At the 8:46 mark where your screwing the bolt into the main body, on mime it looks like i have a needle vulave sticking in it. Is that right, because i can`t get that part off the main body?
You may be having delivery valve which is normally spring loaded valve, if the valve you see has spring on it, then is a delivery valve and you cannot remove it. It is responsible for building pressure in the injector till the injector opening pressure. You can take it apart, clean and reassemble the part for installation. Let me know if you need more support
@@agritechtv5134 Ok ,The part you are putting in at the 8:22 mark , inside of the nut part is the needle valve, I don`t see any spring in it. does it unscrew so I can clean it? (Finally got that part off the main, has the washer in it like you show) I don`t think whoever owned this before I did , ever had it apart because I had to heat up all the joints just to get it apart. Thanks
The way i do it is crack open connection at the nozzle then kick the tractor for about 4cycles to confirm all air are out then tight the connection back. This always clear the line, there is need to rectify the point of entry of the gas unless the fuel finish i the tank while the engine is running. If you did not loose your tank level then find where the gas came in and rectify else you will continue doing this procedure at all time
@@agritechtv5134 Ok, I will try that. I have a hard time starting this tractor even when when it was primed with fuel since I brought it. Book says it has a glow plug, but doesn`t say where it located?
I'm doing the same on a agcoplus deutz fahr 4 cylinder already cleaned fuel tanks and filters! Great job
Thank you
Too much back ground noise other wise it would be a good video
Thanks for the feedback, we will improve on the audio
Great job 👍
Thank you
At the 8:46 mark where your screwing the bolt into the main body, on mime it looks like i have a needle vulave sticking in it. Is that right, because i can`t get that part off the main body?
You may be having delivery valve which is normally spring loaded valve, if the valve you see has spring on it, then is a delivery valve and you cannot remove it. It is responsible for building pressure in the injector till the injector opening pressure. You can take it apart, clean and reassemble the part for installation. Let me know if you need more support
@@agritechtv5134 Ok ,The part you are putting in at the 8:22 mark , inside of the nut part is the needle valve, I don`t see any spring in it. does it unscrew so I can clean it? (Finally got that part off the main, has the washer in it like you show) I don`t think whoever owned this before I did , ever had it apart because I had to heat up all the joints just to get it apart. Thanks
@@agritechtv5134 How do you take it apart, does it screw in?
@@agritechtv5134 I don`t think the prior owners ever worked on these as I had to take a torch and heat everything up to get it apart
@@agritechtv5134 the part at the 8:12 is the part i am talking about
One more ? How do you prime the fuel system so the tractor starts without runny my battery down?
The way i do it is crack open connection at the nozzle then kick the tractor for about 4cycles to confirm all air are out then tight the connection back. This always clear the line, there is need to rectify the point of entry of the gas unless the fuel finish i the tank while the engine is running. If you did not loose your tank level then find where the gas came in and rectify else you will continue doing this procedure at all time
@@agritechtv5134 Ok, I will try that. I have a hard time starting this tractor even when when it was primed with fuel since I brought it. Book says it has a glow plug, but doesn`t say where it located?
Potrzebuje numer tej końcówki wtryskiwacza
Sorry i did not have the part number, i did not change mine, only cleaned and installed
На моєму моторі стоять dn12sd12, на Алі є дуже непогані аналоги від ideeseel.