The Dual Purpose Channel Liner Tool and the Glock Channel Liner
ฝัง
- เผยแพร่เมื่อ 24 ก.ค. 2024
- In this video Lenny Magill shows a Glock part that many don't even know exists: the Glock Firing Pin Channel Liner. Lenny demonstrates how to use GlockStore's Dual Purpose Channel Liner tool to remove and replace the Channel Liner.
The Dual Purpose Channel Liner Tool is our item #8169:
www.glockstore.com/Dual-Purpo...
The Glock Firing Pin Channel Liner is our item #6128:
www.glockstore.com/Glock-Firi... - แนวปฏิบัติและการใช้ชีวิต
Even though I always experience horrible costumer service from the Glockstore I can't deny that Lenny has hand down the best ever tutorials for doing anything on a Glock, basically free armorer course if you watch a bunch of the videos, so thanks for that!
Ordered a set of parts from the Glockstore, about a year ago. It came, as an empty package. I called, and disputed. They shipped again. Empty package again. Will never order from them again.
Glock store is the best never had a issues
same they didn’t even respond to my email
@@tazsnuts99I’ve never had an issue with them either 👍🏽
its amazing how this guy turns what should be a 3-5 min video into a 20 - 45 min video...
Lenny has been doing this for a long time, great information every time.
Kudos to the guys in the machine shop!!! Will look into purchasing one!!! Glock perfection!!! :-)
Very cool. Love to see the detailed knowledge you have of Glocks.
Thanks for another great video Lenny. My thought - Have the machine shop put a depth ring (marker) around the channel liner tool so that the installer will know it's properly seated? That way, those who install get it right everytime. I could hear the difference in sound when you fully seated it. - Some folks are hard of hearing :-)
Lenny, good job on the video. You should throw in a channel liner with each installation tool purchased.
Informative video. Sound effects make it worth watching a second time.
Tool and liner for $4.99 at Brownells. $30 at Glock store.
Great video lesson. Thanks much.
This the fastest way I was able to remove my Glock channel liner without damaging it... if you have a plastic/wood full size arrow in your possession (or borrow one, buy one) take the metal arrowhead off and then stick the arrow shaft into the liner and pull it out... this took me less than 5 seconds to do! Hope this helps!
another great video thanks
Thank you for the information
Thanks for the info 😊
Super informatives Video danke
Lenny I like your sound effects. 😄 Also I would use a brass hammer instead of a steel one in order not to damage the threads on the tool.
How do you fix worn lower frame guides. I need to ADD metal to build up the groves on a P228 Thanks 😊
Lenny, What are your thoughts on using an oil impregnated bronze bushing for a channel liner? I understand the OEM is inexpensive but on the high end, I wouldn't think there would be much of a wear issue. BTW, great video's. I've had a GLOCK for years but have learned more from you in just a short time.
Cool new video!
Can I reuse channel liner after removing with this tool? Or do I need to just get a new one? Changing parts to a custom slide
Thinking of getting some cerakote done from a very reputable company but it really surprised me that they told me the way they pull the Chanel liner they can usually re use it. Makes a little weary because how would that be possible?
Lookin great brother
Helloooo! So my question is. I bought the GS G43 slide. Do I have to this with my slides?
Have the channel liners bought multiples because the 1st I tried folded on the lip when trying to seat it. This was with another channel liner tool. Bought a few more liners and the glockstore tool. That liner with the glockstore tool folded on the lip as well. I am starting to question if the channel itself is even milled wide enough to accept a channel liner.
BTW this is a Wraith RMR Cut Slide - G19 Size from 80%
Any help resolving this issue would be appreciated.
I have a stuck liner, even with a tool it won't budge 😭 this slide has never been shot and I have reason to believe while I was building it it's either not in correctly or it's damaged. Thinking of maybe dropping some oil in it and give it another try tomorrow
Good tool for gunsmiths and people who likes to service their Glock. Dirt can get in the Glock when out hunting fishing and camping. Or if you are in the military. If you are a mechanic so vapors from chemicals can damage the plastics of your firearms. But a clean environment the part should be fine. Just put your hand on top of your refrigerator or cabinets than throw in powder residue. I knew a man who raced cars he would change his oil before he started a race. Ask why and he said oil is cheaper than engines.
Wonder if you could just use a polymer punch to do the same?
NEVER KNEW IT WAS THERE!!!
I just had problems with the channel liner yesterday.
How reliable are the metal liners and sleaves ???
what happens if you put the liner in backwards? I didnt realize there was a front and back to the liner.. I just know my liner slipped easily onto my plastic channel liner tool and the liner itself slipped easily into the hole.. I didnt even need to pound it in. I was able to push it in easily with my hands/tool. I probably got lucky and put the correct end of the channel liner facing down into the hole.. but just wondering what if I didnt? I guess the aftermarket slide I bought made the hole a bit larger so I didnt have to pound the liner in with a mallet.
I’m watching videos now because I am in the same spot as you, easy install but no idea about front/back. Did yours end up firing ok?
Is this for Gen 5 glocks as well
thanks
Is the tool back in stock?
You wanna know my hack for putting in the channel liner ...A hollowed out Bic ball point click pen.
Great video as always.. and I thought it was 34 parts.
Gen 5 have 34 parts
Front sight has 2 screw and sight??? A+ on the spring cups good video
Do the spring cups count as one or two?
nevermind. lol
Just curious why wouldn’t they make The channel liner in stainless or aluminum wouldn’t that be better than plastic
It’s actually surprising how well those stronger plastics hold up to abuse especially when you take in extreme weather conditions going from hot to cold or cold to hot and then the vibration from the slide racking and all that other stuff, metal might crack easier than plastic in the same way a polymer frame will last longer than a 1911 frame unless it’s a really high end 1911.
It's to reduce friction and wear on the firing pin spring. Metal on metal contact will wear the spring a lot faster than metal on plastic.
Technically there are 26 internal parts because you also have the slide cover plate that is an external part.
One side of it is exposed, so by your logic, extractor would be an external part too. Which is fine by me
the liner is there because without it the cups wont stay put they squish past the edge on the firing pin.
You might have installed your cups wrong
In your video you say it’s 3/16 threads. Those threads look more like 5/16 ❓
I used a bic pen... flawless
Had to think about that... You tapped it down using a bic pen. Very nice.
Another bic pen hack
Dammit
When I'm screwin it in, my pull out game is 100%. Wait what were we talking about again?
32!!!!
Cool Prooo
Thought I was doing something wrong, so looked at this video. Nope, I just had to clamp a pair of vice grips to the tool and take a hammer to them. I beat the shit out of it before it came out
Ah ha the slide cover is actually two parts lol
I said 32 parts. If the Glock is 31 without the magazine & I count the whole magazine as 1, I get 32. 😁
You only counted 2 for the sights. You forgot to count the front sight screw!
Isn't there 37? There's a screw in the front sight.
I guessed 32 parts 😏
How about a current update on the SS80? It’s getting really old. All we hear is
“in two weeks”
K. Moore Semper Fi Stop crying, get your refund like they offered and buy else where.
Rob no thanks. I have spent ALOT of money on parts and I want the SS80. I’m not wrong wanting to be kept current with how much money I have spent. But thanks for your comment back.
K. Moore Semper Fi You are extremely unprofessional if this is how you handle your business. When I have a issue I contact the company directly through phone or email, I don't make a mockery on a video unrelated to my order... you look foolish making comments on a video that no one will respond too... Lenny has proven time and time again.. he READS emails!
Ezra Brooks lol!! 😂
Rob yes extremely unprofessional. Riiight.... well I have contacted GlockStore MANY MANY MANY TIMES and for the last oh 4 months i get promised it will be out and shipping in two weeks. I am not being unprofessional by asking for a current update from Leny not from his employees that keeps promising product shipment and then never ships. I have spent over $1000. On parts for building the SS80. Obviously calling and emails don’t work on looking for an honest update from the owner of a product and company that is making empty promises. As for professionalism. I am a disabled United States Marine Veteran. I have given ALOT for my country and the people in it. So I don’t need you chiming in with your opinion. When I am trying to get a response from a company about an issue that many people are having an issue with.
How do y’all don’t have a channel liner in stock? Is a dam piece of plastic dam
Lenny, you folks do a great job and I really appreciate and enjoy the videos, but this is another twenty minute video that should have been five minutes long...
I was close I said 32
I HAVE COUNTED MANY TIMES I SAID 26 NOT KNOWING ABOUT THE CHANNEL PART.
I don't like the plastic liner part of the Glock design.
EDIT...IT IS IN! THE LETTER IS IN!
NEWS TOMORROW. OFFICIAL NEWS, THAT IS.
SS80? No news? We have to hear something soon?! I just keep telling myself I'll give them another week...here's to hoping...
Ezra Brooks bro they issued refunds.... Where the fuck have you been?
Not paying attention maybe? I didnt get one!
No..I'm right..they offered refunds, yes, to people who chose not to wait anymore. I'm waiting it out. Why not at this point? I'll get my money back if it doesn't end up happening. I have faith in that.
#SS80CORE
Patience pays off
36 parts in a glock