Easy LS Cam swap without pulling the heads!
ฝัง
- เผยแพร่เมื่อ 16 พ.ค. 2020
- Dowel size is 5/16
Steve Cash:
/ stevecash83
Website: www.PremiumFuelMag.com
Please follow us on Instagram @premiumFuelMag
Check out our drift build on Instagram @PFM_Drift_Fox
Hit us up on Facebook: / premiumfuel - ยานยนต์และพาหนะ
About to do a cam swap on my trans am and man you helped me more then any vid I have seen! Thanks!
Awesome tutorial. However, I will say, I have indeed replaced an oil pump without taking the oil pan off. Have to be careful to not drop the bolt but all you need is a small wrench to fit in the small gap and you good to go.
Great video. Thanks for tutorial. Short, sweet and to the point....
Great video, I’m considering upgrading my trailblazer ls stock 5.3
Very thoughtful tribute at the end. God bless.
Well done video!! One of the best on TH-cam
Great vid loved every minute of it.
Thanks for the walk through man 👍 I'm just about to do this on my Holden Commodore (Australian GM) that has an LS1
thank you for this! this video is going to save me alot of time
You were clenching your cheeks on that one bud 😂😂 Good job
yeah buddy!
Good work stu!
Nice...u make it look easy...I gotta bring my ls to a machine shop to put cam in.
Awesome video!! Thanks for the tips
The wooden dowels slayed me. 😂😂😂😂😂🎉🎉🎉🎉
You did a great job with this video!
thanks!
Excellent video! Came here because I heard that Gen III Hemi cam swap could be done in a similar way without removing heads if your not changing lifters. Anyway, just appreciated your explanation. Car sounds bad ass by the way!
good luck with it
Nice work broski! I'm planning on DIY camming my ZL1/LSA. I hope it's the same deal inside the LSA. Your engine/exhaust sounds totally bitchen at the end of the video pulling away! The dedication was a classy thoughtful gesture. You're a good DEWD!
Thank you sir. The LSA is EXACTLY the same as what i have underneath, it's just a little more work for you getting your blower off.
@@Sgt.Slides Oh no kidding? The blower has to come off for a cam swap on on the LSA?
Great video!
Awesome video, thanks mate 👍
Awesome job I’m going to do this in my ls1 s10 job
Really Great Video! Thanks!
Thank you answered a lot of questions
Just subscribed! Awesome video man 💯
Thx for the sub!
What I did 3 cams. On my 01 myself teal green flip flop z28 stock suspension grudge car. And no the lifters stay up in lifter tray. Only if you have to change springs will you have to even touch the valve covers heads or intake. A Ls cam swop is easy. Like the channel but for Real Gm guys like myself it's no need to compare Ford to Gm . It throws off the enjoyment of your videos thanks. God Gm ls lt FTW
Great video.
Nice video straight to the point I'm thinking of putting a cam in my LT1 1995 Corvette would the Corvette have those holes
on an LT1, you can access the lifters with the intake removed, so you won't need this trick.
Thank you for the video. It helps out a lot. Did you just torque the rocker arms down or go by firing order?
the correct way would be to do them one at a time while rotating the motor. I didn't do it that way and it was fine.
This was really helpful! Hopefully I can do this on my L83.
very nice explanation thanks
Thank you, I’m about to pull the cam on my boat
Nice video! A buddy’s LS truck supposedly dropped a lifter / cam. I plan to do this step to see how bad of shape the cam is in before pulling heads to replace the lifters. If everything is trash (not knowing how long it was bad) we’ll figure something else out.
if something is coming apart in there, you're going to have to pull the heads at a bare minimum.
@@Sgt.Slides I was just hoping to diagnose the problem before tearing the heads down, to help with an accurate repair quote. The cam should show the irregular wear, right?
Thanks you very much!! First Timer
Ford... Powered by testosterone
What engines have you worked on where the heads have to come off for a cam swap? SBC, BBC, mopar, and Ford basically every pushrod V8 ever made only needs the intake removed (up top) to swap a cam. And the LS’s party trick since day one has been not having to yank the lifters to remove the cam
yeah, that's the point of this vid. The old push rods dont require the heads to be removed. Most people dont know this trick for the LS.
I was wondering how the rod trick worked I heard about. Thx
Very nice and informative video. I have a question for you, maybe you or someone else reading this can help me out. I am swapping ls1/t56 in 280z, and I would like to find out what cam is installed. Is there any markings on it, on the front or back end? What's the best and fastest way to find out? Thanks...
The information you want is usually printed on the back of the cam, which means you need to take the cam out to read it, and not all cams are labeled. Your best bet is to buy the cam that you want, swap it, and then try to get a machine shop to measure it for you so you can know the specs and sell it.
New subscriber!!! Just found this channel!!! VERY DETAILED!! Thumbs up!!!🔥🔥🔥 Can you do a video on tuning?
sorry, i don't really mess with the tuning aspect. I have a buddy that takes care of that for me.
@@Sgt.Slides oh ok gotcha!!
Awesome video! Does this also work with the GDI engines without removing the hpf pump?
Sorry, I don't have in depth experience with other motors. The LT style architecture may allow this, but you would have to take one apart and see first.
Thank you, well done video
My heart rate was up too bro
I had to change the cam in mind I just loosen the oil pump up a little bit to make sure I put it on the time in mark I like the video and where did you purchase those sticks from or did you have them made
I got em from lowes in the wood section, you can probably find them in craft stores as well.
How do the dowels hold the lifters in place,,,,,?
When you turn the cam to push up the lifters…you can’t push in the dowel unless the lifters are up, is that right?
Great video. Anyone do this on a gen 1 CTSV? I feel like there’s less room in the front of these cars but I could be wrong. But yea, this is completely doable rather than taking it somewhere and not having your car for weeks and a hefty bill im sure of.
this won't free up room in front of the car, , but if as long as you can pull the cam with the engine block in the car, this method will work.
So i don’t have to spin the motor over to relieve pressure on the valve spring so I can take the rocker arm off?
you can if you want to add extra steps, you dont have to.
@@Sgt.Slides great & when i do that the valve would lift up to the head right?
@@GreatestHITS26 yes, when you remove the rocker, the valve goes up.
Hey quick question what size are those wooden sticks are they 3/8s
Hi there! I am a total newbie when it comes to, well all motor. I'm thinking heads, when should I change heads, and can I stick with the factory heads if I was to go with a "street stage2" cam.
It's best to refer to the recommendations of the cam you are buying.
Yeah I got a whole rebuild coming up in a couple of weeks..not looking forward to it...🏁
Would a stock 1999 silverado 6L have these holes behind the timing chain to run the dowel in aswell? Thanks in advance!
yes, they are the oil galleys that supply oil to the lifters.
What size are the rods to keep the lifters up?
5/16 OD ...
Do you kmow what size dowels you used for this? Awesome video, super straightfoward
im pretty sure i said it in the video, but if i didn't i don't remember.
Ugh I need to know too 😂
5/16"
What is the diameter of the wooden dowels you used?
My anxiety would get me if I used wood dowels. Is there any other material that could be used that might be more resistant to possibly snapping in there? Seems like it was a tight fit so would not want to risk it lol
there isn't really a risk of it snapping, unless you put a dowell in there that's already damaged, also, the point of using wood is to get a tight fit without causing internal abrasions, you do need a tight fit to press the lifters in place. . You would have to jam a metal rod in there to get a tight enough fit, and that would cause damage.
@@Sgt.Slides makes sense, thanks for clarifying.
You can buy a tool for this, a number of manufactures make these - steel or maybe aluminium? I think they actually slide into the step in the lifter body - between the lifter top and bottom "bearing' surfaces. Comp Cams, Aero Flow etc. do these. But for 1 off - dowl is cheapest, or if you can figure out actual required diameter steel rods?
nice....
Little late to the game but did you pull both valve covers and the other side of lifters too ?
yes, you have to do both sides.
The common problem of camshaft is that, lobe worn, due to lifter roller worn. So we need to remove head.
if there is a problem, like you described, you probably do need a more detailed tear down, but in my case this swap was for an upgrade.
What size Dowell rod?
Maybe fiberglass rods similar to tent pole..
Where did you find or get the dowels or those sticks from?
should be able to find them in any craft store or hardware store.
@@Sgt.Slides about what diameter would you say they are? I’m gettin ready to do a big cam on my Silverado so any help would be awesome
@@SuperCbr08 5/16
Great video thank you.
what size cam did you go with? how much lift
i went from a mystery cam that i got scammed on, to a BTR LS1 stage 3, or stage 4, i don't remember at the moment. I love this cam so much.
@@Sgt.Slides awesome man , love the vidoes . is this a 5.3? i currently have an iron 5.3 in my e30 but im switching it out for a l33 5.3 and doing the whole cam, trunion upgrades, etc and was recommended a btr ls stage 1 cam by my local motorsports shop for an every day easy driving car with some competition use but im debating wether i should go stage 2 or 3 since its behind a manual, etc
Awww yes time for me to be overconfident and completely fuck this process up thus having to do it the long way anyhow
if you mess up, it's worse than doing it the long way lol, you can't really mess up though, the lifters can't slide past the dowel
When you turn the cam to push up the lifters…you can’t push in the dowel unless the lifters are up, is that right?
Then the megadollar 'witchcraft'...tune.....
What size dowels did you use
I would like to know as well
5/16 dowel, that's an important bit of info lol
How long did you make the rods?
longer than the engine block, but also consider not too long to fit into the engine bay.
Thank you for the reply that helps a lot
What size wood dowel do you use
I believe 5/16
What size dowels did u use?
Dowel size is 5/16
what size steaks did you use
5/16
bro you got the crank pulley bolt off with a battery impact wth
this battery impact aint no joke, and my buddy's Milwaukee makes this one look like a toy.
Thanks for all the good videos. I have an 89 GT need a good mechanic I'm in laurel Md do know anyone . what is ur IG
PFM Drift Fox. Sorry I don't know any good mechanics that do simple stuff without ripping you off. I do all of my own basic work.
Tf is going on with your haor man
did it to annoy my wife lol
dude that is clever. I think id get some thinner dowels tho.
If you use thinner dowells, your lifters will shoot right into the oil pan when you pull the cam out. or at best shuft and block you from re installing the cam. this size presses the lifters in place so they dont fall.
This guy said it would take him a week to do a cam swap ? Lmfao I literally pulled both heads and all lifters and rockers and switched cam and it took me a total of 8 hours basically from sun up to sundown it was actually the coolest thing I’ve ever done I love taking engines apart something about it calms my a.d.h.d
not everyone can afford to spend 8 hrs straight in the garage wrenching. at this point in my life, an 8 hr job is going to take me 2 weeks.