from the exhaust ? Thank you bro !
The smallest ones go in spark plug holes. Cam seals go on where he pealed them off towards the firewall. He didn’t show spark plug gasket seal replacement just him pushing them in place while getting ready to place valve cover back on. He didn’t show the application of sealant on corners either.
This is the most difficult one I'm gonna have to do so far. I'm nervous but I like your vid the best so I'mma rock wit this one to help me do mine 😊 Thank you for posting this
![[MV] A leap of faith...ความเชื่อใจครั้งสุดท้าย (From "Petrichor the series")](http://i.ytimg.com/vi/U1piZH2CNXA/mqdefault.jpg)
bro you dont understand how much i appreciate you makin this video the way you took off the valcovers for a HR is the most easiest and least complex way you didnt even take off nun of the grounds for the driver side or the injectors wtff i have all of my grounds disconnected because most tutorials on youtube these dudes take apart damn near the entire wire harness instead you just un loosened bare minimum and lifted it 🤦♂️ i wish you would have made this vid sooner lmao
Mine leaking into my spark plugs do I need to replace just the seals and gaskets or the whole cover ?
My man thank you so much very educational you helped me do my Val covers on my 2008 infiniti ex35 journey 😊
Amazing video! I'm definitely going to replace my gaskets without paying that labour now !
Ur videos are 100x better then my eclipse gst videos I leave alot of stuff out man but u covered it all with zero time lapse almost bro good stuff man
Yo thanks a lot for making this video, man. I’m doing the job right now and this was super helpful.
Definitely a big help bro thank u ! Saving money workin on my car is clutch
Just bought my first HR good video gang🔥🔥🫡
Doing this tomorrow on my 07 Infiniti for the first time , gonna do both vals and sparks and coils packs shit look simple just need the tools 🤙🏽
Good luck 👍🏽
Oem air filters are so underrated
I used fel pro gaskets on high horsepower nissans and they work great. Sometimes they are slightly thinker than oem
Great video. Thanks for taking the time. Just wondering torque specs for reassembly, how you applied gasket in corner, and showed step by step reassembly. But thanks brother for this really appreciate it. Going to take everything apart in the next week.
Yessir my boi always coming through with them videos I just knocked mine out today much appreciated bro 💪💯
this was the best valve cover video on youtube... thanks so much man.. I'm a go do mine right now, and if I have a reply on this it went great... if not... well...
Appreciate you ✊🏽
Update: (not sure if my last one saved)... short form: got the entire left side off, thanks to the video. Tried putting my new valve cover on, but when torquing one bolt to 70ftlbs, it snapped in the housing. Got a bolt extractor kit, and it ALSO SNAPPED in the housing. Tried going a size up, but it stripped the housing. Now the car is in the garage, WITH NO CLUE what I should do. Calling Kal Tire tomorrow to see if they can somehow drill a bigger bolt hole for the housing, and maybe use a bigger bolt for the valve cover then. If not, probably gonna scrap the car. So it did not go well for me :) BUT the video was very helpful, can't stress how great this video was. However, if you're working on an 07 G35X, there's these pinch clips holding a lot of the wiring. Get some needle nose pliers or something to clip those out, it'll make a huge difference time wise. My brother PINCHED layers off my finger when I was trying to guide him to the clip, and I might need stitches on my finger now. But I'm sure others will be better 😀
@@Stage4Casper& just why would you torque those bolts to 70ft-lbs?? Max for those is maybe 8ft-lbs. I think you got confused with inch pounds & ft-lbs.
@ezkoshows7136 that's actually exactly what happened 😂 we were excited we were doing it so well,we were literally just in the moment, we weren't thinking, so we fucked up 😂 all good though, I got a specialist to come and get it out, and I'm gonna continue this weekend 👍🏼 VERY dumb mistake by us XD
UPDATE #2... I crushed the right side. I think it's far easier than the left side, actually. I didn't take off the fuel regulator entirely as mine was kind of stuck 😂 and I couldn't get it off. But it worked out anyways. ALTHOUGH... ANOTHER BOLT SNAPPED OFF !! I can't make this up. I wasn't even torquing to 5ft lbs, figured it wouldn't make it, I was only going hand tight, and it didn't even make it to "tight", I literally just tightened every other bolt though, and threw a bunch of slicicone into the housing/sides of it, gave it a day and a half, and when I tried to start up the car... it shut off on me when going into drive 😂 I tried starting it up again, and WORKED LIKE A CHARM, drove around for like 3hrs just because I was so excited, and because my spark plugs aren't getting flooded, IT FEELS SOOOOO SMOTH now. I can't thank you enough Jules. The instructions were so good, and easy to follow !! The only thing I had difficulty with when putting it together was that coolant hose on the left side, but I just lubed it with some dish soap, and got it on there (after about 45mins of struggling). Everything is all good though!! 🙂🙂🙂
Great video not many people like u explaining every detail
Hello would the 2009 370gt valve cover Looks different?
Did you reuse the spark plug gasket lmk asap ima going to reuse mine an wanted to know if you did too
Great video. Clear and concise. I appreciate the upload.
Hey man I just got done doing mine on a g35 2008 and I got a lot of high circuit codes coming from the throttle body by any chance do you know the issue?
I got my valve cover gaskets done a white ago but didnt knoe about the cam ones, I didnt do the spark plug gaskets either, how long should the spark gaskets last? Im about to reach 100k, the valve gasket was replaced at 75 -80k
Great Detailed video ! Keep up the great work , you’ve helped me fix my issue 🙏🏽
Appreciate you ✊🏽
I had a quick question is there by any chance you know where I gone wrong? I turned it back on once I placed everything back , but it turns off immediately, I should mention that it’s been sitting for 2 weeks and it smells burnt from the exhaust ? Thank you bro !
@@chrissrivera9043did you put the coil packs on right ?
@@ezamorazamora6978 yes sir , it turns out that I needed to replace both my throttle bodies , I appreciate you bro ! 🙏🏽
Do you have to remove the oil from the car before you do this? I’ll be replacing mine for the first time
No
Just successfully did this on mine. Thank you
Good job ‼️✊🏽
Where did you get those seals ?
Great vid thx... Where you located?
yo Brodie do you know a vid to where we can get to the head gasket
Had to sub and get you to 10k... vq all day
Might do this just to get to the 14055-jk20A hose 😢
Where do they cam seals go the little ones ? I missed that part
The smallest ones go in spark plug holes. Cam seals go on where he pealed them off towards the firewall. He didn’t show spark plug gasket seal replacement just him pushing them in place while getting ready to place valve cover back on. He didn’t show the application of sealant on corners either.
What torque you apply to the valve cover bolts ?
100 inch pounds
my spark plug tube seals are bad, are those removable? or you got to buy the valve cover too? g37
Did u watch? Cuz i replaced those
I don’t think he did if he did it wasn’t on the video I was wondering the same thing
Hello. Can someone please confirm if the VQ35DE and the VQ25DE uses the same rocker valve covers? Thank you.
How much could be the cost to do it?
depends on if you get shafted by the mechanic lol, should only be 2-3 hours labor max but i wouldnt be surprised if most tried charging 6ish.
For all the gaskets in the vid? 50 max. With maybe 1-3 hours of labor doing it ya self.
How long did this take in total?
I just replaced my g37 coupe gasket (passenger side) and did an oil change but now the car won’t start any tips?
make sure everything is plugged back in correctly
is it working now?
Thnaks,,, my car is readyyyy
right on time bro!
This is awesome. Thank you.
You didn’t change the spark plug tube seals? Not good man.
While a decent video you really should clean ur engine before popping the intake/valve overs off ....
Disconnecting your MAF sensors and throttle bodies didnt make you relearn the idle ?
always have to when removing throttle body
FAMMMM THANKYOUU‼️‼️‼️‼️‼️‼️‼️‼️
I want my oem air filrters back 😢
i cant find the part number!!!
so you bought the gaske kit
Nah he wished for it
This is the most difficult one I'm gonna have to do so far. I'm nervous but I like your vid the best so I'mma rock wit this one to help me do mine 😊
Thank you for posting this