ฝัง
- เผยแพร่เมื่อ 19 มิ.ย. 2024
- My MT09 has rattled its last CCT rattle. It's time to swap to a manual tensioner and kill the rattle... well one of them.
0:00 Intro
0:20 Disclaimer
0:49 Removing the Stock Tensioner
3:40 Installing the MCCT
5:32 Setting the Tension
6:14 Better Safe Than Sorry
6:59 Using a Mechanic's Stethoscope
7:53 Outro
#mt09 #yamaha #motorcycle #motorcyclemaintenance - บันเทิง
Not my bike but for those with this particular model, they just got an excellent tutorial to solve a chronic issue. Well done. Cheers 🍻 Eddie
I ride a FZ1 and I'm thinking about getting a 2021 or 22 MT09, so the TH-cam algorithm brought me here I guess 😊You did a very good explanation of what can be a tricky installation, I don't think I need it any time soon but I still enjoyed it a lot. Thanks!
Great video. Thanks for posting!
Great job. Thanks for sharing
awesome content. thank you for sharing. Have a Good Day!❤👍
Jeff. this is above my pay grade but you sure did a great job showing what to look for. Great job. Eric
Thanks Eric!
Just trying to spread some knowledge 😉
Awesome work man. I don’t dabble anywhere the sun don’t shine (internals) lol. But awesome step by step nonetheless
Thank ya sir 😆
روعه 🤝🧚♀️👍
Have you had the clutch basket rubbers fail yet? I had to drill out my basket rivets to get the steel plate off the drive gear side to get to the rubbers and replace them. Tapped and put helix coils in M6 by 1.00 bolts in. Hinson makes the rubbers. Their CU216 Hinson cushion kit. Did the clutch as same time. Only issue with that was the lever had a ton of slack after I put the Recluse Torq drive clutch in. Adjusted the cable completely the opposite side, with the lever adjuster half way out before I got it to syn up. PIA
I plan on checking out the clutch basket and rubbers before riding season this year. By the end of season last year it did have a bit of clutch noise, so I am thinking that a basket or bushing replacement will be in order.
Thanks for reminding me about the Hinson options available and letting me know about the clutch cable adjustment.
How does your clutch feel and sound after the install?
Motor yang sangat gagah dan istimewa
Terima kasih.👍
Hello i would like to ask you why is that setup for? I mean if you keep that noise is gone to be something bad to the engine or is good to check and fix it?
This assembly is to replace the automatic timing chain tensioner, which can sometimes fail to tension or hold tension on the timing chain.
If the chain gets an excessive amount of slack, it can cause the chain to jump teeth on the sprockets and cause catastrophic engine failure. This stock adjuster was nowhere close to that point of failure, but was replaced as a preventative measure against failure while on the road.
Can you do this for a 1984 CB700SC now?! 😜😜 I think my auto cam tensioner is worn out 🥲
Haha pretty likely that it's worn out. If I remember the 700 Nighthawk right it used in internal tensioning setup that was pretty awkward. I don't know of a way to manually tension those, but there may be something out there.
Can you turn the engine over before and after installing the new cct? I saw another video where you can look at the notches while turning the engine over to see if they align before installing the cct.
I did not check the timing marks before or after the install. There wasn't enough slack for the timing to have jumped, and the bike still ran fine. If the timing has jumped for some reason then the bike would run pretty horrible if it didn't bend valves or worse.
As long as you keep tension on the chain, like I did by sticking the socket extension behind the chain guide, it should stay put. If for some reason it lost tension and the chain jumped you would hear it as it happened. I would definitely check the marks before installing the MCCT if you even think it jumped time.
Hope that helps.
Or you could Just adjust the original one with a Quarter turn clockwise.
That is a possible temporary fix. The ability of the original to adjust on its own and hold that tension is the source of the problem. They tried it fix it in later years by routing oil pressure into the tensioner, but they still fail to hold. You could force the adjustment, but no guarantee it will hold.
The MCCT just takes that chance out of the equation.
Compatibile con MT 09 anno 2021?
Can I used this to 2021 mt09?
I believe the 2021+ engine uses a different style of tensioner.
The installation would be similar but will probably require a different tensioner for that engine. Check with the tensioner manufacturer before ordering it just to be sure.
Where did ya buy that?
I picked this one up from Amazon for around $50 US
Cuanta tension debe llevar la cadena de distribución??
Able to move slightly by hand. Maybe 1mm at most.
Capaz de moverse ligeramente con la mano. 1 milímetro como máximo.
How much,where can i buy it.tq
They are available from a ton of places. This one came from Amazon and cost around 40 dollars at the time.