I really like mine - just need to loctite or hot glue the canopy screws once adjusted to your liking - those suckers will vibrate right out the first day
Perfect little quad for in the house. I use a Frsky X 9 lite on D16 and it works fine. Also use the GNB 520mah batteries and GNB 650 batteries. Usually get around 5 minutes flight time with the 650's.
I’ve been flying this whoop since new year and I love it. I’ve been using GNB 520mAh LiHV and I got minimum 4 minutes of flight time with no puffing yet. Now with Project Mockingbird’s tune and JESC firmware it flies even better 👍🏻
I got it too. Very fun littlel drone. Also i got this 6X1 charger and its so eazy to charge all. And i buy this multiprotocol too because i got x9 lite.
I only fly my TH2 in 2s cose i got allot of 2s batterys, and there is the thing: Set the throttle limit in 80% and flash the esc in 48mhz to use the RPM filters. That gives me abut 4 min of flyght, 5mins on hobbering, whit 450mah 2 S batterys
I' flying the Freestyle 2, which I think is the same board, in D16 on an X9 Lite. You think it'll get more range if I get the multi protocol module and bind in D8?
I just got the Tinyhawk II for father's day, and do not know anything about them. Never had a drone before. I am trying to take baby steps here. Why are the 2s batteries that came with the drone trying to burn up the USB charger, when I try and plug the batteries into the charger?
Just bought one You should convert even for 1s to xt30..it will save your battery in the long run. And set your minimum voltage warning to 3.50 These 2 recommendations will prevent your battery from puffing. I bought 2s tattu hv 450 and made 1s out of them. All the best ...
Would you recommend using a small capacitor (e.g. 6.3 V 100-150 µF) for (1s) tiny whoops? The AIO whoop boards are packed with stuff. I guess the filtering is bad. A test would be very interessting!!!!
I had fun with mines. Lasted a month of hard use then one of the escs? went. The replacement board is $59.99. I may just get a whole new one and use this one for parts. Love it though. It took a beating too.
Good video. I will say however that six bank charger you're showing, I ordered one of these from RDQ and the AC side of it was DOA, got a replacement from them the other day and it worked for two or three charges out of it and the same thing happened to it. Don't know if it's just my bad luck or if this charger inherently has a bad AC port, I couldn't find any general complaints about it but I think a lot of people that have this charger are using the DC side only.
Does either charger you recommend actually support the ph2.0 connectors on the stock TH2 batteries? It's not listed specifically ("Micro,MX,JST,mCPX").
I haven’t been able to figure out how to set the quad to D16 mode, I try to change it in the configuration, but I can’t seem to find it to my X9 Lite, any tips?
@@geordiestreams8876 Plug it into the computer and connect to Betaflight. Go to the Configuration tab. Go down to the receiver section in the configuration tab and under receiver set it to FRSKY_X. The factory setting is FRSKY_D. That's D8 mode. If you want it in D16 then set it to FRSKY_X. Hit save and reboot. Make sure it saved the new setting. That should so it. Then you just have to bind it.
@@CarbonGlassMan Thanks for the reply! - so i put it into FRSKY_X mode, saved it rebooted, loaded it back up, put it into bind mode - then my controller is set on Internal RF, ACCST D16 mode, tried binding on CH1-8 with both telem ON and OFF It just never binds.. - ive got a D8 module coming tomorrow, but thought if it would work in D16 i should try get that done
@@geordiestreams8876 For me I had to keep the quad plugged into betaflight and go to the CLI and type bind_rx. That along with hitting bind on the transmitter always worked for me.
I just got this rtf and 2 days in and with full battery the tinyhawk would drop rpms or volts, don’t know which one is it? when try to hover it for only few seconds!!!! Any help be appreciated.
Just got mine. It is my first drone, and it isn’t worth crap. It takes off in random directions and plants itself against a wall or ceiling every single flight. The user manual isn’t much help as it gives no instructions on use of the batteries. I really wish I had used that money somewhere else.
Seems like a strange response. First drone and you think it's crap. As with any non GPS controlled drone, they do not track perfect unless you use the trims. That being said- this drone is not meant to just hover. You need to actively being moving around. I hope you've figured this out by now but if not- I hope this helps!
I just got my drone yesterday and I was having the same problem you are, but I figured it was because I was inside my tiny little room trying to fly this. This is also my first drone so both me and you need to get used to flying and controlling this, I suggest to go outside, keep it low to the ground and try to stay steady. Just get the feel of the drone.
Reasonable video , But gave up watching due to the awful repetitive music ... Yes I'm listening with headphones .... Why , Just why do people who make a review video where they are talking " Always " choose to ruin the video by awfull Repetitive music 👎
TinyHawk-II: bit.ly/2vEbMtM
6x Lipo Charger: bit.ly/2QFbWu6
4x Lipo Charger: bit.ly/2CoIxdR
5pcs 1S Battery: bit.ly/2J3IqIe
I really like mine - just need to loctite or hot glue the canopy screws once adjusted to your liking - those suckers will vibrate right out the first day
Perfect little quad for in the house. I use a Frsky X 9 lite on D16 and it works fine. Also use the GNB 520mah batteries and GNB 650 batteries. Usually get around 5 minutes flight time with the 650's.
I flashed jesc 48, removed leds, now it gives me 4.5 minutes flight time. My minimum voltage is 3.4v-3.5v
Wow thats a big improvement thanks for the tip.
what is jesc 48 and how did you do it?
@@ELValenin th-cam.com/video/NgBJJG0slM4/w-d-xo.html
At 7:29: yes, you can use D16 on the latest FrSky radios
I have this and the freestyle 2. Love them. They're especially nice when you can't get out to do some real flying.
I’ve been flying this whoop since new year and I love it. I’ve been using GNB 520mAh LiHV and I got minimum 4 minutes of flight time with no puffing yet. Now with Project Mockingbird’s tune and JESC firmware it flies even better 👍🏻
Try the GNB 650mah batteries, I've been getting around 5 minutes+ flight time.
Did you need to mod the connector on the GNB lipo to fit the PH2.0 plug or you added an xt30 connector on the tinyhawk?
@@ja-rod9759 1S or 2S?
Jason John the battery comes with PH2.0 so no mod needed
I got it too. Very fun littlel drone. Also i got this 6X1 charger and its so eazy to charge all. And i buy this multiprotocol too because i got x9 lite.
I only fly my TH2 in 2s cose i got allot of 2s batterys, and there is the thing: Set the throttle limit in 80% and flash the esc in 48mhz to use the RPM filters. That gives me abut 4 min of flyght, 5mins on hobbering, whit 450mah 2 S batterys
I' flying the Freestyle 2, which I think is the same board, in D16 on an X9 Lite. You think it'll get more range if I get the multi protocol module and bind in D8?
no need to change pids. It set by itself when the battery is plugged
I just got the Tinyhawk II for father's day, and do not know anything about them. Never had a drone before. I am trying to take baby steps here. Why are the 2s batteries that came with the drone trying to burn up the USB charger, when I try and plug the batteries into the charger?
You dont recommend to use it with x9 lite taranis?i was considering the radiomaster tx16 radio...
Have you tried slapping bigger batteries on it?
Just bought one
You should convert even for 1s to xt30..it will save your battery in the long run.
And set your minimum voltage warning to 3.50
These 2 recommendations will prevent your battery from puffing.
I bought 2s tattu hv 450 and made 1s out of them.
All the best ...
The camera in IT IS amazing
Would you recommend using a small capacitor (e.g. 6.3 V 100-150 µF) for (1s) tiny whoops? The AIO whoop boards are packed with stuff. I guess the filtering is bad.
A test would be very interessting!!!!
I had fun with mines. Lasted a month of hard use then one of the escs? went. The replacement board is $59.99. I may just get a whole new one and use this one for parts. Love it though. It took a beating too.
Was you flying 2s? Pid and rate profile 2?
@@HerbertBrasil yes. But I was fairly new to fpv and had a lot of hard crashes before it broke
Thank you
It doesn't matter if you crash or not. Ypu get about a month of use out of this tinyhawk 2. AIO/ESC is garbage.
@@twp3029 im never flying 2s, wanna know soon or later
I’m not worried about flight time cos I’ve got like 14 batteries
Good video. I will say however that six bank charger you're showing, I ordered one of these from RDQ and the AC side of it was DOA, got a replacement from them the other day and it worked for two or three charges out of it and the same thing happened to it.
Don't know if it's just my bad luck or if this charger inherently has a bad AC port, I couldn't find any general complaints about it but I think a lot of people that have this charger are using the DC side only.
I use the AC 98% of the time
@@DroneMesh Yeah? I don't know what the deal is then, I got two of them from RDQ both of the AC sides quit working right away.
Does either charger you recommend actually support the ph2.0 connectors on the stock TH2 batteries? It's not listed specifically ("Micro,MX,JST,mCPX").
I'm using D16 on my X9 Lite radio for the Tinyhawk 2. I bought that module but haven't figured out how to use it yet.
I haven’t been able to figure out how to set the quad to D16 mode, I try to change it in the configuration, but I can’t seem to find it to my X9 Lite, any tips?
@@geordiestreams8876 Plug it into the computer and connect to Betaflight. Go to the Configuration tab. Go down to the receiver section in the configuration tab and under receiver set it to FRSKY_X. The factory setting is FRSKY_D. That's D8 mode. If you want it in D16 then set it to FRSKY_X. Hit save and reboot. Make sure it saved the new setting. That should so it. Then you just have to bind it.
@@CarbonGlassMan Thanks for the reply! - so i put it into FRSKY_X mode, saved it rebooted, loaded it back up, put it into bind mode - then my controller is set on Internal RF, ACCST D16 mode, tried binding on CH1-8 with both telem ON and OFF
It just never binds.. - ive got a D8 module coming tomorrow, but thought if it would work in D16 i should try get that done
@@geordiestreams8876 For me I had to keep the quad plugged into betaflight and go to the CLI and type bind_rx. That along with hitting bind on the transmitter always worked for me.
why do you think when I even gently bump my drone it just drops ,,I've checked over everything and can't find anything loose
I just got this rtf and 2 days in and with full battery the tinyhawk would drop rpms or volts, don’t know which one is it? when try to hover it for only few seconds!!!!
Any help be appreciated.
I really like the new colour grade ;)
Would you take this outdoors?
Looks like JST-PH connector
you say eachine tinyhawk in your intro ;-)
Nice great vid
I tried my tiny hawk 2 out for first time today… very sensitive controls watching u fly looks like a far away goal for me :/
You don’t have to change pid profiles. The drone changes automatically when you plug in a battery.
Can some one PLEASE explain 1s and 2s, and which battery is which?
Oh the eachine tinyhawk now Ahahaha
"Eachine TinyHawk II" lol
roflcopters
Just got mine. It is my first drone, and it isn’t worth crap. It takes off in random directions and plants itself against a wall or ceiling every single flight. The user manual isn’t much help as it gives no instructions on use of the batteries. I really wish I had used that money somewhere else.
Seems like a strange response. First drone and you think it's crap. As with any non GPS controlled drone, they do not track perfect unless you use the trims. That being said- this drone is not meant to just hover. You need to actively being moving around. I hope you've figured this out by now but if not- I hope this helps!
I just got my drone yesterday and I was having the same problem you are, but I figured it was because I was inside my tiny little room trying to fly this. This is also my first drone so both me and you need to get used to flying and controlling this, I suggest to go outside, keep it low to the ground and try to stay steady. Just get the feel of the drone.
Don't buy this. The ESC fails after a month of use. Gone through 3. EMAX needs to fix this.
Were you running 1s or 2s?
Eachine? Lol i know what ya meant 😉
Reasonable video , But gave up watching due to the awful repetitive music ... Yes I'm listening with headphones .... Why , Just why do people who make a review video where they are talking " Always " choose to ruin the video by awfull Repetitive music 👎