If the air/fuel screw is unblocked will I need to adjust it. Some videos say it needs to be set a 1½ to 2 turns. Also how do know you're order the right carburetor? I have a icebear mojo 150cc trike with gy6 motor model PST150-7. If the deception states it fits a 150cc will it work.
Type all that into Google. 🤦🏻♂️. GYK motor. Carb replacement. You’ll see in the descriptions. Numbers of your bike. Also directly under the carb. If you’re looking from driver side under the seat. Just below carb is 2 numbers stamped into engine. Top number is motor. Just search that number and your bikes year and your good
I was wondering if you could help me with an issue I'm having with the air box. Some of the rubber portions have ripped off on the connection . Almost like a ring of rubber ripped off because of wear and tear. Consequently I can't seal it will on to the carburetor. Almost like it's too short now to even extend to attach because of the ripped off ring a rubber. Do you have any advice or recommendations on how to seal the airbox to the carburetor that goes into the airbox?
Thank you sir great video ...I have a question I purchased a Powermotor PD24J Carburetor and it was missing the fuel/air flow screw but the hole is there , from the reviews on amazon it doesn't come with it, will it be ok with out it ?
Hello. I have a wangye eivissa 2 125cc scooter year of manufacture 2022. I notice you have an air drian filter. I have one on my scooter and its a YT80 WD air drain filter. I have 2 pipe being feed the bottom of the air filter and one pipe missing on the top. Would you happen to know where the missing pipe goes to as i dont have a service manual for the scooter. Cheers
I have an Xpro Bali 150cc. And the carburetor crapped out in less than a year with only 80miles, started leaking fuel and won't start. I'm contacting Xpro to see if they would send me a replacement.
I have a question, where does the tube that hooks up to the black connector go to? The black connecter piece you can see in this video that hooks up to the top of the motor and the front of the carburetor, there looks like a little tube going from it down to something and I cant figure out what it is.
Im having difficulties of finding the plug from main harness to plug in the carb signal. I can’t find out which yellow from main harness is for the carb so I can make connection. Thanks
so did i. i think you have to access the main electrical panel but i just cut the wires and replaced the carb and connected the wires via wire nut. runs perfectly.
It probably isn't good to not have it because if any feel or anything leaks out you could start a fire possibly if you go to one of your local scooter stores or bike stores you should be able to get it
Any carburetor should work good for you but if you want a really good one go with the 50cc 4-stroke high performance carburetor they have it on Amazon it comes with a better air filter and the bike will be a lot faster
This scooter (Aprilia SR 150) gives very very poor mileage (25-30kmpl). Is it possible to install 150cc Bike carburetor in Aprilia 150cc Scooter? #everyone
Chris Clark I ordered a carb for a 150cc scooter and it doesn’t have it. Do I have the wrong carb because it still won’t start after replacing the carb
Did you figure out why there’s no vacuum nozzle on the top? I’m in a shitty situation. I ordered a new carb and it didn’t have the nozzle on the top cap of the carb. The old one had one
I think u missing a few steps on showing us where all the dam tubes go.
Thats why im watching the video
Same
Top one attaches to the fuel pump. The bottom one is a drain, so it should have a screw plug on it.
If the air/fuel screw is unblocked will I need to adjust it. Some videos say it needs to be set a 1½ to 2 turns. Also how do know you're order the right carburetor? I have a icebear mojo 150cc trike with gy6 motor model PST150-7. If the deception states it fits a 150cc will it work.
Type all that into Google. 🤦🏻♂️. GYK motor. Carb replacement. You’ll see in the descriptions. Numbers of your bike. Also directly under the carb. If you’re looking from driver side under the seat. Just below carb is 2 numbers stamped into engine. Top number is motor. Just search that number and your bikes year and your good
I was wondering if you could help me with an issue I'm having with the air box. Some of the rubber portions have ripped off on the connection . Almost like a ring of rubber ripped off because of wear and tear. Consequently I can't seal it will on to the carburetor. Almost like it's too short now to even extend to attach because of the ripped off ring a rubber. Do you have any advice or recommendations on how to seal the airbox to the carburetor that goes into the airbox?
Can a 20mm head fit on that manifold? Or do i ned to buy that do?. Thanks
Thank you sir great video ...I have a question I purchased a Powermotor PD24J Carburetor and it was missing the fuel/air flow screw but the hole is there , from the reviews on amazon it doesn't come with it, will it be ok with out it ?
This video was really freaking helpful. Thank you so much. Time to ride!
Hello.
I have a wangye eivissa 2 125cc scooter year of manufacture 2022.
I notice you have an air drian filter. I have one on my scooter and its a YT80 WD air drain filter. I have 2 pipe being feed the bottom of the air filter and one pipe missing on the top.
Would you happen to know where the missing pipe goes to as i dont have a service manual for the scooter.
Cheers
What causes these carbs to just dump fuel at max throttle and pour out of air box?
Donald Duncan often times the float is stuck open, or your fuel pump petcock is just dumping fuel instead of being gravity fed.
my carberator has 2 other lines open below the fuel line? Do they stay open
I have an Xpro Bali 150cc. And the carburetor crapped out in less than a year with only 80miles, started leaking fuel and won't start. I'm contacting Xpro to see if they would send me a replacement.
Can you make one on the hoses and where they should be please
Should the fitting next to the drain on the carb be capped off or left open
I have a question, where does the tube that hooks up to the black connector go to? The black connecter piece you can see in this video that hooks up to the top of the motor and the front of the carburetor, there looks like a little tube going from it down to something and I cant figure out what it is.
I have the same issue. Did you figure it out?
Bro I need some help I’m not sure if I got the hoses in the right spot
What's the replacement carburetor model # for a 150cc Xpro Bali 150cc
Hy did you know if this carburator can fit on a Aprilia Malossi SR50 2017 with 70cc engine?
What type of gas do you put in the scooter?
Im having difficulties of finding the plug from main harness to plug in the carb signal. I can’t find out which yellow from main harness is for the carb so I can make connection. Thanks
Let me know too
so did i. i think you have to access the main electrical panel but i just cut the wires and replaced the carb and connected the wires via wire nut. runs perfectly.
hi where i can find body parts from this scooter?
Hi, I don't have that piece in the end of the fuel drain.Is it ok to let that way?Thank you.
It probably isn't good to not have it because if any feel or anything leaks out you could start a fire possibly if you go to one of your local scooter stores or bike stores you should be able to get it
Meant to say gas LOL
Hi, I have a Lance Cali Classic 50cc. Where can I buy the carburetor? thanks.
You will probably have to buy it on Amazon you just have to search up 50cc 4-stroke carburetor
I've always had to buy mine online
Any carburetor should work good for you but if you want a really good one go with the 50cc 4-stroke high performance carburetor they have it on Amazon it comes with a better air filter and the bike will be a lot faster
choke 2 wire.? where and what part you connect
....GREAT INSTRUCTIONAL VIDEO....5-STARS..!!!!
For a 50cc gy6 does it have to be a 19mm or below??
Without a big bore kit, 17.5mm tends to be the safest limit
Whats the difference between stock 50cc carburetor to 24mm carburetor
Thats not a 150cc it's a 19mm to put a 150cc on you will need a inlet manifold from the 150cc and a air filter with 42mm I/d.
This scooter (Aprilia SR 150) gives very very poor mileage (25-30kmpl). Is it possible to install 150cc Bike carburetor in Aprilia 150cc Scooter?
#everyone
Thank you for the helpful video!
Was any vacuum lines on the carburetor
O Jacks DIY on a 150cc there is one that comes out the top of the carb, there are none on a 50cc carb.
Chris Clark I ordered a carb for a 150cc scooter and it doesn’t have it. Do I have the wrong carb because it still won’t start after replacing the carb
How will i clean the carburetor?
Where is the vacuum lines?
Did you figure out why there’s no vacuum nozzle on the top? I’m in a shitty situation. I ordered a new carb and it didn’t have the nozzle on the top cap of the carb. The old one had one
Looks like a 19mm one not a 24 mm carb to me I put a 150 cc carb on mine I had to use the 150cc manifold.
Yeah, the 50cc ones use a 18-19mm hole versus a 150cc that uses a 24mm hole. The process is essentially the same
thanks, I'll be doing this later today!
Hey do u have a Instagram would like to talk to u about this
My scooter won't start after installing new carburetor
C’est bien expliqué rien à redire Bravo.
Nice light
Thank you for this video
So helpful
take a shot every time he says tight lol
That’s a Texas sized 10-4 there, bud
This video was not that helpful I couldn’t see were tf u were connecting the fuel things to
Great video man!
I got a bad ass scooter I've been working on also