LG/Kenmore Front Load Washer Pump Motor

แชร์
ฝัง
  • เผยแพร่เมื่อ 23 ธ.ค. 2024

ความคิดเห็น • 53

  • @JandSParr
    @JandSParr 9 ปีที่แล้ว +9

    Perfect. Very helpful. We didn't believe it would take only 45 minutes to replace the motor. The most challenging part was replacing the spring without the tool. Otherwise a perfect detailed video. Thank you!!

    • @sandspringsgirl
      @sandspringsgirl 8 ปีที่แล้ว +3

      Yeah, the spring is a booger, lol. Finally got it by using a flat head screwdriver and "prying" around the edges to make it go on.

    • @mpeg12
      @mpeg12 9 หลายเดือนก่อน

      ​@@sandspringsgirlplease explain further. I'm stretching it with pliers and levering it with screwdrivers and only managing to scratch the paint. Argh.

  • @sandspringsgirl
    @sandspringsgirl 8 ปีที่แล้ว

    Ordered the part from Repair Clinic almost midnight Monday, had part by noon Thursday (today), followed directions on video, now have working washing machine, thank you God! Repair Clinic is highly recommended, was a factory LG replacement part for my LG washer. Just a tad different from video (which shows a Kenmore). Thank you so much for the step by step video and thank you to my husband for doing the work! Took about an hour.

  • @kennethmadl1728
    @kennethmadl1728 ปีที่แล้ว

    My Pump mounting has three 10mm hhcs bolts holding the pump to the base and 5 Philip’s head screws, holding the pump to that plate. I had to disconnect 3 hoses to get the pump out. There are no screws to remove for my control panel. It just snaps in and out.
    For the record this video made it easy for me to get through to be able to identify my differences, so I am thankful!!

  • @hahahahagrin
    @hahahahagrin 10 ปีที่แล้ว +1

    This video was outstanding and was instrumental in helping me do the job myself. The pump replacement was easy and saved me literally hundreds of dollars. Note that after the pump replacement, I got an "IE" error. By coincidence only I presume, it was a water INLET error. Found the filter on the washing machine COLD water intake valve clogged due heavy mineral water we use. Cleaned delicate filter with took pick...and all is well!! Thanks for such a great video.

    • @repairclinic
      @repairclinic  10 ปีที่แล้ว

      That's great! Good job! Thanks for the comment.

  • @ParkerMuirhead
    @ParkerMuirhead 2 ปีที่แล้ว +1

    Parts were slightly different on my Kenmore washer but this video helped a ton. Well laid out and explained everything you need to know.
    Only thing to note is if you don't have a spring expansion tool it's a pain to get the boot back on. I used a wrench and some zip ties to get it back on.

  • @nobodymatters3294
    @nobodymatters3294 ปีที่แล้ว +4

    I can not recommend this company enough. They are awesome too work with. ⭐⭐⭐⭐⭐

    • @repairclinic
      @repairclinic  ปีที่แล้ว

      You're welcome!
      If you would like to give us a review, here is our link: g.page/r/CcVUrahZNozMEBM/review
      Have a great day!

  • @32fordcoupegirl
    @32fordcoupegirl ปีที่แล้ว +1

    I AM JUST ABOUT TO GO THRU THIS AND THIS VIDEO MADE IT CLEAR ! THANK YOU

    • @repairclinic
      @repairclinic  ปีที่แล้ว

      You're welcome!
      If you would like to give us a review, here is our link: g.page/r/CcVUrahZNozMEBM/review
      Have a great day!

  • @VaraGirl
    @VaraGirl ปีที่แล้ว +1

    Thank you so much for your wonderful tutorial video. I was able to do everything, except when I went to put everything back, the door is not latching shut anymore. It is not catching. I had a heckuva time getting the wire connector unlatched from the door, so maybe broke it? Are the sensitive? What could I have done wrong? Do I need to buy a new door latch now? Should I just try to unplug door latch connector again and plug it back in? Any tips would be appreciated.

    • @mpeg12
      @mpeg12 9 หลายเดือนก่อน

      I found that removing the two screws holding the door latch was easy -- after giving up on pulling the door latch connector.
      You might've broken the connector or its wires. An ohmmeter can be useful to check the connections if you can access the other end of the cable. Or remove it via the screws and examine it closely.

  • @brianwnc8168
    @brianwnc8168 7 หลายเดือนก่อน +2

    It's a lot easier just to tip the washing machine and take the pump out from the bottom. If you don't mind laying on your back for a few minutes while doing the work. Saved me a ton of time versus following these instructions

  • @devinthomas4866
    @devinthomas4866 6 ปีที่แล้ว +1

    LG washer with OE code
    Would not drain , cycle interrupted
    Cleaned all filters and tubes, no luck
    Sounded like pump not working or at least having trouble pumping water
    Ordered new LG pump
    followed excellent video instructions
    test wash cycle running now, sounds great already
    cleaned the recirculate side and yellow spray nozzle at top of drum
    also cleaned 6 oclock drain in the rubber gasket and cleaned the outlet, lots of buildup
    black drain hose was completely clogged with black gritty mess, my guess is this is what burned out pump
    Thank you for great information

  • @dnohseek
    @dnohseek หลายเดือนก่อน

    2:21 Be aware that many similar models have a separate re-circ pump located on the right side of the pump housing as shown.

  • @repairclinic
    @repairclinic  9 ปีที่แล้ว +1

    Gat Parker, In most cases you can reverse the wires on two wire motors that use AC voltage and it will still run properly.

    • @sweetverdugo2926
      @sweetverdugo2926 หลายเดือนก่อน

      Does it matter where the wires connected to pump?

  • @repairclinic
    @repairclinic  11 ปีที่แล้ว

    No problem! We're happy we could help!

  • @YeeCente
    @YeeCente 2 ปีที่แล้ว +1

    Hi! I’m at the 2:42 mark and my kenmoore filter is attached to a metal bracket? Do I remove that instead? Or is there still a clip/latch? Thank you in advance!

    • @jaredvahl9142
      @jaredvahl9142 2 ปีที่แล้ว +2

      Same situation I'm in right now... did you figure out a solution?

    • @YeeCente
      @YeeCente 2 ปีที่แล้ว +1

      @@jaredvahl9142 yeah, unfortunately youve got a little more work, but there’s 3 bolts or so you have to remove. You’re almost at the finish line!

    • @jaredvahl9142
      @jaredvahl9142 2 ปีที่แล้ว +1

      Got it. 10mm socket with an extension and a ratchet

    • @loriburns6906
      @loriburns6906 ปีที่แล้ว +1

      Victory at last!

  • @drewthompson7457
    @drewthompson7457 4 หลายเดือนก่อน +1

    Just something to add. The pump on my LG is half magnet, so the rotor turns in jumps, and might appear to be sticky with debris. I took it out of the unit only to find it had no problem. I have a washer / dryer unit, and the problem was built up debris in the dryer parts.

    • @repairclinic
      @repairclinic  3 หลายเดือนก่อน

      Thanks for the tip.

  • @rglemois
    @rglemois 2 ปีที่แล้ว

    Thank you for posting. Easy peasy. Back in service.

  • @johneldredge2970
    @johneldredge2970 11 หลายเดือนก่อน +1

    Some units have bottom access that is a bit less complicated.

  • @loriburns6906
    @loriburns6906 ปีที่แล้ว +1

    I am stuck on the step where I'm supposed to push the tab on the pump housing to release the pump housing. It's like it's sitting on a metal ledge. No tab to push. Stuck here without trying it on its back and taking a bunch of other screws out. There's got to be an easier way. Mine is a Kenmore. All steps were the same until this step. Help!

  • @acesventura
    @acesventura 12 ปีที่แล้ว +1

    Could never have done this without this video. Awesome step by step instructions. Thank you.

    • @mayrabadillo6987
      @mayrabadillo6987 2 ปีที่แล้ว

      Hello I removed the drain pump but now the washer machine does not fill with water. I verified the hose, filter, water pressure etc. Please advice

  • @jimt7786
    @jimt7786 6 ปีที่แล้ว +2

    Is this Video applicable to this LG Model WM3470HWA? I followed all instructions from the video and already remove the front panel but to remove, and snap out the pump assembly from the washer my model is different from what I see in the video, It doesn't have the 2 screws near the drain tube I dont see or feel a holding tab so I can remove the pump I do so a metal frame connected with 3 Flange Bolts screws on the matal frame and I am not sure if I do need to remove it

    • @YeeCente
      @YeeCente 2 ปีที่แล้ว

      Same thing happened to me. Did you figure it out?

  • @dan0368
    @dan0368 ปีที่แล้ว

    Phenomenal video, I'm a boob and was able to do this in a hour or so.

  • @perrykuhnen1162
    @perrykuhnen1162 2 ปีที่แล้ว

    Great explanation. I went to order this part from your site and at checkout was told that part couldn't be shipped to Canada 😞

  • @gloria421
    @gloria421 ปีที่แล้ว

    My front load opensfrom the bac, not the top, I have a Kenmore front load whirlpool & it dose not in spin or agitate anymore, nither does the timer relay go to O ,keeps on ruining .will not stop doing the same thing until I cancel manually.ty...please help!!!! Would that have anything to do with the MOTOR??

  • @kristiannielsen6013
    @kristiannielsen6013 3 ปีที่แล้ว

    Thank you! This saved me a ton of money!!!

  • @seanballington9558
    @seanballington9558 9 ปีที่แล้ว

    Great video - I used it to replace the pump and the pipe - great directions.

    • @repairclinic
      @repairclinic  9 ปีที่แล้ว

      Sean Ballington We appreciate your feedback.

  • @SevereUwu
    @SevereUwu 4 หลายเดือนก่อน

    What happens if i connect the pump motor wires wrong?

  • @CFJohnhable
    @CFJohnhable 9 หลายเดือนก่อน +1

    Great video. Thank you

    • @repairclinic
      @repairclinic  9 หลายเดือนก่อน

      You're welcome!
      We are always happy to help. If you would like to give us a review on Google, we would much appreciate it: g.page/r/CcVUrahZNozMEBM/review
      We hope that you have a great day!

  • @graysonsmith3563
    @graysonsmith3563 2 ปีที่แล้ว

    I replaced my drain pump and checked that all the lines are clear but it still won't drain. I can hear and feel that the drain pump is running but it just wont drain. Any ideas?

  • @AustinG073
    @AustinG073 6 ปีที่แล้ว

    Excellent instruction video

  • @rodn3yp
    @rodn3yp 10 ปีที่แล้ว

    Mine is giving me an "OE" code and wont drain. I hear the pump working. Just dont know if thats the problem.

  • @donwilliams1217
    @donwilliams1217 12 ปีที่แล้ว

    Great directions. It took about 20 minutes to repair my machine. Too bad there isn't any videos on how to replace the main pump of a Bosch dishwasher.

  • @amberwrinkle2227
    @amberwrinkle2227 8 วันที่ผ่านมา

    "Detach the control panel mounting tabs, and move the panel out of the way." You make that part look too easy

    • @amberwrinkle2227
      @amberwrinkle2227 8 วันที่ผ่านมา

      Not to sound ungrateful, sorry. Thanks for the clear instructions! Very helpful!