Not All Warm Meat Is Tasty!
ฝัง
- เผยแพร่เมื่อ 14 ต.ค. 2024
- Walk in cooler was at 50 degrees and other issues.
- Purchase your tools at www.trutechtoo... and use the offer code SURVIVAL to save 8% on your total purchase (exclusions may apply) -
D-TEK Stratus Detector trutechtools.c... 13 nt-Leak-Detector-and-Portable-Monitor?aff=
D-Tek 3 Leak Detector trutechtools.c...
Inficon Recovery Machine trutechtools.c...
Inficon Comb Analyzer trutechtools.c...
Testo Comb Analyzer trutechtools.c...
Testo 557 Manifold trutechtools.c...
- TOOLS I USE -
FULL TOOL LIST ON THIS PAGE - kit.co/hvacrsu...
💥 Amazon Store: www.amazon.com...
SHORT TOOL LIST BELOW
Fenix PD25R (EDC Light) - amzn.to/431c7C1
Fenix PD35 V3.0 (My Daily Driver) - amzn.to/4c0w7cf
Polyamide Clip-On Kydex Flashlight Holster for Fenix PD35 - amzn.to/49XjQ6k
MTR Micro 6000 Rosebud Heating Tip - amzn.to/3Qpmk5s
MTT Micro 6000 Flexible Twin Tip - amzn.to/40sTu92
MTF-5 Cap'n Hook Tip - amzn.to/3SnGr6E
Uniweld 71 Welding Handle Needed For Above Tips - amzn.to/3QiNJpC
TOPDON TC003 Thermal Imaging Camera, 256x192 IR High Res amzn.to/3sWLTTn
RIDGID 31305 Model E-110 9.5" Offset Hex Jaw Pipe Wrench - amzn.to/3Bar08y
Klein Tools Ratcheting Box Wrench 1/4 x 5/16 amzn.to/3GOpBrG
KNIPEX Tools - 10" Pliers Wrench amzn.to/3U7RRJf
KNIPEX Tools - 10" Cobra Water Pump Pliers amzn.to/3Wje8Wn
Knipex Tools - Mini Pliers in Belt Pouch amzn.to/3WguyyH
KNIPEX Tools - 4" Cobra XS Water Pump Pliers amzn.to/3UaQiKA
Bahco -6" Wide Mouth Adjustable Wrench amzn.to/3sHIsMV
Bahco - 8" Big-Mouth Adjustable Wrench with Rubber Handle - amzn.to/3SPhDB7
Knipex - 9.5-Inch Ultra-High Leverage Lineman's Pliers amzn.to/3DTLJ2h
Klein Tools Diagonal Cutting Pliers with Angled Head - amzn.to/3zuBVJb
Klein Tools Stripper, Crimper Tool - amzn.to/3gQQ6Su
Klein Tools Wire Cutter and Wire Stripper - amzn.to/3Fs627W
Klein Tools Kurve Wire Cutters, Heavy Duty Wire Stripping Tool - amzn.to/3FseIuW
Klein Tools Heavy Duty Automatic Wire Stripper - amzn.to/3SQdZab
Klein Tools Crimping and Cutting Tool - amzn.to/3TPIgXU
Klein Tools Screwdriver Adjustable 4 to 8-Inch amzn.to/3Nl6KWz
IDEAL INDUSTRIES Digital Circuit Breaker Finder - amzn.to/3DoBFwm
Fluke 376FC AC/DC Clamp Meter with iFlex - amzn.to/3UaNyx2
Fluke 62 Max Industrial Infrared Thermometer - amzn.to/3SNdwWg
Fluke 902 FC HVAC True-RMS Clamp Meter - amzn.to/3Ws7OfB
Fluke 87V MAX - amzn.to/3U6Rlv9
Fluke Networks Pro3000 Tone Generator - amzn.to/3WedklG
Fluke - FLUKE-52 Dual Input Digital Thermometer amzn.to/3zwFdf1
Ideal Safe-T-Grip Fuse Puller - amzn.to/3zsw2w4
Klein Tools Canvas Zipper Bag - amzn.to/3WgnJxq
Uni-Paint PX-20 Oil-Based Paint Marker - amzn.to/3sE3R9T
5 Gallon Bucket Topper and Organizer - amzn.to/3sGi2Ll
Stabila Magnetic Pocket Level PRO with Holster - amzn.to/3FtYLo0
Clip & Carry Kydex Multitool Sheath for LEATHERMAN SURGE - amzn.to/3TPJfHA
Kydex Multitool Sheath for LEATHERMAN WAVE & WAVE + PLUS - amzn.to/3sJlhlg
Cooper Atkins Thermistor Thermometer - amzn.to/3DLeHkC
GEARWRENCH Internal/External Ratcheting Puller 7 Ton 2 or 3 Jaw - amzn.to/3FxTU5l
- CONTACT INFO -
hvacrsurvival@gmail.com
- FOLLOW ME -
Instagram - / hvacrsurvival
Facebook - / hvacrsurvival
Warning Notice Disclaimer - Video content listed on the channel HVAC*R Survival is for entertainment purposes only! **Do not attempt anything said or seen on my videos, The tasks that are shown are dangerous and deadly without proper training.
**This page contains affiliate links, which means that if you click on the link and make a purchase, I’ll receive a small commission. HVAC/R Survival is a participant in the Trutechtools, Amazon Services Associates Program.
#hvacrsurvival #hvaclife #hvacservice #hvacr #refrigeration #troubleshooting - บันเทิง
I think I was an equal opportunity pisser offer on this video. I hopefully didn’t leave anybody out. 😂
just to be sure, you're not found of coldpack, and their engineering, CORRECT ?
I’m just here to hear Rick tell a manufacturer that they suck. lol happy Easter 😂
I try to make a difference.lol
Doing a maintenance video on an ice cream machine would be awesome
Rick please never stop being you! Hope you had a Happy E!
😁 people have never been able to handle the full me. It has to be administered in small doses. Easter was good, had food, family and God time.
For those newer style delfield units. From factory, they cycle the evaporator fans on and off. Inside the control section you’re able to jump out the fans and have them run 24/7. Customers complained a lot back whenever Delfield decided to go to their r290 units. I’ve seen the same thing with True as well, true is slightly more complicated to get the fans to run 24/7 but it’s doable. Thanks for sharing
Thanks, that’s good to know. I knew the R290 true units did it but wasn’t sure about the Delfield.
Rick, Another amazing instructional video! Thanks for sharing ! Be safe !!
I saw those browning belts in your truck. That’s all I ever use anymore , great belts :)
Great video as well !!
That’s the main brand we use here as well. Thanks for watching!
Sounds like you have had a long week or something. Grumpin a little more than usual 😂. These videos have never disappointed in all the years i've watched.
I know 😆. Sometimes I just leave in things I normally cut out. It’s a fine balance. You get yelled at if you bitch but sometimes you just don’t care if you piss the world off. 🤟😂
@@HVACRSurvival ""just don’t care if you piss the world off.""
I need that T-shirt.
Hey hey we make some good shit here in Canada 😂
Walk in are working fine now
Great job has always Rick. Happy Easter
ice cream maintenance would be awesome
get some 90* quick disconnects for the end of your hoses. my dad always used them to minimize refrigerant loss on the screwing on and off of the hoses...
Those won’t hold up to 410a. I had them, they didn’t last. The ball valves last the longest.
@@HVACRSurvival Did not know that about the 410A, he got out of the contractor business before the 410A became standard. I've seen HVACR Videos use an Appion core depressor tool that might work then. Looks small enough to get into tight spaces and will only allow refrigerant flow one the depressor is screwed down.
@@terranhightower341 i’ve been using those valve core depressor tools recently from Appion and I gotta say I like them a lot, but even though they’re small, you might have a hard time fitting them in certain types of systems.
Never like the Kokpak set up for anything. They don't even give you enough room for a Schrader depressor tool either. Always have to give it some manipulation to make room.
Those snap disk switches always fail, i see it a lot on the Manitowoc condensers, always go with the adjustable switch when its out of warranty, they will outlast the unit.
Good fix Rick.
HAPPY EASTER
One thing that i didn't get, when you tried to install the swivel tee, you pumped it down and hooked up the suction hose and u installed it without losing pressure, why was it spraying earlier and not after? I understand that suction was low because of the pump down but what happened to the pressure on the liquid line?
It might sound stupid question but i m new to refrigeration and have learned a lot from you! thanks and keep up the good work!!
The place that I pumped it down at was on the receivers liquid valve. The valve I hooked it up at was after that valve. There was no refrigerant there or very little where I put the swivel tee.
@@HVACRSurvival makes sense, thanks!
Good job Rick, Happy Easter.
Happy Easter John!
Love the video as always great work. I want to see maintenance on a ice cream machine
Did this same repair on a kolpak freezer but the low pressure so I had to remount that liquid line to fit the tee on the suction
Needless to say I absolutely laughed and felt your pain when you say it’s an absolute trash design
Happy Easter. Good video.
Well, Rick, look at this from the bright side. At least this was easier work than fixing that supermarket coil you've posted recently. 😅
You're gruff, but lovable. Thanks for the vid. Love your work.
I appreciate that!👍👍🤜🤛😊
That freezer had tell tale signs of a bad defrost termination/fan delay control, or that ice was formed while trying to cool the walkin cooler...we will never know, or will we.
I agree. We will see
@@HVACRSurvival I edited my poor grammar while I read your reply...my ocd kicked in lol
Great job brother Happy Easter
How do you really feel about Kolpak Nice job as always ... Happy Easter to you & family ... Thx
A good idea is to add 50ml of sulphuric acid to the compressor before regassing to reduce corrosion
I don’t understand?
Was expecting some flashy beats at the beginning of the video, but the end is fine too. Regardless, nice video ;)
I’m looking to change things. Not sure to what
You're the man, videos are always entertaining
Happy Easter
Great video Rick! Not a fan of the snap diak fan cycle switches either.
👍💪❄️🇺🇸 Tennessee moonshine. Happy Easter
Great Video. Thank you for sharing
Thanks for watching!
Hey great video. Do you have a link for that service wrench. I have been looking for the 7in one for a while, but no one ever tells the dimensions in their description. BtW used your code to get the FIELDPIECE probe set. Thanx.
trutechtools.com/yellow-jacket-60615-3-8-x-1-2-square-ratchet/?srsltid=AfmBOoqcDPr8HrmqLBu3s6pO47BGkiH3h5K-1kGo2Hf3GkYqTo2tW-qWAQM?aff=13
Happy Easter, wats a good brand for evap coils n condenser units ?
Not a fan of Kolpak either. Most of them come with a pre charged lineset that some out of town installers coil up on the roof 🫠😂
those fan cycle controls don't like snow have to put them in a plastic bag to keep blowing snow out I'm in minnesota
Best and easiest to use controller on the market. If you can’t use that one I feel bad for you haha
What area do you work in great video 😅
North Western Ohio
Brass caps are only good with a brass washer inside.
Thats new to me. I have seen copper flare washers in some.
Where do you get your paint marker from
Amazon or eBay. Whoever is cheaper. Uni-paint blue
What are your thoughts on ESP evaporators? Starting to see them way more
It’s the future. It’s fine if you have spare parts.
Warm meat is not good 😅. Nice job, Rick!
Are the new locking gasketed caps ok for hold pressure on low side? I have a stripped schrader port that leaks so must rely on sealed cap. Thx
They usually have a rubber gasket, there is a flair 1/4 to 1/4 fitting that would work that has a new Schrader core or a swivel tee will work.
That's what I use that way the flare seals up against existing port.
good option given situation thx again@@HVACRSurvival
If it was a DG, they would still sell the spolied food
The suction port placement is just par for the course now, bad design, trash equipment, poor installers on and on and on.
Have you ever thought about taking a stationary type job? At least the equipment is yours for good and you can do whatever you need to do to it and customize it
the 13 people who disliked this video's brain no worki worki
Normally you can’t see that? My average is 97-98% positive so I don’t mind when the majority are that high.
@@HVACRSurvival i have a extension that makes me able to see dislikes
👍👍👍
If your based out of Ohio may have been my company that installed that 😂 a421s and kolpak. Agreed though shit design
Was it a pizza place originally?
@@HVACRSurvival The call you were at or my company? Lol unsure but we install a lot of those Kolpak condenser/evaps with that control. We are all over the place but mainly NE Ohio
Kolpak owned by Manitowoc or the other way around 🤷🏻♂️ 🗑️ . A good ole Tecumseh or Copeland condensing would’ve been better in my opinion 🤷🏻♂️.
I didn’t look up their history far as who their own by? I agree I’ll take either one of those other condensing any day before this.
Ya those style KOLPAK condensing units are horseshit for serviceability. Bottom of the barrel units
169 thumbs uP
Noticed you changed the name of the video . Kick bait Reeeee !!!
whine whine whine, would you like some cheese? 🤣🤣
couldn't resist the temptation, but yeah, everything is very poorly designed anymore and servicing is not on the list of things in play. 🙄
I’m a champion at bitching.
Theses engineer's never work on them so they don't care and build as cheap as they can that is the bottom line
True.
God those are such garbage.
Love your videos but man you're whiny on this one. It's funny at first but got annoying as it went on. Maybe shoulda stayed home that day or left the camera in the truck.
Fair enough ✌️ 👍👍