I just wanted to give a shout out to 1a auto for all of the great work that they're doing. Its tutorials like these that will help educate America sufficient to remove the dependency.
Thank you for this informative video. I was afraid I would need to remove the steering wheel on my '85 Suburban - you've saved me a lot of time and effort.
@Bigjcomeon There would be an issue with the switch, or if the headlight bulbs were replaced you may want to make sure that the correct ones were installed, as that could also create this type of situation. Hope this helps you out.
@jbrockett1 You may want to test the turn signal by putting it on and then testing the socket to see if it has power going to it. I would also check the fuses to see if you have a blown fuse.
@84chevyguy We ordered some new ones for you, they should be back in stock in about 2 weeks. If you haven't, add your email address the the notify me button on the page and the system will email you as soon as they're back in stock to purchase. Hope this helps you out. Have a great day!
@jbrockett1 I would test the socket that the light plugs into to see it it's a bulb issue or possibly a bad socket. If the socket isn't blinking, also test the wire going to it to see if there's power in the wire. if there is and there's no power in the socket, you may have a bad socket. Also check all of the bulbs front and rear to see if any are burnt out.
@84chevyguy We're working on restocking these. If you add your email to the notify me button, you will receive an email when they are back in stock. Here's a link to them on our website. Hope this helps you out. 1aauto.com/1A/turn-signal-lever/Chevy/Beretta/1AZCC00005/334127/1995
It may be similar. The one that we carry is for a 90 Firebird with delay wipers and it's a different part number. Part Number: 1AZCC00003 on our website 1aauto.com. Hope this helps you out. 1aauto.com 888-844-3393
+CHICKEN WING Thanks for watching. If any of our viewers needs to make this repair, we carry the replacement part shown in this video on our website. Here's a link to them.www.1aauto.com/1A/cruise-control-lever/Buick/Century/1AZCC00002?TH-cam&CTA%20Comment&ATony
I was able to pull the switch stick out easy but no luck getting it back in. Internally, will I have to replace the turn signal switch in the steering column because something is not allowing the stick back in?
Hey Mike, I am having a tough time getting the wire to the cruise control getting FISHED up the steering column. I connected it to a ~ 12 gauge wire via taping around the wire. I also greased it with Vaseline. The connector seems to be where it is getting hung up at. Any ideas for success? Thanks,
Awesome ! I have a problem with mine, the wipers only work on 'high speed' mode, the low and intermitent ones are dead. could it be the switch? or Should I look into something else? like fuses, etc... thanx
is there a way i can remove only the end knob which controls the windshield wiper rate/cruise control? Mine is rotated too far forward so I cant see the labels and stuff, but it still somehow works as intended.
I swapped out the stalk with no problem. But now when I "pull" the high-beam, I get no "click" that would normally actuate high/low beams. All I did was insert it normally, same as you. But no high/low beam "click". Not finding where I can fix this...
6 months ago i installed a new cruise switch. lately turning the wpers on and off has been difficult to twist, and today the wipers are stuck on and although i can twist the switch arm, they stay on. is it possible the new switch is faulty, (i notice the switch metal arm plugs into the steering column), or do you think my porblem would actually be the wiper switch mechanism inside the steering column ? (which really looks like a pain to get at. ) thanks for your help. 1990 k1500 chevy 4x4
+N54 Lord It may be a different procedure on your application. We currently do not have an auto repair video for this particular year, make and model, but the parts are the same. Thank you for asking. 1aauto.com
The transmission fluid in it is black and burnt looking but it is running really good still, am i gona need to get the transmission fixed or just replace the transmission fluid?
I have a 92 Cadillac Deville, on the exterior, it looks simular to this, will this stalk work on a Cadillac? It has cruise, wipers, turn signal functions on it. It does say Buick though on here. I know there is some commonality with most GM divisions.
I ordered a new lever for my 1994 Lumina 4 door sedan but unable to remove the old lever from the connection. I have the steering column torn apart. So I'm not sure if you can order the circular round piece with the wiring and the lever itself as one piece and replace it that way?
+Daniel Blair Hello, We may have the turn signal switch for your vehicle. Please check out our website and search using your vehicle info and we may have a video for the switch if we carry it. Thanks! 1AAuto.com
Great video!, my left signal doesn't return on my '94 GMC K1500 I'm thinking it may need a switch. Do you have a video specific to replacing the switch? My truck is a 1994 with TS, wiper, cruise together. 1GTEK19K6RE547820 I keep all maintenance on carfax as well. Just did the waterpump, wipers, tire rotation, alignment. Road trip!
+Scott Feron Thanks for checking us out! We offer the below video for the 1992-99 GMC K1500 combination switch. th-cam.com/video/MwcQCXynKcU/w-d-xo.html
I just received this lever from you guys 1AZCC00002. the chrome "push " lever does not seem to have any "Clicking" or set into the black part with the lettering. Is it supposed to be loose and separate ? The chrome part is not "connected" to the black part, there is no tactile sense of shifting between hi/lo/intermittent/mist. I think I got a defective part?
everything works on mine, but pulling back to switch between high and low beams does not work unless pulling back far and firmly...is there an internal piece that would affect the response of the switch?
+James Kelly This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-1AAuto-c
This looks like the same exact lever as my 1993 Buick Century. Will that lever also work with my car along with cruise control? The website does not have it as a compatible car. The wiring also looks the same
Thanks for watching, we currently do not carry a cruise control switch that would fit your vehicle. The one shown in the video, isn't know to fit this particular year. Thanks for watching. 1aauto.com 866-403-3393
+Gutpunch& HBT This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1AAuto.com
I am trying to do this to my '94 Silverado, but I am not sure which part is the one I need. Wipers erratically work; left turn signal won't turn off and I have to manually do it.
+alwaysopen We currently do not have an auto repair video on this particular year, make and model. It might be a similar process. If any of our viewers needs to make this repair, we carry the replacement turn signal switch shown in this vide on our website. Here is a link to them www.1aauto.com/cruise-control-lever/i/1azcc00002#TH-cam&CTA%20Comment&
If you visit our website at 1aauto.com you can look up your year, make, model and series to find the correct one for your vehicle. Hope this helps you out.
Yes I have a probablem My blinkers don't work only the hazards work I replaced the turn single part and they still don't work I have a 2000 dodge dakota v6 truck eny help please thanks :)
HI Jim, It is Part Number: 1AZCC00002 if you click on the link in the video, it will also bring you to the auto part being installed in our video, to our website where it's also for sale. Hope this helps you out. 1aauto.com 888-844-3393
I have an 89 firebird and when i pull back the bright light switch it doesnt click and stay back and i also noticed that a little rod is loose by it??? How di i fix it?
'89 Trans Am... Wipers only work when the "washer fluid" tab is held. Hi/Lo beam does not work. The "stalk" is quite loose and wobbly. Would a new "stalk" fix the wiper and hi/Lo beam problem?
HI Chad, It sounds like the stalk may be bad. If it's not working correctly, replacing it may get all of you functions back in working order for you. We carry new turn signal switches on our website. We also offer FREE SHIPPING in the lower 48 states. 1aauto.com 888-844-3393
I pulled the stalk out. It's brand new. In fact, whoever replaced it just ran the wire on the outside of the column. It appears that the place the stalk pushes into (inside the column) is broken. What is THAT part called?
Chad Conrad It sounds like you're talking about the turn signal switch. We carry new ones on our website 1aauto.com for a Pontiac Trans Am without steering wheel controls. Part Number: 1AZTS00018 888-844-3393
+CHARLIE BROWN Thank you for checking us out. This could be a fuse, a relay, or some wiring going to the rear brake lights. It could also be the rear junction block. 1aauto.com
i replaced my switch, but the cruise button keeps popping out and the switch doesnt click when i twist it, it just free spins until the wire stops it. is there something else that could be bad?
+kaui chu We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com
+Sammy Torres You should do some research on locating, diagnosing and resolving electrical shorts. Basically, the idea is that you follow the wires from the switch to where ever they're getting power or otherwise grounding and look for breaks in the electrical insulation where they may be shorting out against other metal or other worn out wires.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
I just wanted to give a shout out to 1a auto for all of the great work that they're doing. Its tutorials like these that will help educate America sufficient to remove the dependency.
Thank you for this informative video. I was afraid I would need to remove the steering wheel on my '85 Suburban - you've saved me a lot of time and effort.
Saved me from removing the steering wheel and column, thanks to your video.
Thank you for visiting our channel on TH-cam, we currently do not have an auto repair video that shows this particular repair.
@ComPrt3 Awesome! Thanks for checking out our auto repair channel on youtube. Have a great day!
You may want to check the brake light switch to see if it's working correctly. If it's bad it may also correct the turn signal issue.
You're welcome. Have a great day. Thanks for watching out video.
@Bigjcomeon There would be an issue with the switch, or if the headlight bulbs were replaced you may want to make sure that the correct ones were installed, as that could also create this type of situation. Hope this helps you out.
@jbrockett1 You may want to test the turn signal by putting it on and then testing the socket to see if it has power going to it. I would also check the fuses to see if you have a blown fuse.
Just what I needed for my 1987 GMC Classic Sierra. Haven't tried it yet, but will soon.
+Dan Dehnke Thanks for checking us out. 1aauto.com
If you have a test light, test the wire going to the sockets to see if there's power to the sockets when you step on the brake.
@siggersd That would be the wiper switch. We carry them for many different vehicles on our website 1aauto.com
@Darb071 That application looks as though it uses a different style of switch. The basics might be similar.
@84chevyguy We ordered some new ones for you, they should be back in stock in about 2 weeks. If you haven't, add your email address the the notify me button on the page and the system will email you as soon as they're back in stock to purchase. Hope this helps you out. Have a great day!
@ComPrt3 Your 89 Chevy Caprice uses the same turn signal lever. The video should be the same for your vehicle. Hope this helps you out.
Might be that, or you may want to check the fuse and the wiring to see if the bulbs have power to them.
@jbrockett1 I would test the socket that the light plugs into to see it it's a bulb issue or possibly a bad socket. If the socket isn't blinking, also test the wire going to it to see if there's power in the wire. if there is and there's no power in the socket, you may have a bad socket. Also check all of the bulbs front and rear to see if any are burnt out.
@jshedivy That function is part of the switch also, and could wear out.
We currently do not carry a turn signal lever for this application. It might be a similar process.
We currently do not have an auto repair video that shows this particular part. We'll keep this request in mind during any future repairs.
@84chevyguy We're working on restocking these. If you add your email to the notify me button, you will receive an email when they are back in stock. Here's a link to them on our website. Hope this helps you out. 1aauto.com/1A/turn-signal-lever/Chevy/Beretta/1AZCC00005/334127/1995
We currently do not have one listed for that particular vehicle. The one shown in the video is different.
If ti's broke and needs to be replaced we carry new ones on our website 1aauto.com 888-844-3393
Thanks, I just purchased a switch from you for a caprice :)
@1aauto Worked like a charm. Thanks
The switch in your link is all black and shaped slightly different but the one in the video has a chrome washer switch which is the one I need.
It may be similar. The one that we carry is for a 90 Firebird with delay wipers and it's a different part number. Part Number: 1AZCC00003 on our website 1aauto.com. Hope this helps you out. 1aauto.com 888-844-3393
If the new switch is hard to turn and not is not changing the settings over, then you will have to probably replace the switch again.
The turn signal multi-function switch could be bad. We carry new ones on our website, if you need to replace it. 1aauto.com 888-844-3393
perfect instructions..thank you!!
I enjoyed watching this video.
+CHICKEN WING Thanks for watching. If any of our viewers needs to make this repair, we carry the replacement part shown in this video on our website. Here's a link to them.www.1aauto.com/1A/cruise-control-lever/Buick/Century/1AZCC00002?TH-cam&CTA%20Comment&ATony
I was able to pull the switch stick out easy but no luck getting it back in. Internally, will I have to replace the turn signal switch in the steering column because something is not allowing the stick back in?
@SrCajita It sounds like it could be the switch.
So do I have to remove the steering column on a 92 cutlass supreme to change the wire harness with it, the 13 pin connector
Hey Mike,
I am having a tough time getting the wire to the cruise control getting FISHED up the steering column. I connected it to a ~ 12 gauge wire via taping around the wire. I also greased it with Vaseline. The connector seems to be where it is getting hung up at. Any ideas for success?
Thanks,
The replacement between the two vehicles are going to be similar.
Great video. I have an unrelated question. How would I remove the fuse box on 1991 gmc Jimmy SLE? Thank you in advance.
Awesome ! I have a problem with mine, the wipers only work on 'high speed' mode, the low and intermitent ones are dead. could it be the switch? or Should I look into something else? like fuses, etc... thanx
I would replace ALL of the fluid in the transmission and put a new filter in it.
is there a way i can remove only the end knob which controls the windshield wiper rate/cruise control? Mine is rotated too far forward so I cant see the labels and stuff, but it still somehow works as intended.
I swapped out the stalk with no problem. But now when I "pull" the high-beam, I get no "click" that would normally actuate high/low beams. All I did was insert it normally, same as you. But no high/low beam "click". Not finding where I can fix this...
There's a rod for the high beams in the column that you might have to reattach. You'd have to pull the wheel and lock plate to get to it.
6 months ago i installed a new cruise switch. lately turning the wpers on and off has been difficult to twist, and today the wipers are stuck on and although i can twist the switch arm, they stay on.
is it possible the new switch is faulty, (i notice the switch metal arm plugs into the steering column), or do you think my porblem would actually be the wiper switch mechanism inside the steering column ? (which really looks like a pain to get at. )
thanks for your help. 1990 k1500 chevy 4x4
Great job...is this the same process for 89 Buick century? Handle looks the same.
+N54 Lord It may be a different procedure on your application. We currently do not have an auto repair video for this particular year, make and model, but the parts are the same. Thank you for asking. 1aauto.com
@@1AAuto thanks!
I'm about to order a new wiper/cruise arm from you, this video looks similar to what I have. 1987 S10 Blazer. Is the replacement process the same?
The transmission fluid in it is black and burnt looking but it is running really good still, am i gona need to get the transmission fixed or just replace the transmission fluid?
It could be worn out, you might need to replace the switch.
The brake light switch is good i changed it just 2 days ago.
I have a 92 Cadillac Deville, on the exterior, it looks simular to this, will this stalk work on a Cadillac? It has cruise, wipers, turn signal functions on it. It does say Buick though on here. I know there is some commonality with most GM divisions.
If you take the plastic cap off behind the switch there's a plug there. The cover snaps on.
+CR7659 Thanks for the tip!
I ordered a new lever for my 1994 Lumina 4 door sedan but unable to remove the old lever from the connection. I have the steering column torn apart. So I'm not sure if you can order the circular round piece with the wiring and the lever itself as one piece and replace it that way?
Do you have a tutorial for removal and replacement of the hi/lo beam switch?
+Daniel Blair Hello, We may have the turn signal switch for your vehicle. Please check out our website and search using your vehicle info and we may have a video for the switch if we carry it. Thanks!
1AAuto.com
Is it possible to swap this with the one without cruise control...since the engine was swapped?
Great video!, my left signal doesn't return on my '94 GMC K1500 I'm thinking it may need a switch. Do you have a video specific to replacing the switch? My truck is a 1994 with TS, wiper, cruise together.
1GTEK19K6RE547820 I keep all maintenance on carfax as well. Just did the waterpump, wipers, tire rotation, alignment. Road trip!
+Scott Feron Thanks for checking us out! We offer the below video for the 1992-99 GMC K1500 combination switch.
th-cam.com/video/MwcQCXynKcU/w-d-xo.html
I just received this lever from you guys 1AZCC00002. the chrome "push " lever does not seem to have any "Clicking" or set into the black part with the lettering. Is it supposed to be loose and separate ? The chrome part is not "connected" to the black part, there is no tactile sense of shifting between hi/lo/intermittent/mist. I think I got a defective part?
everything works on mine, but pulling back to switch between high and low beams does not work unless pulling back far and firmly...is there an internal piece that would affect the response of the switch?
where are you taking the lead wire from? I cant find information on where the multi-function wire plugs up to
Iv pulled on my lever pretty hard it want come out any suggestions
Would This procedure be the same on a 1994 Chevy s10 manual transmission base model?
+James Kelly This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1aau.to/m/Shop-1AAuto-c
I have 1985 c10 Chevy need help on how to change the light dimmer switch I believe it with the turn signal stick neeh your help thanks.
This looks like the same exact lever as my 1993 Buick Century. Will that lever also work with my car along with cruise control? The website does not have it as a compatible car. The wiring also looks the same
Thanks for watching, we currently do not carry a cruise control switch that would fit your vehicle. The one shown in the video, isn't know to fit this particular year. Thanks for watching. 1aauto.com 866-403-3393
Is this the same way to fix one of these switches on 1987 monte Carlo ls ? PLEASE
RESPOND AS SOON AS YOU
CAN THANK YOU.
+Gutpunch& HBT This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1AAuto.com
@@1AAuto Ok thanks for
Your quick response I've
Got your message .
Been watching vids trying to figure out where the black cruise wire plugs in under dash
i am doing the same to my 1990 firebird is it the same thing to replace it :)
I am trying to do this to my '94 Silverado, but I am not sure which part is the one I need. Wipers erratically work; left turn signal won't turn off and I have to manually do it.
What do you do if you've replaced the switch and now your wipers don't work? My cruise control wires were cut and that's why I replaced the switch.
I have a 1993 c1500 w/o CC, do I need to play with the wire to change the stalk? The spray section is cracked and that's it.
+alwaysopen We currently do not have an auto repair video on this particular year, make and model. It might be a similar process. If any of our viewers needs to make this repair, we carry the replacement turn signal switch shown in this vide on our website. Here is a link to them www.1aauto.com/cruise-control-lever/i/1azcc00002#TH-cam&CTA%20Comment&
@1aauto i did i replaced the whole part of the blenkers and the hazzerd switch and they still dont work and the fuses work i checked them
So how do you get it down through there if you break your wire
I got a 91 Silverado that needs a new switch would that work as well or would it be one of the other videos I have seen from you guys?
If you visit our website at 1aauto.com you can look up your year, make, model and series to find the correct one for your vehicle. Hope this helps you out.
how do you put the actuator in a 92 van so the high beam works
Yes I have a probablem My blinkers don't work only the hazards work I replaced the turn single part and they still don't work I have a 2000 dodge dakota v6 truck eny help please thanks :)
We currently do not have an auto repair video that shows this particular repair. 1aauto.com 888-844-3393
@1aauto ok got my email in there thanks for letting me know... hope u restock them soon...
My 1990 chevy turn signal or brake light dont work. But hazard lights work and all light work and Fuses is good. Whats the problem?
what would help me is if ur 95 beretta turn signal lever was in stock....?
Would this work for a 1989 Chevey Caprice?
Mine broke off with a piece stuck inside any idea how to get the little piece out
The brake switch is good i just changed it so what can it be
Actually the Saginaw column and parts are interchangeable from the 60's to current.
Can you show the clip where it needs to plug
I need this lever but for a 1982 gmc sierra pick up
HI Jim, It is Part Number: 1AZCC00002 if you click on the link in the video, it will also bring you to the auto part being installed in our video, to our website where it's also for sale. Hope this helps you out. 1aauto.com 888-844-3393
hey how do i change the switch ignition for a 85 cutlass salon
I have an 89 firebird and when i pull back the bright light switch it doesnt click and stay back and i also noticed that a little rod is loose by it??? How di i fix it?
You bad sis thank you
+Christopher Murphy Murphy Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c
'89 Trans Am... Wipers only work when the "washer fluid" tab is held. Hi/Lo beam does not work. The "stalk" is quite loose and wobbly. Would a new "stalk" fix the wiper and hi/Lo beam problem?
HI Chad, It sounds like the stalk may be bad. If it's not working correctly, replacing it may get all of you functions back in working order for you. We carry new turn signal switches on our website. We also offer FREE SHIPPING in the lower 48 states. 1aauto.com 888-844-3393
I pulled the stalk out. It's brand new. In fact, whoever replaced it just ran the wire on the outside of the column. It appears that the place the stalk pushes into (inside the column) is broken. What is THAT part called?
Does the wiper switch (inside column) also activate the hi/lo beam?
Chad Conrad It sounds like you're talking about the turn signal switch. We carry new ones on our website 1aauto.com for a Pontiac Trans Am without steering wheel controls. Part Number: 1AZTS00018 888-844-3393
Where does it plug in?
It could be a bad switch.
my 94 GMC suburbon's brake lights don't work. I've changed the brake switch cruise works and will deactivate ,but no brakes. please help.
+CHARLIE BROWN Thank you for checking us out. This could be a fuse, a relay, or some wiring going to the rear brake lights. It could also be the rear junction block. 1aauto.com
i replaced my switch, but the cruise button keeps popping out and the switch doesnt click when i twist it, it just free spins until the wire stops it. is there something else that could be bad?
+kaui chu We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com
How to replace turn signal wiper stalk cruise lever for Chevy caprice 95
What is the part number on your website?
would this work on a 94 blazer full size
Thank you for watching. The process may be a little different. We will keep this vehicle in mind for future videos.
1aauto.com 888-844-3393
my washer lever broke in my 92 chevy truck how do i can replace it
i have a 1984 C10 and when i switch the blinker to go left it hobks the horn please help
how would i know were the problem is if i follow the wires?
+Sammy Torres You should do some research on locating, diagnosing and resolving electrical shorts. Basically, the idea is that you follow the wires from the switch to where ever they're getting power or otherwise grounding and look for breaks in the electrical insulation where they may be shorting out against other metal or other worn out wires.
Every time I turn on my signal light it won't blink. I checked the fuse but that's not the problem.
Could also be a bad flasher
good questian i ramirez thats what im here for my cheap control stick broke on my 1992 lesaber
O wait its cool
I have a 2001 z28 and my brights don't work because of the stalk beeing loose? what do I do?