Can u explain briefly how the 3 inches of lift kept wheels from rubbing ? Just curious because it's so much info saying it cant be done jus curious to what has to be done
I was wondering the same thing. I hear that using Axle bushings instead of needle bearings on your inner drive shaft when doing a lift will make it a permanent fix on the inner drive shaft. Will be doing a lift in the summer and I will be using the Axle bushings as they are machined for a perfect fit.
Mine has the scooped Hood in the sport model it's millennium silver it's got the 410 rear end with the locker still runs and drives like new cuz it's been maintained well
Dear 88Routes, I hope this message finds you well. I am a big fan of your TH-cam channel and have been following your content closely. Your videos are incredibly helpful and inspiring, especially for those of us looking to upgrade our vehicles. I am currently working on my 1997 Toyota 4Runner SR5 4x4 and am planning to upgrade the suspension. Based on your expertise, I would greatly appreciate your advice on the following: Bilstein 5100 Front Coils: Could you please share which Bilstein 5100 front coils you used for your 4Runner? Any specific part numbers or details about the setup would be very helpful. Additionally, any insights on how they perform both on-road and off-road would be much appreciated. OME Rear Coils Recommendation: I'm also looking for a suitable set of OME (Old Man Emu) rear coils to complement the Bilstein 5100s. Which OME rear coils would you recommend for achieving a balanced lift and improved ride quality on my 4Runner? Thank you for your time and assistance. Your guidance will be instrumental in helping me make the right choices for my suspension upgrade. Best regards, Raymond
I really like the look on the first 3rd gen 4runner, good tire size for the lift, but I have to think the 285/70/17's (32.7") will rub. I've read in numerous places that 265/75/16 (31.65") are the largest a 3rd gen 4runner can take w/out rubbing. I have 265/70/17's (31.61") on my 3rd gen almost exactly like this one (minus the lift) and they come super close to rubbing on the bottom of the plastic fender flares when the front wheels are turned. Although appropriating funds towards a sweet set of wheels instead of aftermarket UCA's tells me this rig is more interested in form than function. It does look nice!
285s can fit without rubbing, you just have to know what you’re doing. It’s in the alignment, wheel offset, and other factors. It’s been proven false that suspension lifts help you clear bigger tires because the suspension will still flex to the same spots, If you research on the forums, people have fit this size on 4Runners with no suspension lift at all. That’s because the rubbing occurs at a certain amount of uptravel, this uptravel can be limited by an extended bump stop or A 1 inch body lift can help to move the body away from the tire and keep the full range of travel. but it can be done even without any lift by tubbing the fender wells and pushing the suspension through its range of motion to find spots where the tires hit. UCAs MAY help fit 33s because they allow for more caster adjustment I believe which also might effect tire clearance. Tinkerers adventure has a video on fitting larger tires I recommend you check out for Toyota ifs but that video is on an FJ so adjustments may slightly be different. Personally though when I go for 33s I’ll be doing 255/85r16s. The skinny pizza cutter 33s. Better mileage, less rotating mass, BFG makes this size, easier on drive train and the contact patch has been proven to be very similar and in some scenarios even better for traction.
Question: Do you think I can run 285s with a 2.5” lift using 6112s in the front, 5160s in the back, SPC uca, with a running board delete on a 2001 SR5 with factory flares? - without rub ofc.
If the owner of the first 4Runner (silver w/bronze wheels) reads this .....where did you get those Rear Tail lights? I have the same 4Runner a 2000 SR5. 88Rotors did my lift as well. Love those 3rd Gens.
please do you guys know that exact same front bumper with flares part number of the first grey 4 runner sr5 sport edition? i highly appreciate the help
With the constant changes with new importing tariffs and material costs, we try not to post prices on here because it may change depending on when people read it. Please contact us by phone or e-mail for accurate quotes for when you need it. We can be reached at 626-442-3150 and are available 10AM-5PM PDT weekdays and 10AM-4PM PDT Saturdays. We can also be reached by e-mail 24/7 at sales@88rotors.com. Thank you for your interest in our products/services!
Bilstein/OME Stage 1 Lift Kit - 3rd Gen 4Runner (1996-02) SELECT FRONT CONFIGURATION: Option 3: OME 883 SELECT REAR CONFIGURATION: Option 3: OME 891 Assemble Front Shocks and Coils ($190.00): Yes I want my front shocks and coils assembled with new top hats Add 5MM Trim Spacers ($54.00): Add Two spacers
The reason they show the 5100 lift kit often is because its an affordable option and one of the most popular because of its price point. I would go 6112s all day! Not even a question.
SUBSCRIBE AND LIKE FOR MORE DAILY VIDEOS!
You guys do great videos but more specific part numbers on shocks and which models springs would be helpful, I might swing by. im in socal as well!!!
It’s beautiful! That generation is the best looking suv
Can u explain briefly how the 3 inches of lift kept wheels from rubbing ? Just curious because it's so much info saying it cant be done jus curious to what has to be done
I was wondering the same thing.
I hear that using Axle bushings instead of needle bearings on your inner drive shaft when doing a lift will make it a permanent fix on the inner drive shaft.
Will be doing a lift in the summer and I will be using the Axle bushings as they are machined for a perfect fit.
Hi, what is the wheel offset?
Mine has the scooped Hood in the sport model it's millennium silver it's got the 410 rear end with the locker still runs and drives like new cuz it's been maintained well
Just got done with mine love it, can’t wait for my 4.88 and front auto locker.
Dear 88Routes,
I hope this message finds you well. I am a big fan of your TH-cam channel and have been following your content closely. Your videos are incredibly helpful and inspiring, especially for those of us looking to upgrade our vehicles.
I am currently working on my 1997 Toyota 4Runner SR5 4x4 and am planning to upgrade the suspension. Based on your expertise, I would greatly appreciate your advice on the following:
Bilstein 5100 Front Coils:
Could you please share which Bilstein 5100 front coils you used for your 4Runner? Any specific part numbers or details about the setup would be very helpful. Additionally, any insights on how they perform both on-road and off-road would be much appreciated.
OME Rear Coils Recommendation:
I'm also looking for a suitable set of OME (Old Man Emu) rear coils to complement the Bilstein 5100s. Which OME rear coils would you recommend for achieving a balanced lift and improved ride quality on my 4Runner?
Thank you for your time and assistance. Your guidance will be instrumental in helping me make the right choices for my suspension upgrade.
Best regards,
Raymond
to clean basically my dream set up
Same except mines rusting and i dont want to put that much money into it
I really like the look on the first 3rd gen 4runner, good tire size for the lift, but I have to think the 285/70/17's (32.7") will rub. I've read in numerous places that 265/75/16 (31.65") are the largest a 3rd gen 4runner can take w/out rubbing. I have 265/70/17's (31.61") on my 3rd gen almost exactly like this one (minus the lift) and they come super close to rubbing on the bottom of the plastic fender flares when the front wheels are turned. Although appropriating funds towards a sweet set of wheels instead of aftermarket UCA's tells me this rig is more interested in form than function. It does look nice!
I’m wondering how 265/70/17’s looks on a third gen. Can you post a video?? I’ll subscribe to you In case you do upload.
I was thinking the same thing!
I'm running 265/70/17 it's not bad, I want to go a bit bigger
I want 285s
285s can fit without rubbing, you just have to know what you’re doing. It’s in the alignment, wheel offset, and other factors. It’s been proven false that suspension lifts help you clear bigger tires because the suspension will still flex to the same spots, If you research on the forums, people have fit this size on 4Runners with no suspension lift at all. That’s because the rubbing occurs at a certain amount of uptravel, this uptravel can be limited by an extended bump stop or A 1 inch body lift can help to move the body away from the tire and keep the full range of travel. but it can be done even without any lift by tubbing the fender wells and pushing the suspension through its range of motion to find spots where the tires hit. UCAs MAY help fit 33s because they allow for more caster adjustment I believe which also might effect tire clearance. Tinkerers adventure has a video on fitting larger tires I recommend you check out for Toyota ifs but that video is on an FJ so adjustments may slightly be different.
Personally though when I go for 33s I’ll be doing 255/85r16s. The skinny pizza cutter 33s. Better mileage, less rotating mass, BFG makes this size, easier on drive train and the contact patch has been proven to be very similar and in some scenarios even better for traction.
Still need a project runner? 1996 4runner SR5 with 204k miles on it.
Question:
Do you think I can run 285s with a 2.5” lift using 6112s in the front, 5160s in the back, SPC uca, with a running board delete on a 2001 SR5 with factory flares? - without rub ofc.
Any rubbing issues with the tires?
3 inch should clear 33” which this is 28.6” so I’d guess yes
You need smaller tires I had the exact tire size and they rub like crazy
4:43 land cruiser buddy
and it clearly says it too! lol
Take those runners off and ull love how much better itll look!!!
I know this is just like a promo video, but you should actually show some of tube install process
I have a 2002 4runner in stock condition any recommendations on it
What size shock absorber did they use in the back?
So did you just put a Bilstien 5100 shocks on to make it that High? And the did you do a body mount chop on It to make the wheels fit? Thanks
And tires that i would like to get have to be good on rocks and mud? I ask because i am a 1st time 4runner owner
If the owner of the first 4Runner (silver w/bronze wheels) reads this .....where did you get those Rear Tail lights? I have the same 4Runner a 2000 SR5. 88Rotors did my lift as well. Love those 3rd Gens.
The one 4runner? They looked bronze in the shop and then outside looked gunmetal.
Greetings,with these tire setup dont need to change the differential ratio?
What offset are the RRW wheels on the 4runner?
What’s brand that rear coil
What part# OME springs are you using?
So, still no before and after pictures?? 🤷🏽♂️
Click here: 0:00 and 4:20?
0:10 and 2:06
What are the exact wheels and offset being used in the first 4runner. I tried searching up the 16 in rrw wheels but it says they're only for tacomas.
I have the Tacoma ones and no issues here.
Awesome thanks for sharing with us, thanks again.
whats the price on a job that was done on the first 4runner?
what is the offset of these wheels?
Hey what offset are the RRW wheels?
I have a 2002 4runner sr5 sport 4wd manual with 89k mikes on it it’s black with leather inside all stock 💯 it looks like new
Luck man i got a 2000 sr5 2wd 95k miles leather seats, mint, wish i had 4wd
Link for wheels and tires
Suggest suspension for my 3rd generation 4runner and tyres suggest.... I'm from Pakistan
What tires and wheels do you recomend for my 2nd gen 1994 4runner. And is a 3inch lift still to low or is it a perfect fit??
please do you guys know that exact same front bumper with flares part number of the first grey 4 runner sr5 sport edition? i highly appreciate the help
Hi will 285 65 16 rub on a 2.5" OME lift?
Подскажи а параметры литья вынос и ширина
Man Toyota's don't age!!
What’s the price of just a lift? I’m a first time 4runner owner and have never gotten lifts on any vehicle. Thanks
With the constant changes with new importing tariffs and material costs, we try not to post prices on here because it may change depending on when people read it. Please contact us by phone or e-mail for accurate quotes for when you need it. We can be reached at 626-442-3150 and are available 10AM-5PM PDT weekdays and 10AM-4PM PDT Saturdays. We can also be reached by e-mail 24/7 at sales@88rotors.com. Thank you for your interest in our products/services!
How much would this cost?
Offset ?
Beautiful job they look great 👍
I got a 2000 4Runner same color on the vid 4x4 3rz
No rubbing?
No rubbing boss
I can confirm that too, I have the same size tires and wheels and my car is stock. I’m getting a 3inch lift soon. But no rubbing what so ever.
Jeremiah Romero hard to believe. Mud terrain or all?
Whats the offset?!
Can you fit 16in TRD Wheels on the 3rd gen?
16” is what they come with from factory
All that non rust, makes me jealous!!!
what if you dont regear at 33's?
You’ll be fine without a regear. 33’s feel fine IMO
what are all the parts for this lift because i want this lift on my 4runner
Bilstein/OME Stage 1 Lift Kit - 3rd Gen 4Runner (1996-02)
SELECT FRONT CONFIGURATION:
Option 3: OME 883
SELECT REAR CONFIGURATION:
Option 3: OME 891
Assemble Front Shocks and Coils ($190.00):
Yes I want my front shocks and coils assembled with new top hats
Add 5MM Trim Spacers ($54.00):
Add Two spacers
Still looking for one??
I have a 3rd gen 4 runner if you wanna buy it. 2001black Color really clean
Information?
Send me a text 6156277038
How much does it cost for a mechanic or shop to install a lift kit
How much to lift 3" inch on a 2002 4runner
I paid $450 for mine, 3" on bilsteins adj, ome 906 in rear and highlander springs in front
Would this work on 2wd?
Why would you ever want to waste the money to do that to a 2wd?
Of course you can it’s your car your money just do whatever make you happy it’s gonna look nice n still 2wd can last longer
4 runner 1999 2002 king
I’m selling a 2001 3rd gen Fully stock. Gray in color. Has diff lock. Was used as a family car, no Rust. I’m located in NorCal.
Still for sale?
Bogdan Fedinchyk still for sale?
How much did you sell for, if you can share. Tnk u.
i have a pretty clean 3rd gen that I WONT SELL YOU!!! haha
Do you guys ever install any 6112/5160 setups?
We, sure do.
The reason they show the 5100 lift kit often is because its an affordable option and one of the most popular because of its price point. I would go 6112s all day! Not even a question.
So I have a 99 4cyl 4x4 what kind of lift and tire sizes would you recommend
I got a 99 limited with a locker for the right price im in North Carolina
i sent you guys an email but never got a response.
Nice!!!
Cool vid!! What songs you used in this video???
Have one
👍
@88Rotors I’ve got one for you. Let me know if y’all bought one or not.
Would you trade for 03 mustang gt ? 🤔
I have a 2001 4Runner sport I mite want to sell
I got a clean ‘00 Silver Sport I’m about to sell...
I’ll contact you guys soon!
I have 1999 limited 4runner 167k miles on it is in good conditions hit me up if ur interested
Jose Urias how much bro
3200$
Where you located clean title
@@Ibbys_Reviews irving tx
Yes is clean title
I have one
Good luck with mpg
If you're worried about MPG, you shouldn't be driving a truck in the first place.
Obviously can’t afford this type of setup if you can’t afford the gas 😂
You need to buy a month pass for your bus ride if you have to worry about mpg on a 4runner.
A re-gear will get help it get back some mpg’s. Love mine!! You can see the fuel needle go down when driving. LOL
La arruinaron levantando la es su tamaño normal de fabrica, no inventen