Replacing a broken ferrule on a Viking Siege carbon fiber shaft
ฝัง
- เผยแพร่เมื่อ 6 พ.ย. 2024
- Replacing a broken ferrule on a Viking Siege carbon fiber shaft and installing a Samsara break jump tip using a mini lathe.
Check out my Facebook page -
www.facebook.c...
eBay Store -
www.ebay.com/u...
Shaft Collet Set - www.ebay.com/i...
Tip Shaper - www.ebay.com/i...
Tip Shaping Guide - www.ebay.com/i...
Shaping Guide now in blue! - www.ebay.com/i...
![โอ้เธอช่าง... - บี้เดอะสกา ft. ต๋อง เทวัญ (Prod. by ป๋าเพชร) [Official MV]](http://i.ytimg.com/vi/zbWhiLFmVL0/mqdefault.jpg)
I love it looks good im a fan of the black ferrules on my carbon shafts. Great job keep up the videos.
@@Gr1mTh3R34p3r Thank you!
I have a mucci from the early 90s. I wish i got 2 shafts , but i was young and didnt have much cash , it took me 3 months too pay for the stick with 1. I broke with it everytime i played and i played for years. 9ball. Its the only stick that i didnt break the ferrel. All my 'cheaper " cues broke eventually
Good job man🎉
welke vloeistof gebruik je met het oorstokje , en welk nut heeft dit. top video
@luclambrechts3001 I use Tiger Liquid Burnisher on the qtip. I use it to seal up the sides of the tip. The liquid and heat cause the tip to seal itself and make the sides nice and shiny. Thanks for commenting.
Hello please protect them from cue green what is it called
May I ask what this machine is called and where one can buy it?
@@wiegandkreuzpaintner6376 It is called a mini lathe. Here is a link to the one that I bought. Thanks for commenting.
Hi, I have a question hope you can answer, How do you taper the ferrule if the shaft have a slight taper? The machine cuts straight and it won't follow the taper of the shaft. Hope it makes sense
@warrente66 Ideally, you wouldn't have to taper the ferrule. That is unless you are talking about a snooker cue or something. If you need to taper the ferrule, sanding it down would be the way I would go about it. Thanks for commenting.
How did you get that vault plate to stay there without a very small hole through it?The ones I’ve done wouldn’t stay because of air pressure,and what material is that,it didn’t cut like tomahawk?
@Dugnew After I apply the epoxy and insert the vault plate. I apply pressure to the vault plate using the flat face of the tool post. You can see that at the 12:03 mark. The shaft will sit there under pressure until the epoxy cures. Normally, they will set for at least 12 hours. I will also note that this shaft's threaded insert was open, not sealed. Even though it was filled with foam, it might have allowed enough air to escape as I inserted the vault plate, preventing the back pressure. That said, I have also replaced the ferrule on a Cuetec Cynergy shaft, which was sealed, using the same type of vault plate, the same installation method, and had no issues with that one either.
The material I am using for the vault plate is cotton phenolic. It is incredibly light but extremely strong.
Thanks for commenting.
How did you know how thick you are cutting when you are making the ferrule? you didn't use a caliper to check if the diameter fits into the shaft, does your machine have some sort of measuring guide?
@warrente66 My lathe does not have any kind of measuring guide on it. At the 9:00 mark you can see what I do. Once I start to get close, I will turn off the lathe and do a test fit. I don't show it every time in the video, but I will do it quite a bit until it fits perfectly. Thanks for commenting.
what glue did you use to install the new vaultplate?
@@berghy0922 I use Devcon 2 ton epoxy. Thanks for commenting.
Wow I thought those were indestructible
@@Jmmac104 Definitely not. The ferrule was actually separating from the shaft. It seems that the glue failed internally. Thanks for commenting.
What happend to the carbon surface? Did someone tried to sand it with 80grit?😅
@@tkreiner1902 Your guess is as good as mine. Lol
Why not simply `part the tip off` and then drill and bore for the new tip.
@dinosauralan.9486 Carbon fiber shafts are hollow tubes that are filled with foam. Putting a tip on without any support behind it would eventually drive the tip into the shaft. The carbon fiber shafts don't necessarily need something as large as a typical ferrule on a wooden shaft, but they still need something to fill the end of the shaft and a hard flat surface to glue the tip to. Thanks for commenting.
Why don't they have removable tips?
@stevevenus1 A short answer to this question would be that quality pool cues need quality tips and also ferrules. The tip needs to be affixed to the ferrule, and the ferrule needs to be securely attached to the cue in order for the player to get feedback, aka "feel," out of every shot they take. Thanks for commenting.