DIY Sim Racing Pedals (3D Printed)

แชร์
ฝัง
  • เผยแพร่เมื่อ 5 ธ.ค. 2020
  • In this video i will show you how to make a simulator pedal set yourself. I used a 3D printer to make the pedal set. You can find all the materials I used below.
    Materials for this pedals: a.co/9iYMlyf
    My favorite sim racing equipment on amazon: a.co/fSUxQDF
    3D Models Files: bit.ly/2Hp8hgM
    Schematic: bit.ly/2Hp8hgM
    - 40x40 Square T-Profile 6mm Mounting Rod Profile
    *3 pcs 300 mm - bit.ly/3oo9QLy
    *2 pcs 400 mm - bit.ly/3qxoi5Q
    - 6 pcs L Shape Inner Joints: bit.ly/2VGu3QJ
    - 4 pcs Profile Covers: bit.ly/39QQiLV
    - 18 pcs M5 T Sliding Nuts: bit.ly/3lLe66d
    - 3 pcs 10K Potantiometer: bit.ly/3kpT5x6
    - Throttle Spring OD: 28mm L:80mm
    - Brake Spring OD:28 mm L:80 (Harder than Throttle)
    - Clutch Sprint OD:28 mm L:80 (Harder than Throttle)
    - Cables: bit.ly/3qxpGW5
    - Allen Keys: bit.ly/33QE0iP
    - 23x38 cm 5mm Thickness Wood
    - 23x38 cm Floor Covering Carpet
    - 18 pcs M5x16 mm Hex Cap Head Screw
    - 6 pcs M5x20 mm Hex Cap Head Screw
    - 6 pcs M4x40 mm Hex Cap Head Screw
    - 3 pcs M5x40 mm Hex Cap Head Screw
    - 3 pcs M5x35 mm Hex Cap Head Screw
    - 6 pcs M3x16 mm Hex Cap Head Screw
    - 12 pcs M5 Selflocking Nuts - bit.ly/2VGEunc
    - 6 pcs M4 Selflocking Nuts - bit.ly/2VGEunc
    - 6 pcs M3 Selflocking Nuts - bit.ly/2VGEunc
    🛠️ Tools:
    - Ender 3 V2 3D Printer: bit.ly/3mPeEcG
    - 3D Filament: bit.ly/33NPp32
    - Cutting Mat: bit.ly/39JQdcY
    - Minleaf ML-BD2 710W Bench Drill: bit.ly/3lLR2UP
    - Soldering Iron: bit.ly/36OIubE
    - Solder: bit.ly/33QSyyS
    Instagram: / ilgeipek
  • วิทยาศาสตร์และเทคโนโลยี

ความคิดเห็น • 144

  • @ajw0685
    @ajw0685 2 ปีที่แล้ว +3

    This is awesome and I'm printing out a set now. Have you thought about running fillets around all the top edges? That way you wouldn't have to razor blade the edges.

  • @dhiasmemyself
    @dhiasmemyself 2 ปีที่แล้ว +1

    Wow.. been trying to make a long lasting pedals... seems your have made one... about going to print it now thank you for sharing !!

  • @bumas3825
    @bumas3825 3 ปีที่แล้ว +8

    what a high-quality job! Fascinating, good job!!

  • @aidenpearce4216
    @aidenpearce4216 ปีที่แล้ว +4

    How is the pot shaft coupled with the spur gear?
    Also, is there a standard stiffness for spring?
    Also also, why does the clutch pedal have a shaft inside the spring and others don't?

  • @EvilVitJoker
    @EvilVitJoker 2 ปีที่แล้ว +1

    I slightly modified and made your design. Thank you for sharing

  • @ViralVibe-hu9ly
    @ViralVibe-hu9ly 5 หลายเดือนก่อน

    Thank you very mutch for all i have make them and this is sick❤❤

  • @GaryMcKinnonUFO
    @GaryMcKinnonUFO 2 ปีที่แล้ว +1

    Lovely build, thanks for sharing, liked and subbed.

  • @AM-ob7yi
    @AM-ob7yi 2 ปีที่แล้ว +4

    Did you also make the steering wheel setup? Also any plans for making an h pattern shifter to go along with the two? :)

  • @sub-arts128
    @sub-arts128 2 ปีที่แล้ว +1

    great project! this ist, what i was looking for. i disassembled an old pedal-unit from a thrustmaster steering wheel. the potis are the same. i assume, they run on 5v, cause you wired it to the arduino, right? so what is mmjoy2? as far, as i understand, its an interface for arduino, so you dont not have to write your own sketch, and it provides a virtuell joystick, that windows can "see", right? i want to use this for MAME.

  • @disho8111
    @disho8111 2 ปีที่แล้ว

    oven spring hinges work great

  • @malikmartin
    @malikmartin 3 ปีที่แล้ว +81

    I can already see my feet pounding the brake pedal to dust.

    • @wiktorjaworski1710
      @wiktorjaworski1710 2 ปีที่แล้ว +2

      me too, i have european size 45 xD

    • @void3923
      @void3923 2 ปีที่แล้ว +7

      what you using the brakes for man? should only be using the accelerator for MORE POOOWWWWEEERRRR

    • @shatterpointgames
      @shatterpointgames 2 ปีที่แล้ว +1

      @@void3923 Brakes are used for slowing down usually

    • @void3923
      @void3923 2 ปีที่แล้ว +17

      @@shatterpointgames wtf is slowing down?

  • @iibrahiim
    @iibrahiim 2 ปีที่แล้ว

    Maşallah, çıtayı arşa koymuşsunuz 👍👏👏

  • @toolzification
    @toolzification 3 ปีที่แล้ว +1

    Nice build! Do you also have a link to the sketch?

  • @user-nq2ex3ic3s
    @user-nq2ex3ic3s 7 หลายเดือนก่อน

    i'm bouta make my own whole diy setup

  • @lordsanityfree
    @lordsanityfree 3 ปีที่แล้ว +4

    Can you link a source for the springs?

  • @hentauigacha6147
    @hentauigacha6147 2 ปีที่แล้ว

    thanks for the video, really motivate me to do this racing video game controller setup. i want to ask if i can also connect the potentiometer for steering wheel with the pedals to 1 arduino leonardo pro micro ? thanks

  • @LO_FLI
    @LO_FLI 2 ปีที่แล้ว +2

    Nice racing shoes! Could you use a load cell for the brake instead of a potentiometer? Awesome build, never done a Arduino project before but I don't own pedals or a wheel ATM so I'm tempted to give this a try!

    • @Dudik28
      @Dudik28 2 ปีที่แล้ว +1

      Yes, you can use a load cell too. It outputs a signal similar to a potentiometer. The harder you press the higher the signal, which the Arduino can read easily.

  • @CHIRAG_FPV
    @CHIRAG_FPV 3 ปีที่แล้ว +5

    Hall effect sensors give more precise actions might be fine for eurotruck but it is required for racing games

  • @57uyo
    @57uyo 2 หลายเดือนก่อน

    Hi, mate! This project saved me ton of time both in design and print as quickly I needed pedals to repair a Logitech Momo set for a friend. I upgraded them with RC shocks and am pretty happy how it turned out. I wanted to ask - what is the licensing for that? I would like to share my extension of the design so other people can download and use it for free too if possible! Cheers ;)

  • @kiwiflyer3797
    @kiwiflyer3797 ปีที่แล้ว +1

    what microcontroller that you use for this?

  • @123rolle
    @123rolle 2 ปีที่แล้ว

    Do you have link for those springs? How thick spring wire did you use?

  • @AllenRJoseph
    @AllenRJoseph 2 ปีที่แล้ว +2

    where can i get the springs?

  • @DudeIngenious5215
    @DudeIngenious5215 4 หลายเดือนก่อน

    what type of arduino did you use for this project?

  • @sserdar415
    @sserdar415 3 ปีที่แล้ว

    Çok güzel olmuş eline sağlık.
    Stl dosyaları arında debriyaj pedalı yok. Diğerlerinden farklı olarak yayın içinde bir parça var. Malzeme listesine eklermisin.
    Debriyaj pedalı ve arka parçayı ekleyebilirmisin?

  • @daturadj001
    @daturadj001 2 ปีที่แล้ว +1

    Podrias crear el modelado para instalar un sensor hall? seria genial, saludos

  • @hanswurst3811
    @hanswurst3811 ปีที่แล้ว

    where are the STL files for the clutch spring thing ? thanks :D

  • @mateoguerin2449
    @mateoguerin2449 ปีที่แล้ว

    Ilge, for what are the gerber files?? because you didn't use it on the pedals

  • @Erdemtrk7
    @Erdemtrk7 3 ปีที่แล้ว +3

    Güzel olmuş devamını bekliyorum

  • @RFXCasey
    @RFXCasey ปีที่แล้ว +1

    One thing I'd do different is Hall effect sensors instead of pots but good job, these came out great. How are they holding up 2 years later?

    • @ilgeipek_en
      @ilgeipek_en  ปีที่แล้ว +1

      I actually do these projects by developing them at different levels, from simple to difficult. It will be improved in the next versions. thanks for your comment

  • @okandemirbaykal5597
    @okandemirbaykal5597 2 ปีที่แล้ว +1

    Fusion veya STEP dosyalarını paylaşma şansınız olur mu? Mümkünse elimdeki 2020 profillere uyarlamak istiyorum da.

  • @stachu0257
    @stachu0257 ปีที่แล้ว +1

    Hey, can I use Arduino nano it's like a clone to Arduino pro micro I think

  • @kanyaahshopid5758
    @kanyaahshopid5758 3 ปีที่แล้ว +2

    great preject.. thanks for share

  • @rendererprocess9167
    @rendererprocess9167 3 ปีที่แล้ว +1

    Approved 👍

  • @flamed_flips919
    @flamed_flips919 4 หลายเดือนก่อน

    what pcb did you use?

  • @ygalion
    @ygalion 2 ปีที่แล้ว

    i wonder how long does PLA hold all this

  • @barkis4195
    @barkis4195 ปีที่แล้ว

    Where did you find those springs?

  • @xxxx-ei7gc
    @xxxx-ei7gc 3 ปีที่แล้ว +2

    THANK U VERY MUCH, i wanna next film but with H-shifter, would you do it?

  • @user-hj9by6ci7q
    @user-hj9by6ci7q 10 หลายเดือนก่อน

    Is there any other way to operate this build with a arduino uno ?

  • @eninja8152
    @eninja8152 ปีที่แล้ว

    Can you explain how you got the PC to read the input from the potentiometers. Im trying to do this but don't know what code to write for the computer to regonize this as a controller :( I'm lost id be willing to talk to anyone over discord if they know how

  • @johnsowerby6061
    @johnsowerby6061 ปีที่แล้ว

    could you tell me where to buy Brake Spring OD:28 mm L:80 please

  • @nicolasdebiaggi776
    @nicolasdebiaggi776 ปีที่แล้ว

    Hi how its going? can i ask you for the fusion 360 files? i would like to make a few modifications

  • @ow3nnnh
    @ow3nnnh 6 หลายเดือนก่อน

    hi, what code did you use for the arduino?

  • @ishanatapattu3278
    @ishanatapattu3278 3 ปีที่แล้ว

    good work !

  • @hadilotf580
    @hadilotf580 2 ปีที่แล้ว

    I used this with arduino uno running unojoy and it works

  • @aksha_rr4438
    @aksha_rr4438 ปีที่แล้ว

    Sir can you make shifter and hand break

  • @x1101126
    @x1101126 2 ปีที่แล้ว

    Good job! What's that small IC chip you are using?

    • @truepennytv
      @truepennytv 2 ปีที่แล้ว

      If you are referring to the small blue one he wired all the potentiometers to, it's an Arduino Pro Micro. For most projects like this you would use a Pro Micro or possibly an Arduino Uno, as they can operate as keyboard / mouse / joystick on computers.

    • @jenshendriks9092
      @jenshendriks9092 2 ปีที่แล้ว

      @@truepennytv I believe an Uno doesn't have HID compatibility. The Leonardo does. I would suggest a teensy though. Since they can read potentiometers at a higher resolution. The Pro micro (and leonardo I believe) only do 10 bits (1024 values over the full range) where a teensy can do up to 16 bit I believe (or even 32 Idk). 16 bit would give you 4x the resolution so 4096 values over the full range. Especially if you're doing a wheel. You'll need a fast microprocessor for accurate high resolution encoder readouts. I'm building a wheel which uses a motor with an encoder on top of it that reads about 5 steps per degree of rotation. If you flick the wheel 180 degrees within half a second, you need to make sure that it won't miss any step of the encoder, cause if it happens too often it could result in a weird offset from straight.

  • @alperengul2578
    @alperengul2578 3 ปีที่แล้ว

    ilge abi normal kanalında yorumumu göremeyebilirsin diye bu kanalına yazıyorum sen kanalında bunu leonardo ile yapabilirsiniz demistin ben uno ile yaptım ama pedalları ahşap bir kasada yapmak istiyorum o kullandığın dişlilerin 2d çizimini alabilir miyim cnc kesim yaptıracağım da

  • @marcelmohrhardt2077
    @marcelmohrhardt2077 2 ปีที่แล้ว

    how can i buy the springs ?

  • @ymilord
    @ymilord 3 ปีที่แล้ว +1

    Hi. Can you post the f3d file?

  • @labform_championship6372
    @labform_championship6372 2 ปีที่แล้ว

    Where can i buy spring like this?!?! Help please:(((

  • @S60Team
    @S60Team 2 ปีที่แล้ว +5

    Hello! I printed these pedals and put them together. I noticed 2 problems: the springs fly out of the mountings. And the upper spring mount prevents the potentiometer gear from turning.

    • @southernstar4353
      @southernstar4353 2 ปีที่แล้ว +4

      He used glue to hold the springs in the mounts

  • @wilson3487
    @wilson3487 ปีที่แล้ว

    hey, do i need a breadboard and 2 resistors to make the connections ? like for the pedals and the steering wheel (with shifters but no ffb), and which resistors do i need ?

    • @ilgeipek_en
      @ilgeipek_en  ปีที่แล้ว

      Hey Wilson, you can get the details on my blog: ilgeipek.com/sim-racing/diy/pedals/

    • @wilson3487
      @wilson3487 ปีที่แล้ว

      @@ilgeipek_en really cool ! Thanks a lot

  • @sket123flamez7
    @sket123flamez7 2 ปีที่แล้ว

    hi what arduino code did u use

  • @ihahaoo
    @ihahaoo ปีที่แล้ว

    nice build ,now you only have to make a gearbox for your set :)

  • @chulian1819
    @chulian1819 2 ปีที่แล้ว

    This needs dejavu

  • @karolprzywitowski8827
    @karolprzywitowski8827 2 ปีที่แล้ว

    What cost is it?

  • @ViralVibe-hu9ly
    @ViralVibe-hu9ly 7 หลายเดือนก่อน

    I cant find springs

  • @hakangencel89
    @hakangencel89 3 ปีที่แล้ว +36

    Those springs are not enough for the immersion, apart from that build quality is top notch

    • @marcosdimoise8662
      @marcosdimoise8662 3 ปีที่แล้ว +6

      just buy a damper and increment in the project

    • @Sighman
      @Sighman 3 ปีที่แล้ว +2

      I need a set of pedals for a spare gaming rig - something to use with Mudrunner/Euro Truck and the like. These look fine for that purpose.

    • @szalonykierowca5870
      @szalonykierowca5870 2 ปีที่แล้ว +3

      @@marcosdimoise8662 what is a damper?

    • @FineBakedPastry
      @FineBakedPastry 2 ปีที่แล้ว +3

      @@szalonykierowca5870 an oil filled shock absorber to give the feel of a brake pedal.

  • @Driazinho
    @Driazinho 2 ปีที่แล้ว +2

    Ficou perfeito !

    • @Liimaplay
      @Liimaplay 6 หลายเดือนก่อน +1

      os gringo manja

  • @rajnishsinghaluhwalia2913
    @rajnishsinghaluhwalia2913 2 ปีที่แล้ว

    Great project i wanted to buy this from logitech but they have hiked the prices and i have a prusa so I'll make this for my birthday gift

  • @mervankaplan6218
    @mervankaplan6218 3 ปีที่แล้ว

    Abi kablolu kulaklık yapar mısın ?

  • @christophers.rafuse7107
    @christophers.rafuse7107 3 ปีที่แล้ว

    Gear stick next plz

  • @TercioTeles
    @TercioTeles 2 ปีที่แล้ว

    wow 💥

  • @dragonhatake3124
    @dragonhatake3124 3 ปีที่แล้ว +1

    So nais man! I want a steering wheel with force feedback and a H-Shifter! That will be awesome

  • @CHIRAG_FPV
    @CHIRAG_FPV 3 ปีที่แล้ว +1

    U read my mind

  • @overwatchprovods9281
    @overwatchprovods9281 2 ปีที่แล้ว

    I cannot get the games to recognize the mmjoy. They always say controller disconnected when using an input. Anyone else have this problem?

  • @seeindarkness
    @seeindarkness 3 ปีที่แล้ว

    Soon this will be the only way to drive an ICE car.

  • @sailhdulgeroglu914
    @sailhdulgeroglu914 3 ปีที่แล้ว

    Abi sana nasıl ulaşabilirim yerin nerde

  • @yasintohan7934
    @yasintohan7934 3 ปีที่แล้ว

    abi pedal gaz yayı silinmiş yok linki yenilermisin

  • @ivansit4578
    @ivansit4578 3 ปีที่แล้ว

    can u make a h shiter next vid

  • @thatcat5721
    @thatcat5721 2 ปีที่แล้ว

    potentiometer is a failure point, hall effect switch would not only be much easier, (cheaper), but it won't fail.

  • @KiminAnonim
    @KiminAnonim 3 ปีที่แล้ว

    Hocam DIY 3d printer projesi gelir mi acaba ? :D

    • @memeed3981
      @memeed3981 3 ปีที่แล้ว

      başkalarında gördüm ama adam işin uzmanı felandı ve pahalı ve karmaşıktı yapımı. bunun basitliğinde bişey gelirse gerçekten çok iyi olur

  • @TC_ReflexYT
    @TC_ReflexYT ปีที่แล้ว

    can you do handbrake?

    • @ilgeipek_en
      @ilgeipek_en  ปีที่แล้ว

      Sure! I will publish my handbrake video soon.

  • @epic_nonbinary_cheeseball
    @epic_nonbinary_cheeseball 2 ปีที่แล้ว

    damn these shoes bro

  • @fitchyyboi
    @fitchyyboi 2 ปีที่แล้ว

    How much would this cost me?

  • @domainexpansion6438
    @domainexpansion6438 3 ปีที่แล้ว

    what are the spring wire diameter anybody?

  • @bruvbruvbruv6191
    @bruvbruvbruv6191 3 ปีที่แล้ว +1

    Plz make a gt steering wheel

  • @klaggege7409
    @klaggege7409 ปีที่แล้ว

    Next is the shifter

  • @rashmikadeshan6705
    @rashmikadeshan6705 2 ปีที่แล้ว

    Hello, Can i use Arduino Uno R3?

    • @wiktorjaworski1710
      @wiktorjaworski1710 2 ปีที่แล้ว +1

      You can't....sort of. Arduino leonardo has USB HID controller, and Uno don't, so you will not be able to program/flash the Uno with the used software

    • @sh3ldox260
      @sh3ldox260 2 ปีที่แล้ว

      @@wiktorjaworski1710 wait did he use a nano or a pro mini I'm so confused

    • @wiktorjaworski1710
      @wiktorjaworski1710 2 ปีที่แล้ว

      @@sh3ldox260 he used arduino pro micro.

  • @bldsprt518
    @bldsprt518 3 ปีที่แล้ว

    Clever

  • @teddytheprogamer254
    @teddytheprogamer254 ปีที่แล้ว

    Shifter next 6 speed

  • @WhildChamp_74432
    @WhildChamp_74432 ปีที่แล้ว

    make a DIY shifter and e-brake when you can

  • @josueherrera8547
    @josueherrera8547 3 ปีที่แล้ว +1

    Falta el modelo 3D para el embrague, los demas estan bien

  • @yexo2394
    @yexo2394 3 ปีที่แล้ว

    Can i make it on arduino uno?

    • @ThomasLancheros-kg1nl
      @ThomasLancheros-kg1nl 3 ปีที่แล้ว

      i dont think so try getting a cheap Leonardo for like $15
      it also uses micro usb

  • @josueherrera8547
    @josueherrera8547 3 ปีที่แล้ว

    Alguien tiene el modelo 3D del embrague???

  • @hexaprasetya1121
    @hexaprasetya1121 3 ปีที่แล้ว

    im so waiting for the h shift and handbrake

  • @CHIRAG_FPV
    @CHIRAG_FPV 3 ปีที่แล้ว +1

    If u plan on doing 2nd version try using Hall effect sensors

    • @ThomasLancheros-kg1nl
      @ThomasLancheros-kg1nl 3 ปีที่แล้ว

      Don’t think it’ll work

    • @CHIRAG_FPV
      @CHIRAG_FPV 3 ปีที่แล้ว +3

      @@ThomasLancheros-kg1nl maybe your broke mind won’t work

    • @jenshendriks9092
      @jenshendriks9092 2 ปีที่แล้ว +3

      @@CHIRAG_FPV Damn. 2020 was a stressful year for you? What an unnecessary insult

    • @CHIRAG_FPV
      @CHIRAG_FPV 2 ปีที่แล้ว

      @@jenshendriks9092 @mr_beast 1098 dosent even know how it works

    • @jenshendriks9092
      @jenshendriks9092 2 ปีที่แล้ว +1

      @@CHIRAG_FPV Why do you care? XD

  • @egemenpekmezci6298
    @egemenpekmezci6298 ปีที่แล้ว

    bu sistemi forza horizona bağlayabilir miyiz

  • @yasintohan7934
    @yasintohan7934 2 ปีที่แล้ว

    abi gaz yayı linki atarmısın abiiiii

  • @MozTS
    @MozTS 3 ปีที่แล้ว +1

    1:31 D: don’t do that!!! It with break the tap off in the hole!!! Only hand tap threads in aluminum!!!

  • @ajdaunay2983
    @ajdaunay2983 3 ปีที่แล้ว +1

    where's the arduino code for the pedals please

    • @elimiller2658
      @elimiller2658 3 ปีที่แล้ว

      He's using MMJOY2. I believe it can be found on Git. MMJOY2 will program your Leonardo.

    • @ajdaunay2983
      @ajdaunay2983 3 ปีที่แล้ว

      @@elimiller2658 yeah but on the github there aren't any .ino files

    • @krzywypl
      @krzywypl 2 ปีที่แล้ว

      @@ajdaunay2983 did you see all movie? He shows that in 1st place that he put hex file to burn in arduino, then he started to make configuration of pedals

  • @Erdemtrk7
    @Erdemtrk7 3 ปีที่แล้ว +2

    Çok iyi

  • @mateoguerin2449
    @mateoguerin2449 ปีที่แล้ว

    And where is the arduino code?

  • @sorryfornoname2157
    @sorryfornoname2157 2 ปีที่แล้ว

    I dont want to be mean by why arent there f3d files? not everyone has access to the same resources dude. please share f3d if you still can

  • @yasintohan7934
    @yasintohan7934 3 ปีที่แล้ว

    ABİ PEDAL GAZI YAYINI LİNK ATARMISIN SİLİNMİŞ YAY

  • @fillman86
    @fillman86 2 ปีที่แล้ว

    I don't know why, but I was expecting load cell brakes

  • @cardosoall9666
    @cardosoall9666 3 ปีที่แล้ว

    up up top manoo

  • @enesozhan1252
    @enesozhan1252 3 ปีที่แล้ว +1

    İlk

  • @assasinoyuncu5642
    @assasinoyuncu5642 3 ปีที่แล้ว

    abi bana yardım edermisin

  • @that_guy550
    @that_guy550 10 หลายเดือนก่อน

    One rage and it is broken