Thanks for taking the time to make a video, I wish I had that skill since the videos are helpful. A constructive comment.....clean the tiny holes out on the side of the jets also. As another commenter mentioned, I use a thin wire from a wire brush for this task. If you don't clean those holes, the bike may still run like crap after reassembly. Randy
Thanks for the video! I can't figure out how to remove the throttle cables so I just cleaned it while still on the bike. Took the carb out of the boots and rotated the bottom toward me.
Thanks. Those pilot jets are so small they need to be cleaned every ride or two, or if put away without running the carb dry. I can leave the carb on the bike, just take off the bowl, and clean both jets in about 5-10 min. They say not to do it, but I always use a strand from a wire brush to clean, many years with no problems.
they make these little brushes that you can brush out the inside of your jets with id say thats your problem if not, then the carburetor probably need tuned
Mine was sticking also. In my case it had to do with a burr in the alignment slide groove. Drove me nuts for awhile trying to get it right. Finally located the burr, filed it down and all was good. Those slides are finicky
![THE TOYS x NONT TANONT - ดอกไม้ที่รอฝน (spring) [Official MV]](http://i.ytimg.com/vi/pPa1d5cC8M4/mqdefault.jpg)
Thanks for taking the time to make a video, I wish I had that skill since the videos are helpful. A constructive comment.....clean the tiny holes out on the side of the jets also. As another commenter mentioned, I use a thin wire from a wire brush for this task. If you don't clean those holes, the bike may still run like crap after reassembly. Randy
thanks randy
Great video, thanks. Was able to clean carb after watching. Great step by step and tool identification
Thanks for the video- worked a treat for my mrs bike that stopped running!
Thanks for the video! I can't figure out how to remove the throttle cables so I just cleaned it while still on the bike. Took the carb out of the boots and rotated the bottom toward me.
Great help full video mate👍💪
Thanks for taking the time to do this vid.
+M Briggs no problem thanks for viewing
Thanks. Those pilot jets are so small they need to be cleaned every ride or two, or if put away without running the carb dry. I can leave the carb on the bike, just take off the bowl, and clean both jets in about 5-10 min. They say not to do it, but I always use a strand from a wire brush to clean, many years with no problems.
+DSC800 thanks for the advice man were still kinda learning, if you wouldnt mind helping us out alittle? thanks much appreciated
Nice job!! Thanks!!!
My bike doesn’t start with choke off even when is already warm choke has to be on otherwise it won’t start.. can you help with that
@Angus Pinkerton thanks a lot, hope you subscribe more videos like this one on the way!
Hey man I'm struggling with getting the little screw back onto that top push pull thing were the link is
the throttle cables??
What bikes do you guys have? What is your fav. bike? Would love some comments back!!
230, sorry for the late reply was afk
What about the one you said not to mess with if you didn't have to? My bike is still not 100% and I wonder if it's kinda clogged also.
they make these little brushes that you can brush out the inside of your jets with id say thats your problem if not, then the carburetor probably need tuned
How do you go about tuning it?
im not completely sure, ive never had to do it myself but it consists of new jets and finding the right air/ fuel ratio
do you Kno how to get the slide out? mine is sticking
J. D. I have the same question
Mine was sticking also. In my case it had to do with a burr in the alignment slide groove. Drove me nuts for awhile trying to get it right. Finally located the burr, filed it down and all was good. Those slides are finicky