How to adjust your clutch cable on a Yamaha R3

แชร์
ฝัง
  • เผยแพร่เมื่อ 23 ธ.ค. 2024

ความคิดเห็น • 30

  • @iridewithneil1404
    @iridewithneil1404 8 ปีที่แล้ว

    omg the day you uploaded i was looking for a tutorial

  • @ACProductions77
    @ACProductions77  8 ปีที่แล้ว +1

    Glad to hear that it helped you out, I always try my best to get the videos out asap few more videos will be posted soon.

  • @matthewli1080
    @matthewli1080 4 ปีที่แล้ว +2

    Extremely helpful, thanks

  • @ayosirsnow
    @ayosirsnow 5 ปีที่แล้ว

    I just want my lever to be closer to the handle bar to get rid of my wrist pain. Would this adjustment help me with that?

  • @zanecrofts7085
    @zanecrofts7085 ปีที่แล้ว

    Which way do you turn it to tighten it at clutch end

    • @ACProductions77
      @ACProductions77  ปีที่แล้ว

      to tighten its counter clockwise by the engine or by the lever

  • @DougTheMan376
    @DougTheMan376 3 ปีที่แล้ว

    Hi i’m having an issue where if i don’t have it extra right it’s hard to put in gear and it drags?

    • @ACProductions77
      @ACProductions77  3 ปีที่แล้ว +1

      you may need to replace your cable or have your clutch pack checked out by a shop

    • @DougTheMan376
      @DougTheMan376 3 ปีที่แล้ว +1

      @@ACProductions77 Thanks will do and I’ll update just in case anyone has a similar issue

  • @derrickc3693
    @derrickc3693 6 ปีที่แล้ว

    Hi, do you have free play with these levers? Have the same levers but there is no free play . Absolutely tight

    • @ACProductions77
      @ACProductions77  6 ปีที่แล้ว

      i have a little bit of free play which is ok, as long as you don't have any restriction on the levers you should be good.

  • @jakefromstatefarm4984
    @jakefromstatefarm4984 7 ปีที่แล้ว

    If I want to adjust the clutch to engage closer to the handle bar do the nuts need to go up or down?

    • @ACProductions77
      @ACProductions77  7 ปีที่แล้ว

      it will have to go up but be careful that you dont go to far that you dont have the screw at the edge, cuz that will put alot of strain in the screw plus it will have barely enough bite on the threads that it could bend the screw

  • @siksniper1996
    @siksniper1996 7 ปีที่แล้ว

    If i have adjustable levers and I want the clutch engagement point to be closer to the handles bars do I need to adjust the cable or am I able to just use the lever adjustments?

    • @ACProductions77
      @ACProductions77  7 ปีที่แล้ว

      if you want the engagement to be closer then you will have to adjust the cable. the adjustments on the lever is just for how close or far you want the lever has nothing to do with the engagement point. but i do suggest 1st adjust the lever where you feel most comfortable before adjusting the clutch cable.

  • @angelarzate6563
    @angelarzate6563 8 ปีที่แล้ว +1

    i just put on some shortys on my r3 and my clutch lever wont retract all the way back what do i need to do ??

    • @ACProductions77
      @ACProductions77  8 ปีที่แล้ว

      you need to adjust the tension on the cable

    • @ACProductions77
      @ACProductions77  8 ปีที่แล้ว

      check out my " how to install clutch cable adjuster" video

  • @mikefawc22
    @mikefawc22 5 ปีที่แล้ว

    When you change a clutch lever do you want it in gear or no?

    • @ACProductions77
      @ACProductions77  5 ปีที่แล้ว

      it doesnt matter if you have it in gear or not.

  • @jakefromstatefarm4984
    @jakefromstatefarm4984 7 ปีที่แล้ว

    When I have my bike on a rear stand, put in 1st gear the wheel automatically starts spinning by itself even with the clutch held in all the way (to the handlebar). What do I need to do?

    • @ACProductions77
      @ACProductions77  7 ปีที่แล้ว +1

      Jake From State Farm nothing that's normal because the engine is spinning that will cause the wheel to spin if u have up on the stands. On the other hand if u Don't have your bike on the stands and your sitting on it and the bike starts to move once u put it into gear and have the clutch held in all the way then u need to adjust the clutch cable by the adjustment nut by the lever.

    • @jakefromstatefarm4984
      @jakefromstatefarm4984 7 ปีที่แล้ว

      AC Productions ty for the advice and quick response

  • @sn0wtec
    @sn0wtec 8 ปีที่แล้ว

    how do i know that the clutch does not fully close?

    • @alfonsocastillon8714
      @alfonsocastillon8714 8 ปีที่แล้ว

      you will know when you feel your bike start to move with out you giving it any throttle. or if you have your bike on a rear stand you will see the rear tire start to spin

  • @susanlang1630
    @susanlang1630 ปีที่แล้ว

    Just use a nickel to adjust at the purch

    • @ACProductions77
      @ACProductions77  ปีที่แล้ว

      you mean to stick a coin in the slot to move it?

    • @susanlang1630
      @susanlang1630 ปีที่แล้ว

      @@ACProductions77 between the clutch handle, and it's purch, use a nickel to get the 2mm measurement. 2 mm measurement would be about 10mm from the clutch handle to handlebar grip.

    • @ACProductions77
      @ACProductions77  ปีที่แล้ว

      @@susanlang1630 ah ok thank you for sharing that good tip

    • @susanlang1630
      @susanlang1630 ปีที่แล้ว

      @@ACProductions77 ur welcome. Thank u for the video