LG Washer OE Error Code - LG Washer Not Draining Fix - LG Washer Drain Pump Replacement Tutorial
ฝัง
- เผยแพร่เมื่อ 24 ก.ค. 2024
- LG Washer OE Error Code - LG Washer Not Draining Fix - LG Washer Drain Pump Replacement Tutorial
Parts used in this video:
LG Replacement Pump: amzn.to/2WWKlFJ
Spring Expansion Tool: amzn.to/380UFmg
When you see the OE error message on your LG washer, that pretty much means there's something wrong with your drain pump. Mine suddenly isn't pumping water out and there's a weird noise when it should be draining. So in this video I'll walk you through detailed step-by-step instructions on how to replace the drain pump on an LG front loading washer! And I encourage you to watch the whole video before beginning your own repair so you're familiar with the process.
To start out, unplug the washer. There are two brackets in the back of the washer that need to come out. But using a short stubby Philips screwdriver helped me get these screws out even though there was very little space to work with. With both brackets out, the top off by sliding it back and lifting it off. Next slide the detergent tray out and remove it.
For the front control panel there are three screws that need to come out. The first two are at the detergent tray opening. The third screw is actually on the inside on the right. Now the front panel can be lifted off. Next keep a towel handy and open the front panel door and drain the water out of the rubber tube into a casserole dish. When all the water is out untwist the coin basket and remove the drain door. Now take out the screw that holds the inner cover on. This will just lift right out. Then take out one last screw in the sheet metal.
Now take out the retaining ring that goes around the big rubber seal. At the bottom there's a spring holding the tension of the ring. To remove it, wedge a screwdriver under the spring and start pulling the ring out of the rubber seal. Then detach the rubber seal from the opening of the washer. On the door latch remove the two screws that hold it on. This will actually detach it from the front of the washer.
Next take out the six screws holding the front of the washer on. And there's actually quite a few things that have to be removed before actually getting to the pump itself. This will be easier to see when watching the video. When the front of the washer is loose just tilt it back a bit and it can be lifted out. But be careful when grabbing it because there are definitely sharp edges on the metal.
You are now at the stage where you can access the pump. Please refer to the video for pump removal. It isn't easy to describe without visual help. When I get the pump out right away I can see that the impeller has broken completely off the pump shaft so this definitely has to be replaced. I had ordered a new pump ahead of time from Amazon and I recommend you do the same before you start your own repair.
The LG washer OE error is caused directly from a damaged pump. With a damaged pump the water won't drain out of the washer and sometimes it will create unusual sounds from inside the washer. There are wires and tubes that need to be removed which is why you'll have to watch the video for the complete repair.
The very last step in the drain pump repair is to put the retaining ring back on. And it's easily the most frustrating and most difficult part. I tried to do it by hand and using screwdrivers many times but could not get it back on. I've seen some videos that make it look easy but the spring on the ring is extremely tight. So I recommend ordering a spring expansion tool before you starting this repair. I paid $12 for it.
If I didn't have this spring expansion tool, I think it's impossible to put the ring back on without injuring fingers or damaging the rubber seal. This tool is definitely a life saver because that spring is super tight and I didn't have anything around the house that could stretch this out. In under 10 seconds with this tool the ring is back on and this repair is complete! My washer now works like normal and water is pumping out just like before. I've listed the $25 pump and $12 expansion tool at top of the description so it's easy for you to find. Hopefully you can see that this is a repair that you can actually do yourself. There's no need to call a repairman.
If you found this helpful please give me a thumbs up and hit the subscribe button for more videos like this! Thanks for watching!
Disclaimer: As an Amazon Associate I earn from qualifying purchases.
***Equipment I Use For My Videos***
Canon EOS M6: amzn.to/2pwQ0Vq
Canon EF-M 22mm f/2 Lens: amzn.to/31mLfLq
Tokina 11-16mm Wide Angle Lens: amzn.to/33TFaYH
Fotodiox EF to EOS M Lens Adapter: amzn.to/31u3AGq
Comica CVM-WM300A Wireless Microphones: amzn.to/31tbiAD
Aputure Amaran AL528W LED Light: amzn.to/2VRuwyK
Kamerar SD-1 Camera Slider: amzn.to/2VUB5Ax
AVermedia HDMI Game Capture Module: amzn.to/31phsSp - แนวปฏิบัติและการใช้ชีวิต
I wish everyone who posts "how to" videos would watch this one first! Very, very professional! Instructions were very clear, camera work and lighting were excellent, audio was excellent. You must have taken a lot of time to produce this. It was a pleasure just watching you do this project. So organized. Learned a lot from your technique. Thanks
You’re welcome! This video did take me a long time to shoot it. I wanted to show every part I was removing so it’s clear how to do this repair. I also had to stop and wait 2 days for the spring expansion tool to arrive. I initially tried to do this without the tool. Then I had to tell viewers that the tool is absolutely necessary to finish the job. Thanks for watching!
Thank you very much for this instructional video. Easy to follow!
Awesome video. Thank you.
Yes awesome video! Thank you for your help
As a retired television production teacher I appreciate the quality of your work. Great job plus you solved my washer problem.
Glad you got your washer fixed! I’m actually a professional broadcast video producer. Been in television almost 30 years! But I still remember my video instructor in college say “television is the medium of close ups”. These days I say “video is the medium of close ups”. That line is one of the main factors I take into consideration when I shoot my videos. I like to show the process up close (using a macro lens if necessary) to show in detail what I’m shooting so the viewer can follow along as if they are looking through my eyes. Especially with tutorials! I want to show each step with as much detail as possible! Thanks for watching!
THANK YOU! As a single female, home repairs are always a stress point. I watched your video over and over as I was doing it. Not as easy for me but still completely doable. I'm proud of myself for not being afraid to try, completing it and having the confidence to do it again should I need. Again...thank you for making this easy to follow.
You’re welcome! I enjoy hearing how people are able to fix their washing machine after watching my video. This is definitely an involved process but I tried to show it step by step to make it easy to follow along. So glad you were able to do it yourself and save money! Thanks for watching!
Same here!!!! I'm trying to figure this out!!!! Thanks for giving me hope!!!!!
All of the other women In my family laughed when I said I was going to do this myself!! You made this super easy and I am washing my first load now and it’s super quiet!!! Thank you for this video!!
You’re welcome! Wow! I’m glad you were able to show them you could do it yourself! Nice work!
I'm a 59yr old mother of five and Nana of four, and I just fixed my washer all by myself! thanks to you!
Excellent! Thanks for sharing your success story of repairing your washer! Glad you saved money doing it yourself! Thanks for watching!
This is how you make a how to do it yourself video....straight to the point...detailed....easy to understand ...clear and articulately said. Thank you very much sir !
You’re welcome! I’m really glad my washer pump replacement video helped! This video is a bit longer than my usual videos but was necessary to show the whole process! I never add unnecessary content and my viewers definitely appreciate it! Thanks for watching!
This is the definitive video to repair this issue with LG washers. I'm on my third drain pump now and simply followed the instructions with the parts from Amazon and we're back in business. A big thumbs up on this video!
I just replaced the pump using your instructions and have to agree with all the positive comments. You saved me money, aggravation and likely also injury....This is the best "how to" video I have used, if there was an Oscar for "how-to" youtubes I'd totally support nominating you!
Excellent! I’m really glad to hear you were able to repair your washer yourself and save money! It’s not too hard to do once you see the process! Thanks for watching!
I just did this repair. This is absolutely one of the best "how to" videos I have ever watched and used. I could not have replaced the defective water pump in my LG washer without first watching Nico's video.
My model LG washer is a WM8000HWA. I would add one additional recommendation: be sure to note (and mark) the orientation of the pump to the pump assembly before unscrewing and removing the pump itself from the assembly. This is at 5:35 of the video. On my pump assembly, the new pump can be reinstalled in a variety of different orientations so this will ensure you don't install it at the wrong angle.
Don't be afraid to do this repair - this video is very accurate and makes it clear on what to do. You will save a lot of money and time. And do follow Nico's excellent hints too! Thank you.
Excellent advice on marking the pump orientation before removing it. I made a mention to take note of that but physically marking it with a sharpie is a fool proof method because the pump does have to be attached in a specific way. I made a mental note and I knew I had my video footage to rely on. But thanks for your tip which I’m sure will help others!
Is your washer the same as the one of the video?
Mine is it I’m trying to get the model to order the pump
Oh, and dont leave your work light inside when attaching front cover. :-) (Yes I did. Only started the second screw, but I did.)
I made the mistake of not marking the orientation but you can use the witness marks from the screws to get it lined back up correctly.
Hands down, the best video on TH-cam for this repair. Enabled me to quickly pull the machine apart, diagnose the trouble and make the repair (especially the PRO TIP on how to re-install the bellow). Many thanks.
You’re welcome! Glad my video tutorial helped! I tried to make it as detailed as possible in case I had to do this repair in the future! Thanks for watching!
This was so helpful in fixing my washing machine. You walked me through tearing apart the machine, fixing the issue and walked me back out putting it all back together again. I was going to have my husband fix it but once I watched the video I said “I can do this with this guys help!” Thank you for taking the time to video this tutorial!
Great work trusting yourself to do this repair! It helps to view all the steps beforehand! It can seem intimidating with all the parts that come out but staying organized with all the screws helps! Thanks for watching!
Outstanding TH-cam tutorial. Following your detailed instructions, I was able to replace my LG frontloader's broken drain pipe motor in a few hours at a cost of $43.68, including the purchase of a spring expansion tool. I can't thank you enough.
AWESOME! Took this on with my wife tracking the screws. Your video was precise and concise. Worked out perfectly! I am mildly mechanical at best, but you made this a very accomplishable project. Took about an hour. Thank you!
Nice! You saved time and money by doing this yourself! Nice teamwork on your end! Nice accomplishment! Thanks for watching!
Thank you, thank you!! We had a service man come out, but he didn't have the replacement pump and told us to order it on Amazon and he'd come back to install it. I must pay him for coming out to assess the machine and to thank him for providing the part number required, but since I had to wait for the part I went on TH-cam to assess the installation process and found your video along with several others. I must commend you on the detailed instructions and outstanding video your put up. I decided to attempt the installation, purchased the spring extender you recommended, and replaced the pump myself in a couple of hours with my wife managing the screws. I wish others would follow your example on how to create a useful video with step by step instructions that almost made the installation process look easy. Thanks for taking your time to make the video and share your knowledge.
You’re welcome! Thanks for sharing your story! So even the repairman orders his parts from Amazon! You still saved a lot of money even though you had to pay for the diagnostic appointment. Nice work by the two of you! Thanks for watching!
I’m a girly and I did it all by myself ! Great video! 🙏🏻 plus I ove the fact that you made it so easy for us to press the link and buy the part with no struggle. This is awesome! Thanks 🤑
Excellent! I’m really glad you were able to do the repair yourself! It’s not too difficult to do and you save a ton of money by not having to call a repairman. It’s a good feeling of accomplishment! Nice work!
Thank you for your very thorough video. I was able to watch it, order the parts and tool and have it on hand for my husband to fix in less than an hour. Your video saved the day!
Thank you so much! Sitting here listening to my washer drain so smoothly during a wash cycle. This is a flawless video. Anyone can do it after watching your instruction.
Fantastic video, super detailed and I fixed my washer, saving big bucks compared to paying a repair service. I appreciate your recommendation on the spring expansion tool. It was a little tricky even with that tool, but I was able to get the retaining ring on properly on the third try. Without the tool, it likely would have been hours of frustration - Thank you so much!
You’re welcome! Really glad my washer repair video was helpful! That tool is a lifesaver! There was no way I was going to be able to get that spring back on without it. Maybe it’s a one use tool but if my washer pump goes out again I’ll have it ready! Thanks for watching!
Thank you, thank you! You saved us hundreds of dollars by giving us a way to do this ourselves. Your step-by-step instructions were very clear, and we followed them exactly, also buying the spring expansion tool. It all worked like a charm! I'd buy you a beer if you lived nearby. :-)
You’re welcome! Yeah the pump replacement isn’t too difficult to do but it can seem like an intimidating task. I’m glad you got the spring expansion tool and got the repair done! Thanks for watching!
I wish I could send you a picture of the wrench and zip ties I used as an “ expansion tool”. I zip tied one end of the wrench to the wire and then zipped tied the other side and then inserted the wire and then cut the zip ties and it worked like a charm. Thank you again for your video and guidance.
I'm with Joe on this! I just replaced mine today 08/12/21 and I watched your video first ordered parts and spring tool next....2 day shipping....and just 35min I was done from first screw out to last screw in. I owe you a dinner and a beer!
@@sassymexy5655 I could use that picture right about now .. ugh 😩
One of my screws to take the front panel off won’t come out:( tips?
Thank you, thank you, thank you. Not only did you save me a bundle in repair/replacement costs (husband wanted to replace), but you’ve restored my faith in TH-cam instructional videos. Concise and to the point, no long expositions or annoying music. Truly helpful material, and the experience was a confidence booster to boot. Subscribed!
You’re welcome! I’m really glad my washer repair video was helpful! In my videos there’s no need to add unrelated content. I like to make my videos as short and concise as possible. But this one is longer because there are a lot of steps involved. Also thanks for subscribing! I really appreciate it!
Glad I found your video! I just ordered the parts (thanks for the quick links!)
The video was step-by-step, well done! Thank you!
You’re welcome! I’m really glad my pump replacement tutorial was helpful! Thanks for watching!
Thank you sir! Much appreciated. No LG repair guys around here for 80 miles. Can not imagine how much this would have been. Almost entertained buying a brand new washer. Your video prevented that. Great angles, editing, everything really. Thank you!
You’re welcome! Yeah it would probably several hundred dollars to have a repairman replace the pump! Plus the markup on the parts would drive the overall cost even higher! So glad you were able to make the repair yourself and save money! Thanks for watching!
Thank you so much for your detailed video. I purchased the spring extention tool and a pump. Your video gave me confidence to try changing out the pump and I was glad my LG ventless washer dryer combo had almost identical steps. I was able to also use the spring extention tool to help remove the spring instead of using a screwdriver to wedge it out. A tip that I was given years back from the guy that installed my Machine on how to easily slide and move the machine was to spray something like windex or soapy liquid on the floor under the machine and that helps glide it and it really works. Once again thank you and I am so happy to have a pump that is working again.
Thanks for the tip on how to move the washer! And the spring expansion tool can definitely be used to remove the spring. I just didn’t have it when I started. But as you saw I had to order one so I could finish the job. Thanks for watching!
This is a great help video. I was able replace my pump myself as a result of watching this video. My machine was a little different but all the steps fit my model as well. Thanks for this one.
Seriously the most helpful repair video I've ever watched. Took me less than an hour.
If you don't want to or just plain didn't by the spring ring tool, an alternative is two sets of hands and a bike tire lever. Have one person hold the ring really tightly at the furthest locations you can get it to by hand and the other person start at one and slowly run the tire lever along the ring. Worked for me after a half dozen tries.
Really glad my washer pump replacement tutorial helped! And thanks for sharing how you reinstalled the retaining ring without the spring expansion tool! A few viewers have also made workarounds like you! Glad it worked!
Thank you so much for this video! Your step by step directions gave me a clear understanding of each step and what I could expect. I used a sticky note for each set of screws I removed. I labeled each sticky note and taped the screws to each. Thank you again!
Well done. My wife had gotten a quote of $400 just to change out the door gasket. We put up with the moldy door until the drain pump went out.
Thanks to you, I replaced the pump and the gasket today.
Excellent video.
My partner and I had never attempted these types of repairs.Your video was easy to follow, detailed,and extremely helpful to us.thank you
Though it took me longer than it took you, it worked!! My Unit had a metal bracket / brace that had to be fully detached from washer to replace the broken part. It didn’t have a quick clip like yours did. Added an hour of frustration, but I got it! Thank you
You’re welcome! I’m really glad you got around a snag that added more time to the repair! But also glad you got your washer fixed on your own without having to call a repairman! Thanks for watching!
I have to order mine do you what’s the part # of the water pump
Fantastic video! All details were spot on, especially the tool for expanding the spring. Thanks so much for making this DIY repair so easy!!!
You’re welcome! Glad my washer repair video was helpful! And yeah I wanted viewers to know how important it is to have that spring expansion tool. I tried without it and there was no way the spring was going back on. Fortunately it’s not an expensive tool even if it is just for one use. Thanks for watching!
Just want to say thank you for this post. It saved me big time and $$$! The job went exactly as you described & demonstrated. I bought the spring expansion tool for $12 can, and it worked perfectly. Thank you so much for taking the time to do such a complete demo of this repair. I literally was going to buy a new washer because I always have trouble with these front loaders. $58 can for the pump for an LG part. I used your links. This job can be done by anyone who watches this video!!! Great work man!
A wonderful instructional video. One of the best I have used. One point to highlight is to ensure that all water pipes are fitted tightly and for the main water pipe access maybe use a screw-down hose clamp as the one that comes with the LG is very difficult to fit due to the confined space.
Thank you. I followed the video as i was doing it from the beginning to the end. I’m happy I was able to repair it myself but I’m disappointed that this is an issue that is supposedly normal. I wouldn’t have expected any repairs whatsoever before at least 10 years. This happened after four years. Thanks again for the detailed instructions and clear video angles for each step.
Thanks a million! Just replaced my drain pump last night while following your video! That spring compression tool is a life saver, as is your vid!
Great video. Thank you! I found a couple small differences in my washer model but your directions were so clear it didn't matter.
You’re welcome! I’m really glad that you replaced the pump even though your washer was slightly different! Nice work! Thanks for watching!
Thank you so much! This is one of the best tutorials I've seen! Notes I learned from taking mine apart: 1. the door switch plug is easy to get to once you undo the screws and lean it down toward you, then you can get a hand from the side and the top. 2. For the spring I just used some needle nose and stretched the spring really far, then just rolled the wire over the edge, it was super easy and doable. 3. Plug the wires in while the motor is out and you can see it clearly, I first installed then plugged and didn't get the contacts to connect and bent a lead which caused some unnecessary work. Again, great tutorial, thank you for giving me the confidence to DIY!
You’re welcome! And thanks for the additional tips for this repair! I’m sure others will find your suggestions helpful! So glad you got your washer pump replaced yourself! Thanks for watching!
Great tutorial, worked like a charm! For the spring ring, I ended up using a pair of 8 in diagnal cutters. 😊 Took me a few tries but it worked! Thank you!
I had no problem tearing it down and replacing the pump. I bought the spring tool ahead of time and so glad I did. Excellent video.
So glad you were able to repair your washer using my tutorial! The spring tool really is necessary for that last step! Thanks for watching!
This video was brilliant. I managed to get the entire job completed by following the steps illustrated here. Upon re-assembly I didn't have the spring spreader tool. I determined that if the left side spring is in place over the gasket it will stay in place. You can then stretch the right side of the spring with a screwdriver, then guide the wire into place by hand on the right side without any issue. Just make sure that the retaining wire is inserted as best as possible all the way around the gasket. Then only about the last 1/3 of the wire to the right of the spring needs tucking in. This video is very clear and self explanatory. I saved quite a few bucks in repair cost to spend on myself following this guide. 😁
Very good instruction. This was exactly the way I took mine apart and got to the drain pump. Thanks for taking the time to record and post!
I recently had the same problem on my washer. Very well done video. Ordered the pump from Amazon, the OEM one not the cheaper one worked like a charm. Thank you very much, sir that was awesome.
Just used this video to replace our drain pump and it was great. Could not have done it without this video. Our model did have a couple of differences like it was important to put back the door lock before bolting the front door to the washer but other than that we were good. Thank you for such an excellent video.
You’re welcome! Glad my washer repair video helped you get your washer running again! Definitely helps to watch the process before starting your own repair job! Nice work! Thanks for watching!
Thank you so much for this video! For the past week or so during the drain cycle, my washer was making a terrible grinding noise. It would finish the cycle, but this morning with a load full of laundry, I got the dreaded OE message. I had already known about this video before it actually stopped working (I'm anal that way) and I was fortunate that a local parts supply place had the pump in stock along with the spring tool.
I'm 65 years old, and in the past seven years it seems as though my washer had glued itself to the floor. Moving the washer into a position to work on it was the most difficult thing for me.
Your tutorial was perfect, and it only took me about 2 hours to do the repair once I started working. 10 stars, and 20 thumbs up for this help!
I'm now kicking back enjoying a celebratory Scotch👍🍻👍
Thank you, thank you, thank you!!
You’re welcome! I’m glad you were already familiar with my video! On my washer I got very little notice before I got the OE error code. The fix is kind of simple yet quite involved. It’s nice that you were able to find a replacement pump locally including the tool! Being able to fix it yourself is definitely a cause for celebration! Thanks for watching!
I watched so many videos and finally found this one half way through the repair! Thank you so much!
Thank you. I just ordered the drain pump from amazon and I will watch again before beginning the repair of my LG Washer. Thank you. You are so easy to listen to.
You’re welcome! Glad you were able to order the replacement pump! Hopefully you got the spring expansion tool too! It makes that last step a breeze. Others have reattached the spring using other methods but I was not able to without the tool. The repair is fairly easy so I’m confident you can do it! Thanks for watching!
Thank you so much. You are a life saver. We came home from a long trip and no clean clothes to a broken drain pump. Repair company was at least 3 day wait... I got it done thanks to you in 24 hours (and amazon).
Nice! Thanks for sharing your experience! You got it done faster and way cheaper than a professional repairman! Great work and thanks for watching!
This was so perfect! My father in law and I followed this video step by step (after watching it through once). Worked perfect! Thanks for saving us a ton of money!!
Excellent! I’m glad he watched it through once before doing the repair. I think it really helps to be familiar with the process before starting! Glad your father in law got the repair done saving you guys money! Thanks for watching!
Thanks for such a detailed video. This was extremely helpful. I had the exact same problem and my repair went exactly like yours did.
Thank you ! I have the same model, same problem, and your video instructions, I'd have wasted a lot of time trying to figure out how to access that pump. You're a life saver.
One note on the spring extension tool, I did not have one, but found out that it's not difficult if you have two people : One holds the spring open with two screwdrivers, the other puts the ring in the grove. Works like a charm.
Thanks! I had booked a repair guy - $120 for the visit and diagnosis plus more for the parts and labor.
It took my an hour to disassemble and half hour to reassemble. I’m still waiting for the spring tool to finish that last piece.
I only had two hoses and two wires instead of four connected to the pump.
Very detailed and thorough. Thanks!
I was going to take the gasket off completely and clean it but was afraid I wouldn’t get it back on the right way.
This is the best video on this repair. Easy to follow, and to the point. I will do my repair this weekend. Thank you for posting this.
Thank you so much for this very helpful video. My husband and I were able to repair our washer and it works great. We saved hundreds of $$ by watching this. We live in an area where there doesn’t seem to be any repairmen. For $60 we were able to make our washer work like it did before.
Excellent! Definitely saves a lot of money doing this repair yourself! It looks a bit intimidating but not too difficult to do. Thanks for watching!
Thank you so much for the great video, it made doing this so much easier. I watched it twice before starting and replayed each step while I was working. Luckily my wife was a great assistant and a second set of hands for some parts (especially placing the washer spring back). I appreciate the in-depth tips, explanations and the great production. Thank you!!
I am not mechanically inclined but this video was so well done and so easy to follow, I was able to fix my washer. This saved me so much headache and a ton of money so huge thanks to the creator!
You’re welcome! So glad you were able to fix your washer yourself! It definitely looks intimidating but going step by step it is manageable! Nice work! Thanks for watching!
Than you so much for this video! I ordered pump and tool and was able to repair my washer easily! Mine didnt have the bolts requiring the socket wrenches but had a tab ( I finaly saw with help of a mirror and light) witha channel it slid back and out! Thanks to this video I had the confidence to do it myself!
You’re welcome! I’m glad you got the parts and made the repair yourself! I’m happy my tutorial helped! Excellent work! Thanks for watching!
We just wanted to give you a huge SHOUT OUT for just helping us save hundreds of dollars, I am so glad I came across your amazingly detailed video of this repair. We did everything you said, right down to the spring expander tool (so important!) and 2-3 hours later, we have a working washer again!! Thank you so much for taking the time to post this repair video… and helping people who had no idea that we would be capable of fixing something like this, you were with us every step of the way!! … After Joe Roberts buys you a beer, we’ll be buying you another round!! THANK YOU again so very, very much!! 😊🙏🏼
You’re welcome! Makes me feel like my time was well spent making this video when I hear stories like yours. I’m really glad you got the repair done and saved money doing it yourself! Thanks for watching!
I agree with everyone else - this is an excellent video, a perfect model for repair videos. In addition, the inclusion of the text of your instructions is the glitter on the icing on the cake! Thanks.
You’re welcome! I try to make my videos as detailed as possible partly so that if I ever had to refer back to it I would know step by step how I did the repair. So glad your got your washer fixed! Thanks for watching!
I just replaced the drain pump with the help of your video clip. I also ordered the pliers which make the job easier. I expect that the pump will need to replace again ( the old one last ten years). Thank you
You’re welcome! I’m really glad you were able to replace your drain pump using my video. Those pliers for the spring really comes in handy. And even though it was for one use it’s still worth it considering the cost if a repairman were to do the job. Thanks for watching!
Now this is how to make a great how to video. Excellent camera and lighting. Very detailed explanation of work being performed. You made my life a lot easier. Thankyou for your time and trouble.
You’re welcome! Really glad you enjoyed my video tutorial! I like to put as much detail as I can in it because partly it’s a video for me in the future if I ever have to do this repair again! Thanks for watching!
I watched your video several times and decided I could not afford to throw out my LG washing machine. So I ordered the part and the tool to install the wire. You are awesome. I completed the pump replacement and my machine is working perfectly. Thanks a million. PEOPLE PLEASE CHECK YOU POCKETS before doing a wash... All the best. David.
You’re welcome! I’m really glad you were able to replace the pump yourself! It’s not difficult but there are a lot of parts to remove first. Glad you saved money by not having to call a repairman! Nice work!
I watched several videos before this one. I really had doubts about trying to do it myself. After watching this one I didn't. It was very well done. I watched it beginning to end, went and bought the part and spring tool, and then watched it in segments as I did the job. It was an excellent tutorial and I want to say thanks for saving me some $$$$. The only place I disagree with the OP is that for me getting the main drain hose back on was the hardest part. But, it might have been the angles along with the pliers I had to use. All in all 10/10 from me. Thanks!
You’re welcome! I’m glad my detailed video gave you the confidence to take on this repair! I didn’t have any problems with my tubing but I can see how it can be difficult with the small space under the washer. Nice work doing it yourself and saving money! Thanks for watching!
Wow! Even explains how to put it back together! Best video and overall quality/detail on this subject--what a relief to have found this. In fact, invaluable instruction and tips whenever taking anything apart! Thank you.
You’re welcome! I’m glad my washer pump replacement tutorial helped! I tried to make this as detailed as possible just in case I had to do this repair again in the future! Thanks for watching!
Great video. Thanks for the info. I saved a few bucks and made my own spring expansion tool with two small head screw drivers and two zip ties. I crossed the screw driver shafts, put a zip tie going in each direction and it worked like a charm.
Excellent work! I think another viewer also made his own spring expansion tool! You guys are very creative!
Excellent job describing the process! Regarding the ring installation, I was able to get the ring back on using two bike tire levers. It’s a little finicky but possible. The expansion tool is probably an easier method. But in a pinch, the tire levers will work. Just get the ring started on the top half. Place two tire levers in the 4 and 8 o’clock positions. Place pressure toward the machine on the levers and wiggle them down to the bottom and push the spring over the ring retaining lip.
Thanks for the video!
You’re welcome! Glad my washer pump replacement tutorial helped! Nice work getting the spring back on without the expansion tool! That’s a great workaround! Thanks for watching!
This video was perfect. I was able to take my washer apart, get the correct replacement pump and reassemble everything and it works like a champ! I even purchased the spring expansion tool and as the video stated, it was WELL worth the money because I tried it without the tool and it cost me about 20 minutes of frustration. Thank you!
You’re welcome! Yeah that spring expansion tool is a lifesaver in the last step! When I was shooting this tutorial I had replaced the pump but couldn’t get the spring back on. Had to wait 2 days for the tool to arrive from Amazon. Got the ring back on and finished shooting the video! Even buying the pump and tool costs much less than calling a repairman! Thanks for watching!
@@digitalcamproducer That's exactly what happened to me. I took the washer apart one day to get the pump out to get a feel for the job, order the pump, waited for it to arrive, replaced it and then was like "Crap, I can't get this damn spring on" and had to wait 2 more days for the tool. Lol. Anyway, you're right that it was a lot cheaper than replacing the washer or having a repairman come out plus I scored points with the wife :)
Awesome video. Got it working as described. I pulled the old pump apart and it was full of crud. Not sure if that was the problem but happy to have a new, functional pump in.
Thank you for showing every single step. I am not a handyman and was able to fix my machine. We just save $1,500 thanks to you!
You’re welcome! I’m glad you were able to save money doing the repair yourself! I wanted to make the video detailed in case I have to do this repair again in the future! Thanks for watching!
Great video. I changed my own pump a couple of weeks ago, before I watched this video. The only thing I would change is to to be sure to Shut off the water before proceeding.
This is the most detailed and easy to follow repair video I've ever seen for this problem... there are several floating around.
I was able to follow this and the machine is now working. My only recommendation is you mention all the required and optional tools at the very beginning of the video.
You saved me $500 and encouraged me to self repair other things around the house that I would have probably thrown and and purchased.
Thank you so much!!!!!!!!!!
You’re welcome! Glad my video was helpful! Yeah mentioning the tool in the beginning would be a good idea. Nice you saved a bunch of money doing this repair yourself!
Great useful video. I just cleaned the pump and put it back in.
I did get the toughest part done without the tool. I pulled the spring open with two small screwdrivers while my wife helped get it in the groove.
Excellent! Glad you got the spring back on without the expansion tool! That part really is the hardest step in this repair! Thanks for watching!
God bless this man! You saved me from dragging my washer to the curb and buying a new one! Great great great how to video! Thanks bud!
You’re welcome! Really glad my washer pump replacement tutorial helped! Really saves money when you can fix it yourself! Thanks for watching!
Awesome video and very well done! I had no issues following your step by step video in changing the drain pump and our washer is back to normal again. Thanks and keep up the good work👍🏽
You’re welcome! Very glad to hear that you were able to replace your washer pump using my tutorial! Definitely saves money doing it yourself! Thanks for watching!
Excellent instruction. Easy to follow and appreciate the details on tools used. Fixed my 15yr old LG washer. Keep posting !
So glad you were able to replace your washer pump yourself! Saves a lot of money by not having to call a repairman! Nice work! Thanks for watching!
Amazing video! Purchased the pump and spring tool and followed your instructions step by step. Bravo!
Excellent! So glad you were able to replace your pump with the help of my tutorial! Nice work! Thanks for watching!
Just Replaced Mine
TY for such a great video and explanation of the whole process.
Did it, replaced my pump and fixed my washer! Thanks for the video!
Thank you for this video. I was able to change the pump on my LG washer easily with this video and successfully.
Thank you very much. Your instructions are excellent. I taped the screws to paper and labeled them. The spring tool I purchased was 20$ and worked great.
You’re welcome! That tape idea to keep your screws organized is a great idea! I might have to use that in the future! Glad you were able to get washer working again!
Awesome instructions and saved me a bundled. The spring tool was a lifesaver. Great job and thank you!
You’re welcome! I’m glad my washer pump replacement tutorial was helpful! Yeah I had to tell everyone that the spring expansion tool is a necessary tool to help with this project. I know mostly it will be a one use tool but at least it’s not very expensive! Thanks for watching!
Very helpful! Extremely easy to follow along. My washer was a newer model, but this video still applies.. just a few less screws.
Thank you!
You’re lucky you have the newer model! I guess LG realized how time consuming it was to take the thing apart to get to the pump. It would’ve saved me so much time if I didn’t have to take all the panels off! But I’m really glad that you were able to repair the washer yourself! Thanks for watching!
@@digitalcamproducer Thanks again! Yes, definitely a little easier. They certainly simplified it a little.
Thank you for the well made video. It made the drain pump changing job so much easier for me.
Thank you so much for ur video! I fixed my washer following ur every step and I can’t say how much money I saved doing it myself. Again…thank u!
Wow thank you! I just did this repair on my LG that's almost identical to this video and your attention to detail made the job so much easier. I'd just add a word of caution to anyone that I think the 3 bolts that hold down the pump assembly go into plastic and only need to be hand tightened, could easily strip the plastic threads if using a ratchet to re-assemble. I could be wrong.
Pump replacement was successful. That expansion tool was indeed a lifesaver. I also used it to remove the ring, instead of prying it off with a screwdriver 😅. It was super helpful to have watched the video also for the prep and having all the right tools available as well as the tip to mark and organize the screws. Thanksssss!
You’re welcome! I would’ve used the expansion tool to remove the ring also but I started this repair before I knew I needed one. So this video took extra time to shoot because on the final step I had to wait for the expansion tool to arrive. So glad you were able to get your washer fixed! Thanks for watching!
Thanks for the level of detail, like the bits about the socket extension depths and sharp sheet metal! I feel like a lot of the How-To's I see always leave something out and it was really comprehensive. Used the affilliate link for the pliers. Thanks again!
Well done - there was no corny, unnecessary commentary that dominates DIY videos. I'm not handy, but was able to swap out the pump. On Amazon - bought the pump for $20, and the spring tool for $12. $32 repair and 90 minutes of my morning vs a new $700 washer, or $300 repair. The hardest part was getting the pump out of the plastic housing. The spring around the window was easy with the "spring tool."
Omg this video helped so much. Me & my sister fixed my washer...can't believe it. Thank you so much...single mom of 5.. I so needed this!
I’m so excited to hear stories like yours! Really glad you got your washer fixed and running again! Nice feeling being able to do it yourself without having to call a repairman! Great job! And thanks for watching!
Thank you for such a clear and concise video! So professionally done, and you warned us about having the right tool for the job to mitigate the stress and swearing that normally comes with tasks like this. You killed it!! Two Thumbs Up! I'd give you the Academy Award! LOL!!👍🏼👍🏼🏆
You’re welcome! This was the first and only time I’ve done this washer repair and wanted to make sure I capture all the steps so that I can refer back to it if i ever had to do this again. In the past I’ve had repair people out and they cost a lot of money for this type of work. Thanks for watching!
My friend thank you for this awesome video you posted my friend..My washing machine I bought in 2014 and the insurance had ran out and thanks to you My machine is up and running just like when I bought it….Thanks..
You’re welcome! I’m really glad you followed along with my video and fixed your washer! Excellent work! Thanks for watching!
This is my first time replacing the pump on my front load LG washer. I dread it but it his video will help. Thank you so much.
Great video. It made the job easy. I didn't do a great job of tracking my screws and things would have gone quicker if I had heeded your advice. Thank you.
Best how to video I’ve ever seen. Well done.
This is such a great step by step video, this is what we used to repair our washing machine on Thanksgiving day. Thank you!
You’re welcome! Wow! You did the repair on Thanksgiving! So glad you were able to follow along with my video. I know it seems a bit intimidating to disassemble part of your dishwasher but when it’s laid out step by step it’s not so bad! Nice work! Thanks for watching!
@@digitalcamproducer Thank you and I am wondering if anyone else has had the same error code show up AFTER we replaced the drain pump (in our front loading washer) it read tE which says it's a thermistor but since we have no heating element we think it could be the control panel. WE are learning so much and it started with your video! Thanks again.
Thank you so much for the video. Such easy steps. This video has helped us fix our washer machine 2 times, last time we fixed it was year ago. Thank you so much!!!!
Thank you for this video! Mine has been down for about 3 weeks now.. and the laundromat seriously sucks!! I watched a lot of videos before yours and this one was the best! Super helpful and fixed the problem without spending tons of $$$ on a repairman! Glad I bought the Spring Expansion Tool you recommended too. Your video was so easy to follow too. Took much longer than you did.. but in the end the washer works better than it ever did!
Really glad you were able to fix your washer yourself! Seems intimidating but it’s not too bad! Regarding repair time I would say it probably took me longer to do my repair because I was shooting video and trying to get the best angles. Plus I reshot quite a few of the steps multiple times for wide angle and close ups. But definitely the spring expansion tool is a life saver! Too bad I can’t just hand that tool out to everyone following my video! Thanks for watching!
Great video! For the “spring stretching” part at the end I used a scissor, put the two tips in each loop and pull apart. You’ll need someone to help you walk the ring in but it works! Thanks again!
You’re welcome! Glad you found an alternative solution to help with reinstalling the spring. Nice work repairing your washer! Thanks for watching!
Thank you very much for this. Huge help, especially the parts links. Ours just started throwing OE with very non-pump like noises.
You’re welcome! You should be able to replace the pump without too much trouble. Mine didn’t show any sign of potential problem. It just stopped working. Thanks for watching!
Thank you, your step by step explanation helped me to fix the issue with my LG washer. You are just Awesome..
You’re welcome! I’m really glad you got your washer working again! Nice job! Thanks for watching!
THANK YOU! I am not very handy and normally would just call someone to do the job but no one could come out for several days. The Spring Expansion tool was a life saver and made my final step of reassembly a breeze. I struggled with the bolts on the for literally a couple hours, getting them out and then back in. The bolts just didn't come out, eventually I had to pry out with a screwdriver because the rubber feet had got stuck or affixed in place. Then the base wouldn't tighten down when reinstalled. You mention in your video that it is supposed to have some "play" but I didn't catch that until after completion.
Nice work! Glad you were able to do this diy repair yourself and save money! It does seem intimidating to take all those parts off the washer but it’s not too bad. Thanks for watching!
My washer stop draining and was making noises so I found this video and was able to repair it. I had my husband help me put the ring back on so I didn’t need the spring tool. If you’re by yourself I would get the spring tool. I had my lg washer since 2006 and this was the first time I had any problems with it, the inside was a little different but I was still able to follow along. The draining tube had sand stuck in it so I was able to clean it out as well. Now it works with no issues 🤞🏼you saved me $300 dollars! Thank you!!!!