I am so glad you guys made this video 5 years later it is still helping people out just did this for my dad the mechanic who put one on for us before had the whole thing zip tied all the way up there couldn’t even find the yellow release button tbh I think he broke the yellow release button but it just slipped out once I cut the zip ties but my dad won’t tell him anything
The pretend-engineers did such a horrible job on determining the location of all these sensors and their connectors. It's ridiculously difficult to access so many plugs on these motors and the exhaust system. The engineers should be required to work on one of these trucks sometime to see how shitty of a job they did.
Next time you guys remove a EGR value. Please do a video. I would like to do a emission tune up in the near future on my MX13. Thanks for all the information.
You can also test for voltage and continuity at the plug the make sure it is your nox sensor or not, pins 1 and 4 should show battery voltage, pins 2 and 3 should show around 55 to 60 ohms with the battery disconnected
hay clay peterbilt 2011 three indicators on one yellow check engine light the other red stop engine the third one yellow regen light with exclamation mark on it and i have those massages engine derated , noxlimit exceed due to quanttity ,aftertreat scr oprtate iduncement severity so what do you think thanx in advance
I saw a video on time saving tools and one them was called a Mini Ducter. You put the coiled wire end over a nut or bolt, etc and in about 30 seconds it's red hot and ready to come out. Great for working around fuel lines or fuels tanks that aren't torch friendly. ;-)
If you don’t have a computer to do it with take a look at this, super cheap and works great. For less than one tow bill you can usually get yourself out of a ton of jams and prevent de rating. th-cam.com/video/o10jJYeeZ50/w-d-xo.html
Another problem in the system is the SCR doser because it stays open and plug the outlet NOx sensor mounted on the exhaust pipe after the SCR catalyst...
I had a cam sensor code show up with my check engine light on. Not sure where this sensor is located on the engine. This happened after having an engine wash. Possible sensor connector loose. Any help you can pass on would be greatly appreciated.
Do you see a normal millage those are failing at? Reason I ask, Like the 386 SuperTruckerDan has. And most have the Paccar engine. And if I get back to driving. May try one out. That or throw new rears under my old 1995 T600 with The Series 60. Its a single axle right now.
Went from a 99 classic xl Detroit 13spd and 3.55s to a 13 t680 with the paccar a 10 and 3.42s worst mistake I've ever made keep your t6 forever its not worth the headache and unreliability
Is this the ONLY NOX sensor on the Paccar MX 13 ? I saw another video where a guy was under the passenger side of the vehicle and to pull of a heat shield and some other parts to get to it....? Hope to hear back from you soon. Thanks for the great video!!!
Have a question. I have a 2017 Kenworth T680 that has a tachometer that was working fine and now it's reading is approximately 5,000 rpm higher. Can you please tell me where the tachometer sensor is located at on a Paccar mx13? Thanks for your video and I am now a subscriber.
We are actually finishing a video now on all the tools need of you own a Paccar. I have several videos working on them and there’s more to come. We love Paccar engines.
Scott Pierovich I don’t have it anymore. We don’t keep them in stock. It’s a dealer item only so we just call out Peterbilt or KW rep and order them as needed due to the cost of the sensors.
Koon Trucking Thank you. My local dealer had my truck in for a recall and said outlet sensor was likely bad but they wanted to replace both. I'll just get outlet sensor when I pick up the truck and replace it myself. Thanks! Ps. If I need to replace inlet sensor I will have no problem doing it thanks to your video
I’m a NOx sensor application engineer. The NOx sensor comes with anti-seize already on the treads. Putting another form on anti-seize WILL POISON a NOx sensor causing it to read incorrectly.
The yellow tab just slides up, yeh right what you really mean is they stick like hell, then they break/chip as you lever them up, then you are stuffed!
I just cut the wire after I power probe it ND confirm it’s bad if it’s good but I still gotta remove it I’ve cut wires and then spliced them back together lmao.
Well i just cut the wire use regular deep socket Seems like mines are always stuck like a tick in a dogs ear TIGHT AS HELL I use the 22 mm socket going back together Am surpised you dont hv that snap wrench for that Dont forget to pull the diesel doser and clean it with carb cleaner to keep her rolling
Ken Lye it’s not a hard job to do at all. If you don’t have a way to clear codes or regen your truck take a look at this video, it will pay for itself the first time you need it to get out of a derate vs going to a dealer and paying them and having to wait for a regen th-cam.com/video/o10jJYeeZ50/w-d-xo.html It’s a great product to have !
SuperTruckerDan curious to know if you are having any emissions issues out of yours?? Also curious as to if there were any reasons besides cheaper upfront cost that lead you to chose paccar over Cummins
That’s why I do these videos. If you look in my video description you can see the discount code for the OTR performance tool that allows you to clear codes and force a regen super easy. It will also save a ton of money if you have issues and get derated. You can use it to get you to a truck stop or off the interstate. Money well spent for that! Here is a video of it in action to show how simple it is th-cam.com/video/o10jJYeeZ50/w-d-xo.html
Well i can tell you this. You saved me $840 in unnessesary fees as a new O/O. Even i can do this and i have all the mechanical skills of your average drunken chimp with a head injury. Just need to go get the new sensor next time im near a dealer. Also i actully have a diesel laptops system. Little more intense and lets me do a lot of dealer level commands. Bought it befofe i found out the OTR system was a thing
2 things. Never buy a kenworth. Nox sensor haha welcome to after treatment. Nox befor and Nox sensor after catalyst are going to cause you issues. There easy and quick to change. You can do it in less than 15 mins.
That part is probably most likely made overseas and they still rip people off like you being a business owner or the weekend warrior. Those dealers see nothing but dollar signs when you pull in for any kind of service... awesome video guys...👍👍👍
hay clay peterbilt 2011 three indicators on one yellow check engine light the other red stop engine the third one yellow regen light with exclamation mark on it and i have those massages engine derated , noxlimit exceed due to quanttity ,aftertreat scr oprtate iduncement severity so what do you think thanx in advance
I am so glad you guys made this video 5 years later it is still helping people out just did this for my dad the mechanic who put one on for us before had the whole thing zip tied all the way up there couldn’t even find the yellow release button tbh I think he broke the yellow release button but it just slipped out once I cut the zip ties but my dad won’t tell him anything
The pretend-engineers did such a horrible job on determining the location of all these sensors and their connectors. It's ridiculously difficult to access so many plugs on these motors and the exhaust system. The engineers should be required to work on one of these trucks sometime to see how shitty of a job they did.
Good videos we owner operators really appreciate just keeping coming thank you so much
There’s a bunch of handy videos in my playlist truck fixing. Check them out.
Next time you guys remove a EGR value. Please do a video. I would like to do a emission tune up in the near future on my MX13. Thanks for all the information.
How did he get "inside the little silver box" to unscrew the 2 bolts holding the electronic part....?????
You can also test for voltage and continuity at the plug the make sure it is your nox sensor or not, pins 1 and 4 should show battery voltage, pins 2 and 3 should show around 55 to 60 ohms with the battery disconnected
hay clay peterbilt 2011 three indicators on one yellow check engine light the other red stop engine the third one yellow regen light with exclamation mark on it and i have those massages engine derated , noxlimit exceed due to quanttity ,aftertreat scr oprtate iduncement severity so what do you think thanx in advance
Hey Clay, I think I finally figured out how you keep your tools so clean....you make Bill do all the work!! Lol 🤣
Good informative video!
Haha that’s right !
Really appreciate u sir, thank you and please continue helping out owner operator.
You bet
I saw a video on time saving tools and one them was called a Mini Ducter. You put the coiled wire end over a nut or bolt, etc and in about 30 seconds it's red hot and ready to come out. Great for working around fuel lines or fuels tanks that aren't torch friendly. ;-)
Do you guys do the recommended egr cooler flush? And if so can you make a video the next time or one showing all the def sensor locations on the mx
Lee Hill that would be an great video.
Thank you for video I replaced it but still got mil light on do I need to force regen any suggestions thanks
Yes you will have to clear the code and force a regen
If you don’t have a computer to do it with take a look at this, super cheap and works great. For less than one tow bill you can usually get yourself out of a ton of jams and prevent de rating. th-cam.com/video/o10jJYeeZ50/w-d-xo.html
@@KoonTrucking thanks a lot I did looks good so far
@@KoonTrucking I been thinking of getting it otr performance after but wasn't sure after 11 mon do I need new subscription?
Do you have to force regents after
Yes
@@KoonTrucking thanks
Another problem in the system is the SCR doser because it stays open and plug the outlet NOx sensor mounted on the exhaust pipe after the SCR catalyst...
Have you all done a video on the dpf diesel injector by the forward nox sensor
Have used an impact many time, never had any trouble, also do you blow out the insert with carb cleaner?
I had a cam sensor code show up with my check engine light on. Not sure where this sensor is located on the engine. This happened after having an engine wash. Possible sensor connector loose. Any help you can pass on would be greatly appreciated.
Is it possible to just clean the sensor instead of replacing?
Also wondering that same I need to clean or replace mine?
Is there an easy way to remove and replace the radiator in kw t680? My clutch fan exploded and sent the fan through the radiator.
It’s not that bad just undo hoses and unbolt it and get someone to help you sit it out of there or if you have a hoist or a cherry picker to help
Is the lambda sensor the same as the nox sensor?
What's the part number? Great video without nox part number
Can you explain how to change a oil pump and how to clean the oil cooler pls
Any ideas, 2016 t680 had box senor code replaced it and not even 30 miles later it’s back
I mean NOX
Did they change the right nox sensor ?
Nox codes can also come from egr issues
Do you see a normal millage those are failing at? Reason I ask, Like the 386 SuperTruckerDan has. And most have the Paccar engine. And if I get back to driving. May try one out. That or throw new rears under my old 1995 T600 with The Series 60. Its a single axle right now.
You never know with emissions the more they idle the more parts fail so ? Never know really. It’s very expensive just keeping emissions trucks going.
Went from a 99 classic xl Detroit 13spd and 3.55s to a 13 t680 with the paccar a 10 and 3.42s worst mistake I've ever made keep your t6 forever its not worth the headache and unreliability
If a nox sensor is bad, will it cause exhaust fumes to get Into the cab.
Not in my case. The STOP engine light activated on mine and I ended up having it towed to the dealership. Still waiting on the part, btw.
Is this the ONLY NOX sensor on the Paccar MX 13 ? I saw another video where a guy was under the passenger side of the vehicle and to pull of a heat shield and some other parts to get to it....? Hope to hear back from you soon. Thanks for the great video!!!
Outlet nox sensor is the one you saw
Is that also considered your after treatment intake nox
Nice video..what state and the address for your shop..hell if yall working that fast ill. Bring my truck there to get work done
North Mississippi. Bring it on in we will get you fixed ASAP
Have a question. I have a 2017 Kenworth T680 that has a tachometer that was working fine and now it's reading is approximately 5,000 rpm higher. Can you please tell me where the tachometer sensor is located at on a Paccar mx13? Thanks for your video and I am now a subscriber.
Paccar and isx cummins engines are the same codes and in the dpf/scr outlet nox sensor fail too..
What sensor is that right under the inlet?
Hey Clay, I noticed there was a similar sensor right below the NOx sensor, is that another one, or is it for something else?
There is also a Lamba sensor (air to fuel) and a temp sensor all in the same wad there.
I guess if I removed the whole DEF system this sensor doesn't matter anymore? Or am I wrong? Paccar MX
Do a video on egr system cleaning on the mx13…keep up the good work!
For how long this sensor last , I just replace mine about 3 months ago
Hey my man do you think aftermarket nox sensors are ok to use?
Do you know what code P3812 is
Is this a outlet or inlet?
I drive a 2014 T470 with a PX 9 , I never see any information on that engine .
We are actually finishing a video now on all the tools need of you own a Paccar. I have several videos working on them and there’s more to come. We love Paccar engines.
Do a video replacing the PM sensor . Thx
I find it funny how it is shipped in a super moisture resistant bag , buts bolts to side of the engine open to the weather .
Where you guys located
North Mississippi
What about the outlet one
Same thing just different location, it’s the one towards the rear of the truck 🤔
Do you have the Part number for the NOx sensor?
Scott Pierovich I don’t have it anymore. We don’t keep them in stock. It’s a dealer item only so we just call out Peterbilt or KW rep and order them as needed due to the cost of the sensors.
Koon Trucking Thank you. My local dealer had my truck in for a recall and said outlet sensor was likely bad but they wanted to replace both. I'll just get outlet sensor when I pick up the truck and replace it myself.
Thanks!
Ps. If I need to replace inlet sensor I will have no problem doing it thanks to your video
Scott Pierovich I have the video uploaded but haven’t released the outlet or rear nox yet
Scott Pierovich here’s the link .....
just for you
th-cam.com/video/Xnk49-OZMOo/w-d-xo.html
Scott Pierovich that’s service huh ?
My yellow tab broke now can't get it off
I really appreciate you guy's alot keep up the good knowledge
How come we can’t clean the nox sensors?
?? I’ve tried it with ZERO luck
I’m a NOx sensor application engineer. The NOx sensor comes with anti-seize already on the treads. Putting another form on anti-seize WILL POISON a NOx sensor causing it to read incorrectly.
The yellow tab just slides up, yeh right what you really mean is they stick like hell, then they break/chip as you lever them up, then you are stuffed!
You guys are the best
You mentioned $450-$500 for part...I just priced at our KW dealer $735 Intake NOx sensor!!! I want your dealer even if I have to pay shipping!
MHC Kenworth Tupelo MS
Same here. MHC Greensboro, NC wants $765.
@@georgequigley2360 I use Greensboro to but never buy from them go across the street to Peterbilt and it's always cheaper don't ask me why lol
@@truckingeveryday5703 I’ve got a good relationship with the parts guys. I get a real good price break on my parts.
I just cut the wire after I power probe it ND confirm it’s bad if it’s good but I still gotta remove it I’ve cut wires and then spliced them back together lmao.
Just quoted $1800 for this at a dealership
Well i just cut the wire use regular deep socket
Seems like mines are always stuck like a tick in a dogs ear TIGHT AS HELL
I use the 22 mm socket going back together
Am surpised you dont hv that snap wrench for that
Dont forget to pull the diesel doser and clean it with carb cleaner to keep her rolling
Next time get her hot and bump it with an impact it will bust loose.
If your going to go thru the bother of pulling the doser. Why would you put it back on. For an extra $260 I’ll take a brand new one please!!
$260 vs $10 ill think ill try cleaning first and if it doesn't help oh well cost me a burger haha
Thanks I’m going to try do mine. Got a code on it. You all are really helpful.😁👍
Ken Lye it’s not a hard job to do at all. If you don’t have a way to clear codes or regen your truck take a look at this video, it will pay for itself the first time you need it to get out of a derate vs going to a dealer and paying them and having to wait for a regen th-cam.com/video/o10jJYeeZ50/w-d-xo.html
It’s a great product to have !
Did mine . Wasn’t that hard. Hardest part of it was getting to it. That part really expensive 😳. Thanks for info. It saved me alot labor costs.😁👍
What's this for 3217 fmi15 code because that's the code I have can you please tell me
@@teddyduarte738 i did mine. It was the top nox sensior. But you might want to have it checked out before you do anything.👍
Thank you fellas
Great video, can you get wild bill to talk more?
He’s the quiet type
Great video guys thx for sharing 👍👌👏👍👌
Is the sensor prone to failure? seems kinda pricey, but the bigger the vehicle the more it's going to cost, great video
mechanicmike they do go out. Just one of those things with emissions trucks. I wouldn’t say they go out often just depends on your luck I guess.
$600 now with a $250 core
Thanks
Ahh damn it. All I had to do is see never seize on the video and I've got it all over me.
I know that’s right ! That will get all over you with less than will fit on the head of a toothpick !
I read your comment and now my neighbor’s wife is mad that it’s on her kitchen floor
Great video.
Thanks
SuperTruckerDan curious to know if you are having any emissions issues out of yours?? Also curious as to if there were any reasons besides cheaper upfront cost that lead you to chose paccar over Cummins
Great video
Thanks!
......you fucking kidding me? Thats it?! peterbilt wanted FOUR HOURS at $210 an hour to do this sensor.
Yep and you have to add in time for the regen.
That’s why I do these videos. If you look in my video description you can see the discount code for the OTR performance tool that allows you to clear codes and force a regen super easy. It will also save a ton of money if you have issues and get derated. You can use it to get you to a truck stop or off the interstate. Money well spent for that! Here is a video of it in action to show how simple it is th-cam.com/video/o10jJYeeZ50/w-d-xo.html
Well i can tell you this. You saved me $840 in unnessesary fees as a new O/O. Even i can do this and i have all the mechanical skills of your average drunken chimp with a head injury. Just need to go get the new sensor next time im near a dealer.
Also i actully have a diesel laptops system. Little more intense and lets me do a lot of dealer level commands. Bought it befofe i found out the OTR system was a thing
Anti seize pointless. With running and regens. It will burn off. Anti seize is good for alot but most after treatment components not worth time.
2 things. Never buy a kenworth. Nox sensor haha welcome to after treatment. Nox befor and Nox sensor after catalyst are going to cause you issues. There easy and quick to change. You can do it in less than 15 mins.
1050$ now 67$ core
800$ to replace this sensor guyz....
FIRST!!!!!
THAT'S RIGHT, LOL!!!!
That part is probably most likely made overseas and they still rip people off like you being a business owner or the weekend warrior. Those dealers see nothing but dollar signs when you pull in for any kind of service... awesome video guys...👍👍👍
Enjoy driving CAT with no headache till these craps have taken over the trucking industry,,, WTF 😢
hay clay peterbilt 2011 three indicators on one yellow check engine light the other red stop engine the third one yellow regen light with exclamation mark on it and i have those massages engine derated , noxlimit exceed due to quanttity ,aftertreat scr oprtate iduncement severity so what do you think thanx in advance
We would just have to look at it. Can’t diagnose stuff especially emissions issues without looking at them and seeing what’s going on
@@KoonTrucking thank you so much but the truck in saudia arabia , is thier any method to clear fault codes without ascan tool thanx haly
Awesome video thank you.