Since you're open to suggestions on your on your videos one piece of advice that I've got and I'm not anybody to be weak giving advice but one and it's University a good idea less is more lower the volume on the background noise lower your volume try to emulate our buddy Bob Ross talk with a quiet voice very little background music if any at all nice and easy nice and slow clear clean hell yeah that's not a mistake it's a happy little Bush that dude was so awesome and if you have any questions about how to make a video go back and watch his videos I know you have I have they're awesome emulate that guy nice and calm nice and quiet and you know you're not mistakes your happy little accidents so keep doing what you're doing less-is-more and hell yeah Bob Ross was badass
I did this for the top on my outdoor kitchen I build for my patio today, and it could not have worked better. I got quoted $2,400 for a company to do them, I did them myself and it ended up only costing me $180 and a few hours of my time. Can’t thank you enough, keep the videos coming!
I was in the same boat for a 30ft concrete walkway. More time and money on my end compared to countertops, but saved thousands in a single day of work and couldn't be happier with the results. DIY!
How is it holding up? What did you use to seal it, and is it protecting it from stains while cooking? Just bought a house and need to redo my counter tops was thinking going concrete.
Great vid. A couple of pointers for those who are not as used to working with fast setting mortar as Michael is. Rapid Set Mortar sets (sets = maintains shape, but without a lot of strength) in 15 minutes at 70 deg F (20 C). That means at 70 you've got about 10-12 minutes to work with it. At 80 that becomes about 7 minutes and at 90 you're fighting to get it out of the bucket right after you mix it. So mix and get it out of the bucket as fast as you can. It's not like a regular mortar that gives you a lot of time to play. M's method of putting in the Flow Control after mixing the mortar works well, but a way to gain a little bit of speed is to add the Flow Control to the water first and then add the Mortar. That gives you quicker and easier mixing with less stress on your drill.
I am going to try adding the flow control to water as you suggest. My 1st bucket went nicely but my 2nd hardened before I could get it out of the bucket and the 1st pour was already hard by then also. I am going to have 2 buckets set up with water and flow control, bags opened and ready to pour, fully charged batteries and work in the shade in the AM before it gets hot. It was about 80 today and just didn't get it done as easily as he made it look in his video.
So glad you posted this, even though it's 5 months old. I'm in Houston, in the summer, trying to follow this method. By the time the concrete was mixing well it was getting hard. I even lost an auger in the concrete because it hardened too fast!!! I was ready to give up after 2 or 3 ruined buckets, but maybe our climate calls for a non fast setting mortar I guess. Thanks!!!
The Fast mortar sounds stressful: needs controlled climate maybe? However the tutelage on making the frame and beveling etc is great . I would stick with longer setting concrete, if you aren’t in hurry to get it done in 2 hours.
Hey everyone. I just wanted to drop a thank you to Michael. This guy has been super helpful. I watched all his videos and he gives great advice. He has given me the confidence to take on remodeling my floors and doing concrete slabs for a pergola. Mike had been kind enough to answer my emails even when he has been super busy. I have very much appreciated it. Thank you Michael.
I decided to try this for four countertops in my house. They turned out pretty good, but I have some tips as I ended up with some cracks. 1. Don't try anything fancy. I tried molding a sink opening and some cutouts, but the mortar broke. Which leads me to... 2. If you add reinforcement, i would try smaller steel than rebar. I added rebar, but the mortar cracked around it. 3. I found 4 qts of water made a better mixture than 5. 4. If you add designs, careful on the amount of mortar, I ended up with some big voids. 5. Be careful on the type of silicone and make sure it gets a good layer of wd40. The stuff I used bonded to the concrete in many places, and I spent a lot of time trying to get it off. 6. Let them dry longer than an hour, the ones I let dry for 24 hours worked better. Make sure to keep them wet as long as possible. The 1 hour strength is good, but why not let it get stronger? 7. Make sure to have a really good 1/2 inch drive drill with a paddle mixer, or a backup. I burned through (literally burned through) a cheap drill and had to borrow one, so I lost a batch of concrete and a bucket. I mixed 10 bags total. 8. Unscrew one side of the mold to make taking the mold off easier. Good job on the video, and keep 'em coming. I am happy with the project, just had some tips for any first timers.
I have done my counter tops using Suregrip Lite Weigth mix with polymore (not water) poored directly on surface with 3 in melamine sides. It allowed me to poor a thin layer of 1/2 in. The reinforcement was done by some Teflon T shape tip (about 3/8in high and a 1/4in wide - like the one that holds the price tag on a new shirt) mixed with the cement and color powder . I used a 12 in Metal trowel to level the top. SInce some Teflon tip were showing up like hair on your arm , i used some fondue liquid gas and burned them !
Did you use Mortar or concrete? You said concrete in a few places, so wondering if you did both? Also, did you use the flow control? I have forms ready to go, RapidSet mortar, but the stores have been out of flow control...so not sure if i should try a batch without the flow control or wait until I can source some.
@@PowerScissor "Light Weight" was written on the bag, and mixed to polemere liquid (1/2 gallon per bag of concrete ). Then, teflon tips for reinforcement and charcoal color concrete powder were added to the mix. The density of the mix itself is more a "Dump and push into place" then "Pooring and leveling liquid". You end up with a concrete 4 times stronger, no pores, very dense surface even after many years. It's been 5 years and at that time I had an expert contact given me expertise , how to's and selling me the right stuff. It was not cheap though. I did not use Flow Control (never heard of that until I read this article a week ago). Maybe we added a little bit of water to the mix , i just don t remember. Sorry. You have 30 to 45 min to poor and push and vibrate the mix on your surface before polymere sets in. 3/8" was the thiness surface. If you use a melamine cast and want to do some ocher veins, you would make a full hand patty that you push firmly into place on the melamine and drop ocher color concrete powder on th edge of that patty before putting the next patty. I would go with 5/8 of an inch and more when doing a cast. Here is a def of polymere concrete: Polymer concrete is an ideal material for constructions outdoors. It fulfills the highest requirements in terms of durability and low wear. The production of the material differs from that of cement concrete through the use of reactive resins instead of cement paste. This results in higher strength, which allows components to be manufactured with thinner walls - and therefore less weight. The decisive advantage, though, is the perfectly smooth and pore-free surface, which remains unchanged over many decades. This is an enormous quality advantage over cement concrete, which tends to become washed out due to weathering and flake in winter due to frost. Hope this helps. nobertps@hotmail.com
First of all great video man! So I just recently built on outdoor bar top using all the steps in your video. Here are some things I learned after building mine (since i now know what to do i will rebuild this in the fall) My measurements were 96in long, 30in wide and 2.25in deep. #1 do not attempt to mix this rapid set mortar mix in hot weather (above 85 degrees) because it will harden almost instantly. I went through 3 bags of mortar/flow control/ home depot buckets before I got so mad I almost gave up. Waited until later in the day (about 65 degrees) and then it mixed just like the video. And yes I used 55lb bags and 5 qts of water just like in the video. #2 get more bags of mortar mix and flow control than you think you need (you can always take them back) I used 4 bags for my measurements and it wasn't quite even with the sides. So I smoothed it out, let it sit and ran back to home depot for more mortar. It was already hardened when I returned so I just mixed the other bag and poured it on top to level it out all the way to the top. BIG MISTAKE! The second layer never bonded properly to the first layer and it just flakes off very easily (probably because it's so thin) #3 when you are making the live edge USE A BOARD UNDERNEATH WHERE YOU ARE HITTING! Some big pieces broke off and I had to glue them back with construction adhesive. #4 the sanded tile grout works great for the stencil but it will leave the mortar porous in those places so definitely seal the counter top. (Which he has another great video on how to do!) Sorry for the super long comment but I wanted to share what I experienced so it might help others. All in all this video is awesome and yes the cast really does just come right off of the mortar if you do it just like the video shows (I was really worried about that lol)
I am not sure if you are still getting many comments on this video, but I do have a comment. I was very skeptical of this method, but then again I've never tried making concrete counter tops either. For anyone else seeing this comment let me tell you...this process works amazing! I can not believe how wonderful my counter tops ended up. I made mine for an outdoor kitchen and they are perfect. I will say, it can be difficult though. If you make a square or rectangle that isn't too big...it would be pretty simple. I had 4 separate sections, all different shapes and sizes. Building the forms wasn't that hard, but getting my templates perfect took some time. The only other hard part was mixing all the concrete (mortar mix) quickly (I went through 9 - 55lbs bags). Again, I can't believe how amazing they turned out! Thanks for the great video. I couldn't nor wouldn't have done this without seeing this first. Thanks again!
Mark a question since you are a contractor. Using mortar for a countertop: Is it going to be as durable as cement? Is it going to scratch easier that cement?
Of all the comments, I can't believe that no one who has followed your tutorial and made a counter top has responded. Allow me to be the first. I wanted a small counter top, about 10" x 60" with an arced front for my outdoor bar. I followed your instructions from this video and the one concerning curved counter tops. I added some buff pigment for a brown color. Wow. The results were incredible. I was thrilled at how smooth the top was as well as the rounded edges created by the silicone caulk. It absolutely exceeded my expectations. My custom made counter top took me about a day and a half and cost me around $75 bucks. I couldn't be more pleased. If I ever make another one, the only thing I would do differently is take a little more care in applying and smoothing the caulk because any globs or imperfections will definitely show up on the edges. Thanks for the awesome video. You just made me look like a genius...
Well made and edited video. A few suggestions for those following these tips: - Make sure your mould is level in all directions before pouring and on strongly supported. - Add steel mesh or even glass fibres after you have the mix already poured on the mould surface. You may not need the added strength but it should not add much to the cost and you avoid the risk of the slab breaking while being moved. - Bring concrete/mortar mixture to the top of the form before screening it smooth. This way you have a smooth straight finish which will be easier to fit. - I would use less water as the finished product will be much stronger. Vibrate form for longer to reduce the number of air bubbles on the surface. - I made a sample mould and poured a 400mm square concrete slab so as to learn how this process works before pouring for a large Kitchen worktop. Enjoy
I’ve done a lot of renovations over the years. Never done poured concrete anything let alone a counter. I watch tons of videos on TH-cam to either learn something new or laugh at what people try. Gotta say, you have a real gift for doing these videos and seem to have some real talent in what you make. Excellent work my friend. Now I’m going to see what other vids you have.
Excellent does not cover your video-producing skills. I've not seen a flare for this before in my TH-cam viewing experience. Also, I was the guy at Buckeye Steel Castings in Columbus, Ohio who made the molds from two-part epoxy plastics. I would like to have had you as my Master for the jobs I did. Your incite and your tips and advice are worth untold savings in hours and frustration. When we were all laid off, the Super came and told me face-to-face that I had saved the company a lot of money and, believe me, he did not say that to the other journeymen who had fought him every step of the way! Well done, man! I've given you all the support I can....and you deserve it! John J Webb.
I’ve watched lots of videos on concrete counters. I come back to this one each time and rewatch. Soon as I get this house I’ve been patiently waiting on, I’m doing kitchen countertops your way.
You are a natural, not only in producing the video but in explaining the process and showmanship! Please, please make more stuff, and show technique and helpful hints. OMGosh, you keep your audience’s attention, you are not full of yourself, and you have an incredible talent. I love it!!!
My wife, son and I did our kitchen island. We mixed and poured 4 bags in 20 minutes. It went smooth because of your video 🍻cheers to you Sir! We are starting the the rest of the countertops next week.
I'm hooked! I made my first concrete bathroom vanity. My first bag of mortar never got out of the bucket and I burned up my drill motor. The second attempt, I was a bag short of mortar and ended up with a 1" counter with thousands of tiny pin holes (I guess I didn't vibrate it enough :) It did give me a practice piece to try my hand at the natural edge. Finally, poured it right on the third attempt. I used a plastic mixing trough, a bag of Set (because I'm slow) and a bag of Flow. I vibrated the bottom with the metal edge of my oscillating sander until my hand went numb and wah-lah, a finished counter with no bubbles and a perfect edge that I took my mason hammer to. Thank you for all the hard work making great videos. HGTV should offer you a DIY show. Matt Bashaw goes to my church and like you, he is an encourager. Keep up the great work!
Well, you're right! I watched a thousand of these videos and they all scared me off of this project. After watching your video I will now be trying this on the smallest of my kitchen cabinets. If it works well I will, most likely, be doing the entire kitchen. EXCELLENT video. Truly well done!
Have read all the comments. I love Monday Morning Quarterbacks. I am a disabled vet and your video made me believe I can do this with the small assistance while not bothering my friends to help in an over the top project. I love your stencil and ribbon work. would love to find a way to transfer pics onto the cement. I have an idea of creating a table for the backyard where i plan to makw a remembrance garden for my best friend..my dog who passed while I was disabled and almost sent me over the dark edge. I'm sure others have suggested or your own creativity has thought of some other crazy and or fun way to accent the cement . Thank you for the inspiration.
Mate, nice to watch a professionally done TH-cam video for once. Content was simple and concise, but the film making was the best feature. It was a pleasure to watch. I wish others would take note of how to present a video on TH-cam.
Plans, supply procurement, site readiness, mold assembly and preparation, mix preparation with accents, pour, cure, live edge detail, seal, install................totally just ONE HOUR! Still had time to dye my hair, wash my car, do three loads of laundry, paint 300' of wood fence, chop down the Sequoia in my front yard, take a round trip to the moon and smoke a brisket for lunch.......ALL BEFORE BREAKFAST!!!! That said...nice job for your first vid!!...from someone who is light years from doing one himself ;) Many happy returns!
That was one of the best videos I've seen. I have wanted to make concrete counters for my kitchen, but other videos make it sound difficult. I can so pull that off. Thanks. Look forward to more great videos.
Thank you! After lots of debating back-and-forth my wife and I decided to go with concrete countertops. So like all good home DIY people, I go to TH-cam and I find this entertaining, funny, very knowledgeable guy who tells me I Will not have to watch another video. He was right! I just did my first countertop of 7 foot long and it turned out amazing! Thank you again!!!
You have just changed my life! I hope you make all sorts of videos to improve the DIY experience! I am the DIYer but my husband hates my grand ideas and hates having to come help! I could get this all done before he even knows we have new counter tops! I was looking for video on a live edge table with concrete inlay rather than epoxy, so happy I found this because I think it’ll be much easier!
Watching vids for years, this is one of the few comments I've posted. As someone who has DIY'd just about every room in the house, I gotta say this is freaking awesome info and entertaining as well. Keep it up!
Thank you for taking the time to put very good information out there. Ive been a carpenter/mason/tile/yeah for about 28 years. One of the best finds I have had in the past decade is the Rapid-Set product line. I use both the Mortar Mix and Cement All very often and havent had any call backs, or unhappy customers. The Flow Control and Set Control are great additives depending on each application. You should submit your video to Rapid-Set :) For those who dont know, when it sets, it sets, lol Mike said it right "It's Gooooo time" Thanks again :
Was thinking of doing this for kitchen countertops but noticed he did not seal them...also noticed that rapid set cement all said it is for casting and the mortar mix dos not list that on the bag. Wondering if theres a reason to use the mortar mix over the cement all for a project like this and if there is a recommended sealer for use ina kitchen
So I'm 58 years old I recently had a trucking company and had to park all my trucks so I'm trying to figure out what's my next move and I've been watching a lot of these things on TH-cam this is awesome thanks bro
First video, 2 months ago, already 30K+ subscribers!!! You deserve it! This video has it all. Great information presented in a fun and easy way. No useless chatter. Opportunities to keep as is or take things steps further. Thought I might skip through parts.....nope. Got me hooked and watched every second! Keep it up!!! I like how you represented your Tigers too. A subtle way for you to rep Detroit. Very good job!!!
This was the best concrete countertop video I’ve seen. I loved that you showed how to make a design in the concrete. The video was well-paced, and I would guess you scripted it beforehand, which is an excellent choice. You kept us in the action, showed just enough of each step to explicate the techniques, and you did the necessary explaining but didn’t go overboard describing every minutia. Please keep making videos! I saw in your video description that you are aware of the loudness of the music. I’ll just mention that it was not only overly loud when you weren’t talking, but also loud enough to obscure your voice at times. I’m sure you’ll sort that out with trial and error, as you wrote.
First video??? Man, you'll have your own show on a diy channel very soon. Great presentation skills, very relatable, you have what it takes. Hello to the next diy star!
Michael, I think I love you...in a totally platonic and respectful way, of course. Yours is the second video I watched on concrete countertops and I'm not watching anymore.. Love, love your video. I am DIYer/rehabber and this looks very doable. I will be trying your method on a big ass top for a massive island I have in the kitchen.
Agree with the comment re “how the hell is this ur first video?” Great tips that I’ve never seen before (chipped edge, caulking with foam window cleaner, and flow control stuff). Your attention to detail is amazing in your products and video production. Thanks for the time/efforts given to strangers like me!
#1 assemble the table upside down so you're not smearing construction adhesive everywhere, wait for it to cure before trying to flip it back unless you can get a helper. #2 to help the new wood cuts to look similar to the rest (silver barnwoody type), you can age it by letting a bit of steel wool rust in 1/4 cup vinegar overnight, then dilute it 1:1 with water and put it on like a wood stain. It won't be a perfect match but it'll be a lot less noticeable than fresh wood cuts. #3 the flow control mixing in shot was awesome, good job.
Honestly I wasn't going to watch this video because of the length, but it was so well put together and entertaining that I couldn't stop watching. Not too mention how informative and clearly instructed everything was. Thanks! Keep it up!
Created a bathroom concrete countertop and backsplash following your instructions. After many learning lessons i.e. never mix quick set mortar in the hot sun, I finished. I love it. I layered sea glass and poured mortar on top for the backsplash. It looks like a mosaic. Thanks
I had a company install concrete countertops. They used the ”build in place” method with fiberglass reinforced concrete. If I had only known this method, I'd made them myself. Thanks for sharing your knowledge.
Oh my god what a great comment!!! Thank you so much! I would already have another video out but weather is making it difficult and so is the cursed iMovie app 😡. I have a love hate relationship with that app lol 😂 that app wiped out the entire video I just made so I’m trying to figure out how to backup my phone with out loosing everything else lol. Again, thank you so much for the awesome comments! I won’t let you down!
I have been wanting to do this for quite sometime, and as you stated, I've seen about a thousand of these videos. This, by far, is the best DIY video series on TH-cam. You were made for this, and I wish you all the best in your continued support of helping train all of us DIYers out here on the interwebs. I look forward to your next videos.
Loved the simplicity. So many want to complicate things, with intent of promoting outside business profits. Nice that see straight forward, with simple instructions. Same kind of things I try to do in instructing about electrical work. Nothing is hard in life when we know how & have an instructor who actually teaches rather than continually showing those learning that they are smarter. Thank you!
DUDE!!! DUDE!!! awesome!! you have so much talent, and to share it with the world is cool.your way of being is appealing and genuine. i hope you become a you tube monster!!! great job! now on my way to depot run!!!
My man, just did this for an outdoor bar top... Worked like a charm... The worker at Home Depot was saying I needed PSI 6000 because the mortar mix is too weak... Wish I could send him the pictures... Thanks my man, the step by step was amazingly easy to follow... 👍🏼
This is definitely a likeable video. Your sense of humor, and the fact that you went the extra mile to make it entertaining, verses just a how to video, kept me watching and wanting more. I was not at all bothered by the music volume.
i like shortcuts and I usually try and add shortcuts to shortcuts, but I didn't this time and it paid off. This is hands down the best how too video I've seen. I read the reviews on the rapid set mortar mix and almost didn't use the product due to the short work time, but I trusted and followed Mike's instructions. The Flow Control is incredible. Plenty of time to work with it and countertops are looking great. I used some old quarter inch trim moulding I had with Gorilla tape and bypassed the silicone part (impatient and needed to find a shortcut) and and the corners look great. I did a test run with different trims and it's $20 well spent. My wife picked the edge she liked best and I became familiar with process. Used Canola oil spray instead of wd 40 and released easily. Thank you Mike!
Place a board or something similar in from the edge during your live edge chipping, to prevent accidentally going in too far and knocking out too large a chunk.
You must make a diy wood fire pizza oven!! You are right I’ve watched 100 countertop videos and yours was the best... now do the same for a concrete wood fired pizza oven!!
back in the 50s used to cast 6" thick cold slabs in the larder. was left for a week to cure with shuttering still in place. motor oil/axle grease was the release agent.
OMG! Wayfinder! I cannot tell you how SORRY I AM that I did not reply to your AMAZING contribution from a whole year ago! TH-cam did not notify me about your SuperChat and I didn't see it until just now while I was stumbling around in my TH-cam analytics. I am so embarrassed and so so sorry man. Please accept my very humbled THANK YOU! You have no idea how much I appreciate your support and I'm even more appreciative that you gave me a SuperChat on this particular video. Even tho this video is my worst video ever (hahaha), it still holds a very special place in my heart because it changed my life. Again, thank you so much!
Came across this kind of accidentally, and went from having never, once, ever, even thought about concrete counter tops, to..."I'm doing this immediately!!" Great presentation and tons of info. Subscribed.
I made this countertop yesterday. Worked out just like described in the video! Excellent instructions! BTW...the Captain Morgan stance was performed. Made the project go that much more smoothly.
Hi Michael- I saw your videos and got hooked on the idea of concrete countertop for my new house. Had my contactor made the forms ( I don't have a tablesaw) and poured the most beautiful counter tops myself ... I love looking at them! Also made a bench & used rebar for the legs . Thank you for showing me how to be a concrete superstar!!
First video?? Solid editing, not bad music, volume control, steady camera *not* handheld, used a tripod, great topic, super clear instruction, 10/10 end product...... Liar. Impossibru face
Loved this video, watched it over and over, typed up instructions and list of supplies, trying it this week with one of my sons. DEPOT RUN! Boom!!!! What better way is there to spend time with your kids, we both have 1 week vacation time to do this project and others! Hanging out in his workshop all week. Thanks Michael, you are a talented and funny guy.
Love the video. Lots of good information, with more of the tips that you learn from experience. So many people spend a ton of time taking about making a mold, but if we made it this far we know at least how to cut a few pieces of wood. That tip with the spray window cleaner is awesome. You are the only person I have seen do that. Brilliant!!
Thank you so much Nathan! I did my best to give you guys enough bullet points and cool tips to get the job done without spending a ton of time on the project! Thank you so much for watching my video!
to keep your art in place, lightly apply several coats of hairspray over them before you pour the concrete. it will lock the sand in place and will not discolor the concrete.
👍🏼I do that with my chalk art I do on my pavers and wooden front porch and deck .. Helps keep the art around much longer. even when it rains (and I live in Oregon where it rains all the time.) As much as I love mod podge, and as much time as I spend on each piece of art, I want to enjoy it longer than a day or two but don't want it to be a permanent addition. Hairspray works wonders... As well as keeping my gel pen ink in place on plastics, rocks, and other random, non paper items, so I can then use spray mod podge to lock the art in place. I would have spaced it for something like this project. 👍🏼👍🏼👍🏼👌🏼
Yes, but I beg men to please lower the volume on the music. I had to turn up the volume really loud to hear his voice and that made in damn near painful when the music was playing. :(
A couple thoughtful comments I rarely watch an entire video but fast forward past the BS to get to the info. Your video was good on so many levels I watched the whole thing. That's especially remarkable because I have very little interest in cement counter tops. Making promises at the beginning caused me to want to watch to see how that would turn out and I found the video informative and entertaining. I especially liked 5 gallon bucket cam and pulling nails with your teeth but the best part was knowing all of this was about a friend needing a coffee table. You're a good friend and I really wanted to see you giving your friend the coffee table you made for him. All of my lavish praise comes at a price - just a suggestion. Tighten it up. There are several minutes that could be cut which would make a really good even better.
Removing rusted nails with your teeth, now that's how it's done! Another awesome build, I need to start stacking wood pallets behind my shed. I just finished a pallet wood crate on casters for raffle at my daughter's school, wish I share/post the pic here.
No one in the shadows here 😉👍🏻. I’m behind the camera and in front of the camera. I did both filming and editing on my iPhone 8. I very good buddy Jordon was definitely there for MUCH moral support and set up everything on social media for me and our video. For that I owe him everything! 😊
I used this method over the weekend to cast a 2' x 8' x 2" outdoor bar top. In general, it worked very well. A couple of notes and other things I learned: 1. If you haven't done this before (I hadn't), and if it's possible with your time or budget or desired level of effort outlay, I would highly recommend a "test cast" of either a full or half bag of mortar in a small mold, before making your finished product. Its really good to get your technique down and practice! A small mold would be about 2'x2'x1.5" which would be a single 0.5 cu/ft bag. 2. I used the WD-40 as recommended, however I forgot to wipe it down before pouring. Turns out this is NOT an optional step. My slab has very evident graffiti-like markings where I sprayed the WD-40. Frankly, the melamine is so slick I'm not even sure this step is needed. Again, a test casting would have found this issue. 3. Make sure whatever structure you are casting on is ROCK SOLID and doesn't allow for any sagging in the mold as the concrete cures. The melamine is surprisingly resistant to deflection but remember that each bag of mix adds 55+ lbs of weight and that adds up quickly. I had a large corner crack off my casting and I attribute that to the mold sagging in the middle over the sawhorses I had it placed on as the concrete cured.
@@garrettsoto1667 Each 55lb bag is .5 cu ft, so I used 4 in total. And i did not use any reinforcement, other than the corner breaking off (which was because the mold sagged while curing) the top is extremely strong.
that was amazing, and I can not believe this is your first video either. Great job for the idea, the delivery, the editing and the smile. You are a great asset
i'm sure your cousin is going to be ecstatic when you deliver that bad boy, and what a great gift, also if this is your first video i do believe you are on to a new career.
@@MichaelBuilds editing that video must have taken longer than making the table. Love the flow when you added it 😁👌Only a concrete guy can appreciate a product like that. Again incredible job with the table and video👍I'm a long time diver and treasure hunter. Check out my videos if I had your editing skills I would be set.
I watched/saved this video about a year ago and I had wanted to have a project to create a concrete countertop. The opportunity finally came up and the results were perfect. The steps you provided were very simple to follow and my new countertop turned out excellent. I have already received several compliments and people can’t believe I made it. Thanks for your video!
This is one of those you made it look easy videos. I'm sure a lot of work went into it. But it turned out great! A friend of mine needs a countertop and I think I will give this a try. Thank you!
Today (7.8.24)was the first day I ran into your videos and you nailed it. I know this was five yrs ago so I have a lot of videos to see to catch up to your current ones. I was in the market to build a table ( honey do list) for the holidays. Great Job…..
I have to say if this is your first video, then where have you been. That was fabulous and well done. You are a master craftsman on a higher level than all else. Keep your videos coming because I want to see more. You are the real deal and a pleasure to watch. I want to see what else you can do. Amazing man, you really rock.
Thanks for introducing this product to me. The fast set time of 2500 psi in one hour is a time saver. I would have never thought it was a CSA cement ! The light color is a bonus for design colors. I'm surprised they call it Mortar Mix since it has so many other uses. You definitely wouldn't want to use a traditional mortar mix because of the lime content and that it can't be used in thick pours(at least according to Sakrete). A few Home Depots keep stock on Quikrete concrete countertop bag mixes the last time I checked for about the same cost per pound than the Mortar Mix but I think this might be a better product. I would have thrown in some 3/8" rebar for some more strength during handling or at least some strips of cement block or brick steel joint reinforcement I'm not too keen on the WD40 as a mold release because of potential bonding issues with any stains or sealers. WD40 has a lot of VOCs that evaporate and don't leave much oil behind but I'm sure a wipe down with acetone would clean the concrete since you didn't use much. I prefer a furniture type carnuba wax like Johnson's Paste Wax.
After watching this video I felt confident building a 21’ outdoor kitchen and I needed 7 pieces of different sizes countertops so in order to be able to reuse the Melamine I spray painted the ends of the Melamine so i can reuse to complete my counter tops that I needed. And very nervous at first but luckily everything turned out just fine thank god. The wife is happy and I drink a beer and admire my work. Thank you Michael for making this video and making me look good with the family. Have a great summer because thanks to you my summer is going to be great. Oh and I also made a cap for my fire pit using your method and my fire pit looks awesome thanks again. 👏
Thank you so much. You literally added every single element to this table top that I want for the surprise outdoor kitchen I’m planning on building my husband. The countertop has been the piece that has scared me as I thought I would have to perfectly pour a smooth top directly on top of the grilling station. I feel so much more confident and I get the live edge I want without feeling like I need to buy expensive silicone molds.
Very easy to follow. Thanks for making this. I enjoy watching a lot of these videos but I don't always understand what some of these guys are taking about. I feel pretty confident I could make this now after watching this. I appreciated the step by step without all the technicalities. 👍 I'm excited now. Great job! Looking forward to seeing more of your stuff.
Thank you so much Regina! That means a lot to me because I really want to empower woman with this channel! I want to empower anyone that finds projects like these intimidating
I only need to watch your first video for you to convince me to subscribe. 12,000+ other people think the same thing 😁. Can’t wait to see what you have in store. Keep up the great work!
Just did this project with my son 5 days ago, and it turned out great. I only added 4 quarts of water, 1 bag each of Flow and Set control. I also am going to put my brand on the project after the fact with dye and a stencil. Thanks for the encouragement to do this project.
Had some trouble hearing you at times, but thoroughly enjoyed the video ! How about a video showing how to make mold for kitchen counter with sink holes for plumbing ?
Building an outdoor fireplace w/seating area. I was going to buy granite tops for the sitting area ends, but saw your video and decided to do the concrete instead. You saved me hundreds of dollars... Thanks! The video was AWESOME!
So incredibly sorry about volume of the music! Im still learning the ins and outs of iMovies and I promise you it’ll get better in the next videos.
This is great. You're hilarious.
Since you're open to suggestions on your on your videos one piece of advice that I've got and I'm not anybody to be weak giving advice but one and it's University a good idea less is more lower the volume on the background noise lower your volume try to emulate our buddy Bob Ross talk with a quiet voice very little background music if any at all nice and easy nice and slow clear clean hell yeah that's not a mistake it's a happy little Bush that dude was so awesome and if you have any questions about how to make a video go back and watch his videos I know you have I have they're awesome emulate that guy nice and calm nice and quiet and you know you're not mistakes your happy little accidents so keep doing what you're doing less-is-more and hell yeah Bob Ross was badass
Great stuff even better for us know it all old buggers my bit is to say that there be very little need for to screed it at all fsuch a small area
Oh yeah,one thing never say sorry again! (I appolige !) Never sorry got it ! It's all on you!
I was about to say something. Great comment but hard to hear over the music.
I did this for the top on my outdoor kitchen I build for my patio today, and it could not have worked better. I got quoted $2,400 for a company to do them, I did them myself and it ended up only costing me $180 and a few hours of my time. Can’t thank you enough, keep the videos coming!
I was in the same boat for a 30ft concrete walkway. More time and money on my end compared to countertops, but saved thousands in a single day of work and couldn't be happier with the results. DIY!
How is it holding up? What did you use to seal it, and is it protecting it from stains while cooking?
Just bought a house and need to redo my counter tops was thinking going concrete.
Great vid. A couple of pointers for those who are not as used to working with fast setting mortar as Michael is. Rapid Set Mortar sets (sets = maintains shape, but without a lot of strength) in 15 minutes at 70 deg F (20 C). That means at 70 you've got about 10-12 minutes to work with it. At 80 that becomes about 7 minutes and at 90 you're fighting to get it out of the bucket right after you mix it. So mix and get it out of the bucket as fast as you can. It's not like a regular mortar that gives you a lot of time to play. M's method of putting in the Flow Control after mixing the mortar works well, but a way to gain a little bit of speed is to add the Flow Control to the water first and then add the Mortar. That gives you quicker and easier mixing with less stress on your drill.
infraprods +1 I just did a one bag piece that was setting as it hit the mold. I would estimate mix temp in the high 80s.
I am going to try adding the flow control to water as you suggest. My 1st bucket went nicely but my 2nd hardened before I could get it out of the bucket and the 1st pour was already hard by then also. I am going to have 2 buckets set up with water and flow control, bags opened and ready to pour, fully charged batteries and work in the shade in the AM before it gets hot. It was about 80 today and just didn't get it done as easily as he made it look in his video.
So glad you posted this, even though it's 5 months old. I'm in Houston, in the summer, trying to follow this method. By the time the concrete was mixing well it was getting hard. I even lost an auger in the concrete because it hardened too fast!!! I was ready to give up after 2 or 3 ruined buckets, but maybe our climate calls for a non fast setting mortar I guess. Thanks!!!
97 degrees here in the southeast. Guess I don't stand a chance at this until late Fall.
The Fast mortar sounds stressful: needs controlled climate maybe? However the tutelage on making the frame and beveling etc is great . I would stick with longer setting concrete, if you aren’t in hurry to get it done in 2 hours.
OMG!! I'm doing it ! This was THE BEST ever! I'm a 66 y/o grandmother and I AM going to be making my countertops now.. You rock!
Show’em how it’s done Grama! 👍🏻😉
Hey everyone. I just wanted to drop a thank you to Michael. This guy has been super helpful. I watched all his videos and he gives great advice. He has given me the confidence to take on remodeling my floors and doing concrete slabs for a pergola.
Mike had been kind enough to answer my emails even when he has been super busy. I have very much appreciated it.
Thank you Michael.
I decided to try this for four countertops in my house. They turned out pretty good, but I have some tips as I ended up with some cracks.
1. Don't try anything fancy. I tried molding a sink opening and some cutouts, but the mortar broke. Which leads me to...
2. If you add reinforcement, i would try smaller steel than rebar. I added rebar, but the mortar cracked around it.
3. I found 4 qts of water made a better mixture than 5.
4. If you add designs, careful on the amount of mortar, I ended up with some big voids.
5. Be careful on the type of silicone and make sure it gets a good layer of wd40. The stuff I used bonded to the concrete in many places, and I spent a lot of time trying to get it off.
6. Let them dry longer than an hour, the ones I let dry for 24 hours worked better. Make sure to keep them wet as long as possible. The 1 hour strength is good, but why not let it get stronger?
7. Make sure to have a really good 1/2 inch drive drill with a paddle mixer, or a backup. I burned through (literally burned through) a cheap drill and had to borrow one, so I lost a batch of concrete and a bucket. I mixed 10 bags total.
8. Unscrew one side of the mold to make taking the mold off easier.
Good job on the video, and keep 'em coming. I am happy with the project, just had some tips for any first timers.
I have done my counter tops using Suregrip Lite Weigth mix with polymore (not water) poored directly on surface with 3 in melamine sides. It allowed me to poor a thin layer of 1/2 in. The reinforcement was done by some Teflon T shape tip (about 3/8in high and a 1/4in wide - like the one that holds the price tag on a new shirt) mixed with the cement and color powder . I used a 12 in Metal trowel to level the top. SInce some Teflon tip were showing up like hair on your arm , i used some fondue liquid gas and burned them !
Did you use Mortar or concrete? You said concrete in a few places, so wondering if you did both?
Also, did you use the flow control?
I have forms ready to go, RapidSet mortar, but the stores have been out of flow control...so not sure if i should try a batch without the flow control or wait until I can source some.
@@PowerScissor "Light Weight" was written on the bag, and mixed to polemere liquid (1/2 gallon per bag of concrete ). Then, teflon tips for reinforcement and charcoal color concrete powder were added to the mix. The density of the mix itself is more a "Dump and push into place" then "Pooring and leveling liquid". You end up with a concrete 4 times stronger, no pores, very dense surface even after many years. It's been 5 years and at that time I had an expert contact given me expertise , how to's and selling me the right stuff. It was not cheap though. I did not use Flow Control (never heard of that until I read this article a week ago). Maybe we added a little bit of water to the mix , i just don t remember. Sorry. You have 30 to 45 min to poor and push and vibrate the mix on your surface before polymere sets in. 3/8" was the thiness surface. If you use a melamine cast and want to do some ocher veins, you would make a full hand patty that you push firmly into place on the melamine and drop ocher color concrete powder on th edge of that patty before putting the next patty. I would go with 5/8 of an inch and more when doing a cast.
Here is a def of polymere concrete:
Polymer concrete is an ideal material for constructions outdoors. It fulfills the highest requirements in terms of durability and low wear. The production of the material differs from that of cement concrete through the use of reactive resins instead of cement paste. This results in higher strength, which allows components to be manufactured with thinner walls - and therefore less weight. The decisive advantage, though, is the perfectly smooth and pore-free surface, which remains unchanged over many decades. This is an enormous quality advantage over cement concrete, which tends to become washed out due to weathering and flake in winter due to frost.
Hope this helps. nobertps@hotmail.com
@@pauls.nobert3141 Thanks, I'm about to make my 2st attempt today.
@@PowerScissor i should clarify, I did use the same mortar and flow control as in the video.
First of all great video man! So I just recently built on outdoor bar top using all the steps in your video. Here are some things I learned after building mine (since i now know what to do i will rebuild this in the fall)
My measurements were 96in long, 30in wide and 2.25in deep.
#1 do not attempt to mix this rapid set mortar mix in hot weather (above 85 degrees) because it will harden almost instantly. I went through 3 bags of mortar/flow control/ home depot buckets before I got so mad I almost gave up. Waited until later in the day (about 65 degrees) and then it mixed just like the video. And yes I used 55lb bags and 5 qts of water just like in the video.
#2 get more bags of mortar mix and flow control than you think you need (you can always take them back) I used 4 bags for my measurements and it wasn't quite even with the sides. So I smoothed it out, let it sit and ran back to home depot for more mortar. It was already hardened when I returned so I just mixed the other bag and poured it on top to level it out all the way to the top. BIG MISTAKE! The second layer never bonded properly to the first layer and it just flakes off very easily (probably because it's so thin)
#3 when you are making the live edge USE A BOARD UNDERNEATH WHERE YOU ARE HITTING! Some big pieces broke off and I had to glue them back with construction adhesive.
#4 the sanded tile grout works great for the stencil but it will leave the mortar porous in those places so definitely seal the counter top. (Which he has another great video on how to do!)
Sorry for the super long comment but I wanted to share what I experienced so it might help others. All in all this video is awesome and yes the cast really does just come right off of the mortar if you do it just like the video shows (I was really worried about that lol)
Great tips!!! Thank you so much🙂
I would have loved to have seen a video on your process, that way we can all learn on what can go wrong. Thanks for sharing!
Never seen any concrete product set up as fast . Do this project in cool weather and get a helper . Did mine on a 90 degree day on July 4th in Texas .
After it was all done I was very pleased how the table turned out .
We all learn by trial and error and your’s were so helpful! Definitely will be aware of temperature and hammering live edge as you suggest. Thanks,
Dude, you need your own tv show. Great humor and edit, including info presented in a non boring way. Your first video? Great job.
Thank you so much! That means a lot to me !
Agreed....his first video?...killed it...entertaining and informative...great job
This is his own tv show that’s the beauty of it
Yes definitely need your own show on diy or HGTV!!
I am not sure if you are still getting many comments on this video, but I do have a comment. I was very skeptical of this method, but then again I've never tried making concrete counter tops either. For anyone else seeing this comment let me tell you...this process works amazing! I can not believe how wonderful my counter tops ended up. I made mine for an outdoor kitchen and they are perfect. I will say, it can be difficult though. If you make a square or rectangle that isn't too big...it would be pretty simple. I had 4 separate sections, all different shapes and sizes. Building the forms wasn't that hard, but getting my templates perfect took some time. The only other hard part was mixing all the concrete (mortar mix) quickly (I went through 9 - 55lbs bags).
Again, I can't believe how amazing they turned out! Thanks for the great video. I couldn't nor wouldn't have done this without seeing this first. Thanks again!
Dude, I'm a contractor and laugh at a lot of DIY projects... Your project, your video, your commentary, on point. Nice job man!
well Mark, what school and certifications do you have that makes you a contractor? You just DiY for money lol, all the same
@@stephenfresh1754 It's called a Contractor's License issued by the State Contractors License Board.
Oh lord Stephen don’t be like that.
Im licenced by the lord!
Mark a question since you are a contractor. Using mortar for a countertop: Is it going to be as durable as cement? Is it going to scratch easier that cement?
Of all the comments, I can't believe that no one who has followed your tutorial and made a counter top has responded. Allow me to be the first.
I wanted a small counter top, about 10" x 60" with an arced front for my outdoor bar.
I followed your instructions from this video and the one concerning curved counter tops. I added some buff pigment for a brown color. Wow. The results were incredible. I was thrilled at how smooth the top was as well as the rounded edges created by the silicone caulk. It absolutely exceeded my expectations. My custom made counter top took me about a day and a half and cost me around $75 bucks. I couldn't be more pleased.
If I ever make another one, the only thing I would do differently is take a little more care in applying and smoothing the caulk because any globs or imperfections will definitely show up on the edges.
Thanks for the awesome video. You just made me look like a genius...
Thank you so much! I want to see pictures! @michaelbuilds313 instagram!
You got to love it when a plan comes together!
Bob was bad ass !
Future home show TV Star right here folks. I’ll say it first.
I’m very impressed. Entertaining and well done. Thank you for this.
Thank you so much Rich!
Well made and edited video. A few suggestions for those following these tips:
- Make sure your mould is level in all directions before pouring and on strongly supported.
- Add steel mesh or even glass fibres after you have the mix already poured on the mould surface. You may not need the added strength but it should not add much to the cost and you avoid the risk of the slab breaking while being moved.
- Bring concrete/mortar mixture to the top of the form before screening it smooth. This way you have a smooth straight finish which will be easier to fit.
- I would use less water as the finished product will be much stronger.
Vibrate form for longer to reduce the number of air bubbles on the surface.
- I made a sample mould and poured a 400mm square concrete slab so as to learn how this process works before pouring for a large Kitchen worktop.
Enjoy
I’ve done a lot of renovations over the years. Never done poured concrete anything let alone a counter. I watch tons of videos on TH-cam to either learn something new or laugh at what people try. Gotta say, you have a real gift for doing these videos and seem to have some real talent in what you make. Excellent work my friend. Now I’m going to see what other vids you have.
Excellent does not cover your video-producing skills. I've not seen a flare for this before in my TH-cam viewing experience. Also, I was the guy at Buckeye Steel Castings in Columbus, Ohio who made the molds from two-part epoxy plastics. I would like to have had you as my Master for the jobs I did. Your incite and your tips and advice are worth untold savings in hours and frustration. When we were all laid off, the Super came and told me face-to-face that I had saved the company a lot of money and, believe me, he did not say that to the other journeymen who had fought him every step of the way! Well done, man! I've given you all the support I can....and you deserve it! John J Webb.
DIY, Build talent AND Camera, Editing, Story Telling skills? You are my hero!
WOW! Thank you so much Pete!!!
I’ve watched lots of videos on concrete counters. I come back to this one each time and rewatch. Soon as I get this house I’ve been patiently waiting on, I’m doing kitchen countertops your way.
You are a natural, not only in producing the video but in explaining the process and showmanship! Please, please make more stuff, and show technique and helpful hints. OMGosh, you keep your audience’s attention, you are not full of yourself, and you have an incredible talent. I love it!!!
For your first video, you NAILED IT! Good editing, no "yammering on" and was actually entertaining. Keep up the good work.
My wife, son and I did our kitchen island. We mixed and poured 4 bags in 20 minutes. It went smooth because of your video 🍻cheers to you Sir! We are starting the the rest of the countertops next week.
That’s awesome! I love that you got the family involved too! That’s what it’s all about!
Can you tell me how big it was? We are needing a 8' x 5' for our island!
I'm hooked! I made my first concrete bathroom vanity. My first bag of mortar never got out of the bucket and I burned up my drill motor. The second attempt, I was a bag short of mortar and ended up with a 1" counter with thousands of tiny pin holes (I guess I didn't vibrate it enough :) It did give me a practice piece to try my hand at the natural edge. Finally, poured it right on the third attempt. I used a plastic mixing trough, a bag of Set (because I'm slow) and a bag of Flow. I vibrated the bottom with the metal edge of my oscillating sander until my hand went numb and wah-lah, a finished counter with no bubbles and a perfect edge that I took my mason hammer to. Thank you for all the hard work making great videos. HGTV should offer you a DIY show. Matt Bashaw goes to my church and like you, he is an encourager. Keep up the great work!
Well, you're right! I watched a thousand of these videos and they all scared me off of this project. After watching your video I will now be trying this on the smallest of my kitchen cabinets. If it works well I will, most likely, be doing the entire kitchen. EXCELLENT video. Truly well done!
Thank you Dan! Let me know if you have any questions and I want to see pictures!
Have read all the comments. I love Monday Morning Quarterbacks. I am a disabled vet and your video made me believe I can do this with the small assistance while not bothering my friends to help in an over the top project. I love your stencil and ribbon work. would love to find a way to transfer pics onto the cement. I have an idea of creating a table for the backyard where i plan to makw a remembrance garden for my best friend..my dog who passed while I was disabled and almost sent me over the dark edge. I'm sure others have suggested or your own creativity has thought of some other crazy and or fun way to accent the cement . Thank you for the inspiration.
Mark Lazarcheff thank you for your service brother. I have all the respect in the world for you
Raul Sanchez serving was my honor.
There are a few TH-cam videos on transferring photos to stone, guessing it would work on cement too.
Thanks for your service Mark, it is because of men like you my grandchildren have a great future to look forward to. Never consider the dark edge.
I am a brick and block mason and been one since the 70s and consider myself knowledgable but even I learned something. Great Video.
Robert I cannot tell how much that means to me! Thank you so much!
This is the greatest DIY video ever made. This guy has ascended to rock star status.
Awwwwwwww! Thank you so much Andrew! Welcome to the channel man!
Mate, nice to watch a professionally done TH-cam video for once. Content was simple and concise, but the film making was the best feature. It was a pleasure to watch. I wish others would take note of how to present a video on TH-cam.
Plans, supply procurement, site readiness, mold assembly and preparation, mix preparation with accents, pour, cure, live edge detail, seal, install................totally just ONE HOUR! Still had time to dye my hair, wash my car, do three loads of laundry, paint 300' of wood fence, chop down the Sequoia in my front yard, take a round trip to the moon and smoke a brisket for lunch.......ALL BEFORE BREAKFAST!!!! That said...nice job for your first vid!!...from someone who is light years from doing one himself ;) Many happy returns!
That was one of the best videos I've seen. I have wanted to make concrete counters for my kitchen, but other videos make it sound difficult. I can so pull that off. Thanks. Look forward to more great videos.
Thank you! After lots of debating back-and-forth my wife and I decided to go with concrete countertops. So like all good home DIY people, I go to TH-cam and I find this entertaining, funny, very knowledgeable guy who tells me I Will not have to watch another video. He was right! I just did my first countertop of 7 foot long and it turned out amazing! Thank you again!!!
You have just changed my life! I hope you make all sorts of videos to improve the DIY experience! I am the DIYer but my husband hates my grand ideas and hates having to come help! I could get this all done before he even knows we have new counter tops! I was looking for video on a live edge table with concrete inlay rather than epoxy, so happy I found this because I think it’ll be much easier!
Watching vids for years, this is one of the few comments I've posted. As someone who has DIY'd just about every room in the house, I gotta say this is freaking awesome info and entertaining as well. Keep it up!
Thank you so much Jerry!!! I love comments like this!
Thank you for taking the time to put very good information out there. Ive been a carpenter/mason/tile/yeah for about 28 years. One of the best finds I have had in the past decade is the Rapid-Set product line. I use both the Mortar Mix and Cement All very often and havent had any call backs, or unhappy customers. The Flow Control and Set Control are great additives depending on each application. You should submit your video to Rapid-Set :)
For those who dont know, when it sets, it sets, lol Mike said it right "It's Gooooo time"
Thanks again :
Was thinking of doing this for kitchen countertops but noticed he did not seal them...also noticed that rapid set cement all said it is for casting and the mortar mix dos not list that on the bag. Wondering if theres a reason to use the mortar mix over the cement all for a project like this and if there is a recommended sealer for use ina kitchen
So I'm 58 years old I recently had a trucking company and had to park all my trucks so I'm trying to figure out what's my next move and I've been watching a lot of these things on TH-cam this is awesome thanks bro
First video, 2 months ago, already 30K+ subscribers!!! You deserve it! This video has it all. Great information presented in a fun and easy way. No useless chatter. Opportunities to keep as is or take things steps further. Thought I might skip through parts.....nope. Got me hooked and watched every second! Keep it up!!! I like how you represented your Tigers too. A subtle way for you to rep Detroit.
Very good job!!!
kidphillyorg People love simplicity. The easier, the better😀. Got me thinking of doing one of these tables myself!
This was the best concrete countertop video I’ve seen. I loved that you showed how to make a design in the concrete. The video was well-paced, and I would guess you scripted it beforehand, which is an excellent choice. You kept us in the action, showed just enough of each step to explicate the techniques, and you did the necessary explaining but didn’t go overboard describing every minutia. Please keep making videos!
I saw in your video description that you are aware of the loudness of the music. I’ll just mention that it was not only overly loud when you weren’t talking, but also loud enough to obscure your voice at times. I’m sure you’ll sort that out with trial and error, as you wrote.
First video??? Man, you'll have your own show on a diy channel very soon. Great presentation skills, very relatable, you have what it takes. Hello to the next diy star!
Michael, I think I love you...in a totally platonic and respectful way, of course. Yours is the second video I watched on concrete countertops and I'm not watching anymore.. Love, love your video. I am DIYer/rehabber and this looks very doable. I will be trying your method on a big ass top for a massive island I have in the kitchen.
Agree with the comment re “how the hell is this ur first video?” Great tips that I’ve never seen before (chipped edge, caulking with foam window cleaner, and flow control stuff). Your attention to detail is amazing in your products and video production. Thanks for the time/efforts given to strangers like me!
Thank you so much Howard!!! I can’t tell you how much that means to me!
#1 assemble the table upside down so you're not smearing construction adhesive everywhere, wait for it to cure before trying to flip it back unless you can get a helper.
#2 to help the new wood cuts to look similar to the rest (silver barnwoody type), you can age it by letting a bit of steel wool rust in 1/4 cup vinegar overnight, then dilute it 1:1 with water and put it on like a wood stain. It won't be a perfect match but it'll be a lot less noticeable than fresh wood cuts.
#3 the flow control mixing in shot was awesome, good job.
Re: #1, He had shims on the base when he placed the top, which were removed when it was in place.
Re: #2, Good tip, thanks!
Honestly I wasn't going to watch this video because of the length, but it was so well put together and entertaining that I couldn't stop watching. Not too mention how informative and clearly instructed everything was. Thanks! Keep it up!
Oh my god thank you so much Kurt!!!
Created a bathroom concrete countertop and backsplash following your instructions. After many learning lessons i.e. never mix quick set mortar in the hot sun, I finished. I love it. I layered sea glass and poured mortar on top for the backsplash. It looks like a mosaic. Thanks
I had a company install concrete countertops. They used the ”build in place” method with fiberglass reinforced concrete. If I had only known this method, I'd made them myself. Thanks for sharing your knowledge.
Lol 😂 thank you so much Kevin! Sort I’m late lol
Your video should be a tutorial for how to make an excellent video. Great Job! Your humor is inspiring....Loved every minute.
Oh my god what a great comment!!! Thank you so much! I would already have another video out but weather is making it difficult and so is the cursed iMovie app 😡. I have a love hate relationship with that app lol 😂 that app wiped out the entire video I just made so I’m trying to figure out how to backup my phone with out loosing everything else lol. Again, thank you so much for the awesome comments! I won’t let you down!
I have been wanting to do this for quite sometime, and as you stated, I've seen about a thousand of these videos. This, by far, is the best DIY video series on TH-cam. You were made for this, and I wish you all the best in your continued support of helping train all of us DIYers out here on the interwebs. I look forward to your next videos.
Awesome! You made this concrete countertop build simple. Tired of the overly complicated videos out there on TH-cam. Thanks, buddy.
THATS WHAT I’M TALKIN ABOUT! Haha 😆
Loved the simplicity. So many want to complicate things, with intent of promoting outside business profits. Nice that see straight forward, with simple instructions.
Same kind of things I try to do in instructing about electrical work.
Nothing is hard in life when we know how & have an instructor who actually teaches rather than continually showing those learning that they are smarter. Thank you!
DUDE!!! DUDE!!! awesome!! you have so much talent, and to share it with the world is cool.your way of being is appealing and genuine. i hope you become a you tube monster!!! great job! now on my way to depot run!!!
if this indeed your first video then all i can say is you are a natural at presenting. All the power to you brother. I am a fan already.
My man, just did this for an outdoor bar top... Worked like a charm... The worker at Home Depot was saying I needed PSI 6000 because the mortar mix is too weak... Wish I could send him the pictures... Thanks my man, the step by step was amazingly easy to follow... 👍🏼
This is definitely a likeable video. Your sense of humor, and the fact that you went the extra mile to make it entertaining, verses just a how to video, kept me watching and wanting more. I was not at all bothered by the music volume.
awwww! THANK YOU SO MUCH TARA! You just made my day 👍🏻😊
And go Tigers!!!!
Yo...This guy is my new rock star. First video?? Man I couldn’t stop watching. @HGTV you need to give this guy his own show.
Lol 😂 thank you so much Dwayne!!!
Brother I have to say that you did mighty fine work there. I was impressed with your knowledge and work. Keep it up !
i like shortcuts and I usually try and add shortcuts to shortcuts, but I didn't this time and it paid off. This is hands down the best how too video I've seen. I read the reviews on the rapid set mortar mix and almost didn't use the product due to the short work time, but I trusted and followed Mike's instructions. The Flow Control is incredible. Plenty of time to work with it and countertops are looking great. I used some old quarter inch trim moulding I had with Gorilla tape and bypassed the silicone part (impatient and needed to find a shortcut) and and the corners look great. I did a test run with different trims and it's $20 well spent. My wife picked the edge she liked best and I became familiar with process. Used Canola oil spray instead of wd 40 and released easily. Thank you Mike!
Place a board or something similar in from the edge during your live edge chipping, to prevent accidentally going in too far and knocking out too large a chunk.
Leif Hietala or stone chisel
There's No such thing as
mistakes......" just happy little accidents."
The real OG...... B.R.
Really great idea.
You must make a diy wood fire pizza oven!! You are right I’ve watched 100 countertop videos and yours was the best... now do the same for a concrete wood fired pizza oven!!
Lets do it! 👍🏻😉
Depot run!!
back in the 50s used to cast 6" thick cold slabs in the larder. was left for a week to cure with shuttering still in place. motor oil/axle grease was the release agent.
Thanks!
OMG! Wayfinder! I cannot tell you how SORRY I AM that I did not reply to your AMAZING contribution from a whole year ago! TH-cam did not notify me about your SuperChat and I didn't see it until just now while I was stumbling around in my TH-cam analytics. I am so embarrassed and so so sorry man. Please accept my very humbled THANK YOU! You have no idea how much I appreciate your support and I'm even more appreciative that you gave me a SuperChat on this particular video. Even tho this video is my worst video ever (hahaha), it still holds a very special place in my heart because it changed my life. Again, thank you so much!
You Sir, are a natural! I look forward to watching many more of your videos.
Why thank you so much man!
Came across this kind of accidentally, and went from having never, once, ever, even thought about concrete counter tops, to..."I'm doing this immediately!!" Great presentation and tons of info. Subscribed.
we did it and it worked great. So smooth. A lot of work though for a whole kitchen
No Way! First video? Love it! Comical and education is a great combination! Makes it fun to learn. I'll be watching for your next videos.
I made this countertop yesterday. Worked out just like described in the video! Excellent instructions! BTW...the Captain Morgan stance was performed. Made the project go that much more smoothly.
Lol 😂 that’s awesome Kent!
This is the BEST DIY vid on concrete countertops EVER!! Thank you for posting!!
Oh my gosh thank you so much!
Hi Michael-
I saw your videos and got hooked on the idea of concrete countertop for my new house. Had my contactor made the forms ( I don't have a tablesaw) and poured the most beautiful counter tops myself ... I love looking at them! Also made a bench & used rebar for the legs . Thank you for showing me how to be a concrete superstar!!
First video??
Solid editing, not bad music, volume control, steady camera *not* handheld, used a tripod, great topic, super clear instruction, 10/10 end product......
Liar. Impossibru face
Loved this video, watched it over and over, typed up instructions and list of supplies, trying it this week with one of my sons. DEPOT RUN! Boom!!!! What better way is there to spend time with your kids, we both have 1 week vacation time to do this project and others! Hanging out in his workshop all week. Thanks Michael, you are a talented and funny guy.
I love it! Good luck! These kind of comments are my favorite because that’s what it’s all about!
Great video! By far the easiest concrete table instructional I’ve seen yet. You are a natural for showing how things are done. Subscribed.
Love the video. Lots of good information, with more of the tips that you learn from experience. So many people spend a ton of time taking about making a mold, but if we made it this far we know at least how to cut a few pieces of wood. That tip with the spray window cleaner is awesome. You are the only person I have seen do that. Brilliant!!
Thank you so much Nathan! I did my best to give you guys enough bullet points and cool tips to get the job done without spending a ton of time on the project! Thank you so much for watching my video!
to keep your art in place, lightly apply several coats of hairspray over them before you pour the concrete. it will lock the sand in place and will not discolor the concrete.
Great idea!
👍🏼I do that with my chalk art I do on my pavers and wooden front porch and deck .. Helps keep the art around much longer. even when it rains (and I live in Oregon where it rains all the time.) As much as I love mod podge, and as much time as I spend on each piece of art, I want to enjoy it longer than a day or two but don't want it to be a permanent addition. Hairspray works wonders... As well as keeping my gel pen ink in place on plastics, rocks, and other random, non paper items, so I can then use spray mod podge to lock the art in place.
I would have spaced it for something like this project. 👍🏼👍🏼👍🏼👌🏼
trying my hand at concrete and you would not believe how many other videos have referenced your video. very easy to follow and learn
production and editing was top shelf for a newby
Yes, but I beg men to please lower the volume on the music. I had to turn up the volume really loud to hear his voice and that made in damn near painful when the music was playing. :(
He could use some audio compression . Take a look at th-cam.com/video/DYOuClAWokg/w-d-xo.html on how to.
A newby? What a preschooler??? Newby=annoying!
@@margr8218 just shut up. You are annoying=Margaret Rauch
Not even 6 mo's later, over 100k subs. I'd say, people like watching you make stuff!
A couple thoughtful comments
I rarely watch an entire video but fast forward past the BS to get to the info. Your video was good on so many levels I watched the whole thing. That's especially remarkable because I have very little interest in cement counter tops. Making promises at the beginning caused me to want to watch to see how that would turn out and I found the video informative and entertaining. I especially liked 5 gallon bucket cam and pulling nails with your teeth but the best part was knowing all of this was about a friend needing a coffee table. You're a good friend and I really wanted to see you giving your friend the coffee table you made for him.
All of my lavish praise comes at a price - just a suggestion. Tighten it up. There are several minutes that could be cut which would make a really good even better.
Removing rusted nails with your teeth, now that's how it's done! Another awesome build, I need to start stacking wood pallets behind my shed. I just finished a pallet wood crate on casters for raffle at my daughter's school, wish I share/post the pic here.
Creds must be given the your people in the shadows. Your video angles & editing are down to earth and simple. Keep up the great team work!
No one in the shadows here 😉👍🏻. I’m behind the camera and in front of the camera. I did both filming and editing on my iPhone 8. I very good buddy Jordon was definitely there for MUCH moral support and set up everything on social media for me and our video. For that I owe him everything! 😊
I used this method over the weekend to cast a 2' x 8' x 2" outdoor bar top. In general, it worked very well. A couple of notes and other things I learned:
1. If you haven't done this before (I hadn't), and if it's possible with your time or budget or desired level of effort outlay, I would highly recommend a "test cast" of either a full or half bag of mortar in a small mold, before making your finished product. Its really good to get your technique down and practice! A small mold would be about 2'x2'x1.5" which would be a single 0.5 cu/ft bag.
2. I used the WD-40 as recommended, however I forgot to wipe it down before pouring. Turns out this is NOT an optional step. My slab has very evident graffiti-like markings where I sprayed the WD-40. Frankly, the melamine is so slick I'm not even sure this step is needed. Again, a test casting would have found this issue.
3. Make sure whatever structure you are casting on is ROCK SOLID and doesn't allow for any sagging in the mold as the concrete cures. The melamine is surprisingly resistant to deflection but remember that each bag of mix adds 55+ lbs of weight and that adds up quickly. I had a large corner crack off my casting and I attribute that to the mold sagging in the middle over the sawhorses I had it placed on as the concrete cured.
That’s some great info thanks you. How many bags did it take for your pour? And did you put any reinforce it at all
@@garrettsoto1667 Each 55lb bag is .5 cu ft, so I used 4 in total. And i did not use any reinforcement, other than the corner breaking off (which was because the mold sagged while curing) the top is extremely strong.
Gene Dassing thanks for the reply. Did you have to mix up a slurry coat to patch any air holes?
that was amazing, and I can not believe this is your first video either. Great job for the idea, the delivery, the editing and the smile. You are a great asset
i'm sure your cousin is going to be ecstatic when you deliver that bad boy, and what a great gift, also if this is your first video i do believe you are on to a new career.
Your video was a lot of fun and your delivery is easy going and friendly, perfect for any project! Nice job.
REGARDLESS of topic, this has to be one of the VERY BEST VIDEOs on TH-cam. Nooooo shit. Wonderful. Hat's of TO YOU sir.
You just made my day sir!
Best concrete instructional I've seen. I'd love to see how you did the bowl/pot pour; I've struggled to find a way to make a form for that!
That’s a good idea. After I get the next video uploaded, that would be a good mini video! Thank you so much!
Would love to see how you make a integrated sink into the counter !!! Or a double Troff sink
This was one of the best DIY videos that I've seen! Bravo amigo!! Thanks for sharing your knowledge and skills.
First video😲 I've poured concrete since the 70's and that was amazing.
Thank you so much Steve! I wanted to share the new technology in concrete with the world!
@@MichaelBuilds editing that video must have taken longer than making the table. Love the flow when you added it 😁👌Only a concrete guy can appreciate a product like that. Again incredible job with the table and video👍I'm a long time diver and treasure hunter. Check out my videos if I had your editing skills I would be set.
I watched/saved this video about a year ago and I had wanted to have a project to create a concrete countertop. The opportunity finally came up and the results were perfect. The steps you provided were very simple to follow and my new countertop turned out excellent. I have already received several compliments and people can’t believe I made it. Thanks for your video!
THATS WHAT IM TAKIN’ ABOUT!!! That’s what it’s all about man!!! 👍🏻😉☺️🤩👍🏻
I am female and from watching your video, I am sure I could do that.
And I loved your video💚
Thank you so much! I want woman to feel empowered! You got this!
This is one of those you made it look easy videos. I'm sure a lot of work went into it. But it turned out great! A friend of mine needs a countertop and I think I will give this a try. Thank you!
Probably the best how-to video I have ever seen. Cant believe it was your first. Just subscribed. Thanks
Thank you so much Joshua!!!
Today (7.8.24)was the first day I ran into your videos and you nailed it. I know this was five yrs ago so I have a lot of videos to see to catch up to your current ones. I was in the market to build a table ( honey do list) for the holidays.
Great Job…..
I have to say if this is your first video, then where have you been. That was fabulous and well done. You are a master craftsman on a higher level than all else. Keep your videos coming because I want to see more. You are the real deal and a pleasure to watch. I want to see what else you can do. Amazing man, you really rock.
Thanks for introducing this product to me. The fast set time of 2500 psi in one hour is a time saver. I would have never thought it was a CSA cement ! The light color is a bonus for design colors.
I'm surprised they call it Mortar Mix since it has so many other uses. You definitely wouldn't want to use a traditional mortar mix because of the lime content and that it can't be used in thick pours(at least according to Sakrete).
A few Home Depots keep stock on Quikrete concrete countertop bag mixes the last time I checked for about the same cost per pound than the Mortar Mix but I think this might be a better product.
I would have thrown in some 3/8" rebar for some more strength during handling or at least some strips of cement block or brick steel joint reinforcement
I'm not too keen on the WD40 as a mold release because of potential bonding issues with any stains or sealers. WD40 has a lot of VOCs that evaporate and don't leave much oil behind but I'm sure a wipe down with acetone would clean the concrete since you didn't use much. I prefer a furniture type carnuba wax like Johnson's Paste Wax.
Very inspiring. And editing is top notch. Definitely going to do this in summer
Would never have guessed it was your first video - excellent quality, great presentation, and awesome project!
After watching this video I felt confident building a 21’ outdoor kitchen and I needed 7 pieces of different sizes countertops so in order to be able to reuse the Melamine I spray painted the ends of the Melamine so i can reuse to complete my counter tops that I needed. And very nervous at first but luckily everything turned out just fine thank god. The wife is happy and I drink a beer and admire my work. Thank you Michael for making this video and making me look good with the family. Have a great summer because thanks to you my summer is going to be great. Oh and I also made a cap for my fire pit using your method and my fire pit looks awesome thanks again. 👏
Thank you so much. You literally added every single element to this table top that I want for the surprise outdoor kitchen I’m planning on building my husband. The countertop has been the piece that has scared me as I thought I would have to perfectly pour a smooth top directly on top of the grilling station. I feel so much more confident and I get the live edge I want without feeling like I need to buy expensive silicone molds.
Awwwwww! Thank you so much Jennifer! That’s what this channel is all about! 👍🏻😊
Very easy to follow. Thanks for making this. I enjoy watching a lot of these videos but I don't always understand what some of these guys are taking about. I feel pretty confident I could make this now after watching this. I appreciated the step by step without all the technicalities. 👍 I'm excited now. Great job! Looking forward to seeing more of your stuff.
Thank you so much Regina! That means a lot to me because I really want to empower woman with this channel! I want to empower anyone that finds projects like these intimidating
I only need to watch your first video for you to convince me to subscribe. 12,000+ other people think the same thing 😁. Can’t wait to see what you have in store. Keep up the great work!
Just did this project with my son 5 days ago, and it turned out great. I only added 4 quarts of water, 1 bag each of Flow and Set control. I also am going to put my brand on the project after the fact with dye and a stencil. Thanks for the encouragement to do this project.
Great project, easy detailed instructions while being entertaining as well.
Loved the shout out to Bob Ross.
Had some trouble hearing you at times, but thoroughly enjoyed the video ! How about a video showing how to make mold for kitchen counter with sink holes for plumbing ?
Just built my first concrete table top because of this video! Thanks for the easy to follow methods.
Building an outdoor fireplace w/seating area. I was going to buy granite tops for the sitting area ends, but saw your video and decided to do the concrete instead. You saved me hundreds of dollars... Thanks! The video was AWESOME!
This is the best concrete tabletop video i've seen 👍