In October 2022 I removed the injectors from my Suzuki GV (with the Renault 1.9 engine) and having unscrewed a couple of the needle ends so as to clean the five holes, I was perplexed as to how to re-assemble the parts and was unaware that the tip is separate from the holder because it was so gummed up with carbon. I drove to three diesel specialists asking how to reassemble them and was told “You’ll have to part exchange them and pay £165 GBP for each.” I came home feeling very depressed and then found the answer in this video. Thanks for saving me a lot of cash.
Great vid. Been quoted $2400 to replace 4 injectors on a 2012 Audi A3 1.6 Tdi. No one in West Oz offers a cleaning service. This is a great vid showing how to save money. Well Done.. !!
Excellent Video. I enjoyed watching. Your Macro shots were impressive and you've got a engaging style. Watched till the end and then said awh when it was over :)
I appreciate your video. I've cleaned VW and other injectors with an home style denture ultrasonic cleaner - works great! . Water and soap is all I find it needs. A few seconds will knock the big stuff off. I usually hit them with about 30 minutes or so. LUBE THEM RIGHT AFTER REMOVAL (or they will micro rust). In reassembly I flush them liberally with clean diesel fuel or cheap spray can penetrating oil. I don't recommend using a wire on the holes as it can mess up the spray pattern . The pintle pin should float in the bore with no friction,. - Be careful not to let it fall out ! Keep every thing VERY clean and flush with diesel while assembling.
THAT was absolutely Brilliant!!!! My only negative feedback is that on another video it stated to make sure your working area is 'Meticulously' clean, and they stressed how important that is. Almost clean room clean for working on injectors. I have the injectors you showed so this is perfect for me. Thank you. Again, Excellent video.
I'm going to take my Mersedes to som1 to clean the Injectors. I was scared before I'm now relieved and hope they going to be fine. This video saved me a lot of money. Tnx.
I love these diy videos. I dared to touch one of my common rail injectors on the electrical side because it was leaking from there. I didn't know where to put the small ball that was on top of the actuator and had to send it to the shop. They fixed it up but it's still leaking. This video gives me a lot of confidence, will definitely do this sometime.
Appreciate your research. Good vid. I'll do mine. Having just paid £503.00 for two and now told I need another two. I'll service them myself. Thank you.
Excellent video! I am just about to do this with my 5 common rail injectors on Volvo d5 . This made my day. Methodical and explained everything with ease. Thanks!
Finally, I found a video that clearly shows how to disassemble, clean, and assemble a fuel injector (diesel injector). For the lack of parts name knowledge I would just say there are a two part nut base (one part to connect to the fuel port: the half part which houses the device with two circular alignment tab pins and the other half is used to house the injector needle), and a needle that atomized the fuel. I would hazard a guess that when the diesel fuel is under pressure it comes out through the needle as a vapor (atomized). The needle houses the pin, meaning there is a pin inside the needle, right? So the pin inside the needle controls the fuel delivery by moving up to plug the holes and moving down to let fuel pass. Right? Excellent video. 33 foot pound to tighten the nut of this certain diesel fuel injector using a TORQUE WRENCH. Wonderful, thank you so much for your time and sharing it with us.
AWESOME! Very informative video. If anybody knows what torch tip cleaners are I highly recommend a set of them because there is different size wires in there and it is the perfect carbator tool. Not only will clean carbs but any thing mechanical that has small holes that's got to be cleaned. Can buy from any wielding supply store. 😁
You can pick up carburettor jet cleaning kits for very little cost on eBay. But you must use a solvent because any seeds of carbon will move back down and clog the spray tip all over again.
Yay a good video, I’ve taken them totally apart before and they been fine, doing my PD injectors soon….. my local shop want £125 each to do them!! You can even buy new tips on line for them!!
I'm gonna save this video, so I can clean the fuel injector of my future YAMADA 22hp diesel engine, for my fishing boat soon. Philippines Thanks for sharing.
Thanks, this was very useful. You would be wise to keeps those solvents off your skin. They actually soak right through your skin and can have long range effects to you nervous system. The thinner stuff goes right through your gloves as well so I usually hold whatever I'm cleaning with long pliers. Just a tip. Thanks for making this video.
Most solvents are potentially dangerous but the really effective (but really nasty) stuff eg 111 trichloroethane and carbon tetrachloride are no longer available. However biodiesel is safe and a very effective solvent. There are many recipes on www. You can make a litre in a soda bottle. Just mix, shake and leave to settle.
WHAT A COOL VIDEO!!! Thank you SO much for this! I took my 20-year-old Mercedes to an "Injector Specialist" 3 years ago, who cleaned all 6 injectors for 400 Euros, that's about 442 US Dollars. Now, after watching your video 3 times, I'll do it myself. Although I'm a "machinist technician" I never dealt with injectors, I always thought it's a something very-very sensible thing, After watching your video, I will do it this (like you in your video) at the weekend myself, for sure, THANK YOU SO MUCH! Over here in Hungary, we don't have that cleaner, but I bought it on Amazon for 35 US Dollars incl. shipping, it will arrive tomorrow :-) I'm sooooo excited. Thank you once again!!! That "specialist" told me a fairytale about injectors.... "there are 2 very small balls inside it when you disassemble it, you may damage it, that's at least 1200 bucks for 6 injectors, etc..." Andeson, you're great, thanks a lot for this VERY DETAILED video, I can't thank you enough!!! I always get comments on my channel, that I speak and talk too much in detail, but you're my man, the truth is always in the small little details... What's the worse thing? I have to buy new injectors. But I don't care. You just empowered me :-) Now I don't even care if it gets broken, I'll try to do the same you did. If it gets broken I'll buy a new set, but it is definitely worth a try. Really Anderson, THANK YOU!!!!!!! (TheMaxAcceleratrion)
Yous did very good job explaining how to clean up and reuse injectors... any chance of polishing pin so it's a little harder for carbon to still too, also allowing it to move in and out more freely... Thanks for sharing
The proper way to do it is to drop the injectors into an Ultrasonic bath of diesel and detergent for an hour or two (overnight for the really bad ones), give them a rinse and you should be ready to go.
I was waiting for that comment. In general yes it is the way to open them but a steel wire in the holes and a steel wire brush are a big no no.... Yes and you have to dismantle them when cleaning with a ultra sonic cleaner. As well use nitrile gloves and a lubricant when touching them. Sweaty fingers can course corrosion!
Wow. My volvo penta 2001t just wont start. I've tried everything. Flushing fuel system' filters everything. Im confirmed enough to try this now. What's the worst than can happen at this stage. Thank you so so much
I saw your video,, I feel like can do same thing 😅,, I did (clean injectors) when I start the engine never working 😅,, recover with mechanic take €420 to retast and fix the injectors 😂 Thanks 👍
thnx mate good video, i just wonder how was your driving experience after cleaning all nozzels? and how many miles did you drive before u cleaned the nozzels ?
Thanks for the tip on how to separate the injector, I didn't have a Scooby, but im an expert at prodding things into holes to open them up , hence the reason I've got 4 kids to 3 women lol
Cool! I like fixing things if at all possible, if they have any life left in them. Right now Im fixing a siezed up air compressor off a wheel barrow compressor. The thing had sat for years tucked away in the shop and wasn't used because a hole had rusted into the bottom of one of the tanks. I fixed the hole with acetylene welding and cleaned out the fuel system to get the engine running again. The twin cylinder compressor ran very strong and would do 160 psi with ease so I liked having it on my work trailer. It would actually run a 1 inch tire gun just enough to take a truck tire off. The compressor was low on oil apparently which Id never thought to check and one day while running it on a 16 degree Farenheit day for just a few minutes before the compressor sadly locked up and came to a screeching halt. It has set for 3 years now taken apart and I got the idea that I would file the gaulding off the crank and recondition the rods with a brake hone. And what do you know? I have it back together now with smooth working rods and crank. I liked the compressor especially because I got it off the shelf and gave it life again. I gave it back its purpose. I made a place for it on my trailer. And I'm fixing to do it again.😎🙂
bunu yaptikdan sonra problem duzeldimi? kendi aracimizin enjokterlerini boyle temizlesek problem olmaz demi. kirlendigi zaman. bilgisayara baglatip kod felan girmeye gerek varmi? bazilari oyle diyorda. Tesekurler
![CAMPปลิ้น | EP.77[2/2] "รับทราบ" แก๊งเพื่อนรัก 10 ปี ที่ไปไหนก็มีตำนาน!](http://i.ytimg.com/vi/ifc0ofD51B0/mqdefault.jpg)
In October 2022 I removed the injectors from my Suzuki GV (with the Renault 1.9 engine) and having unscrewed a couple of the needle ends so as to clean the five holes, I was perplexed as to how to re-assemble the parts and was unaware that the tip is separate from the holder because it was so gummed up with carbon. I drove to three diesel specialists asking how to reassemble them and was told “You’ll have to part exchange them and pay £165 GBP for each.” I came home feeling very depressed and then found the answer in this video. Thanks for saving me a lot of cash.
Just thinking that a Renault engine is inside a Suzuki is depressing enough!!
Great vid. Been quoted $2400 to replace 4 injectors on a 2012 Audi A3 1.6 Tdi. No one in West Oz offers a cleaning service. This is a great vid showing how to save money. Well Done.. !!
Excellent Video. I enjoyed watching. Your Macro shots were impressive and you've got a engaging style. Watched till the end and then said awh when it was over :)
Thank you for taking the time to show this in detail. Very helpful!
I appreciate your video. I've cleaned VW and other injectors with an home style denture ultrasonic cleaner - works great! . Water and soap is all I find it needs. A few seconds will knock the big stuff off. I usually hit them with about 30 minutes or so. LUBE THEM RIGHT AFTER REMOVAL (or they will micro rust). In reassembly I flush them liberally with clean diesel fuel or cheap spray can penetrating oil. I don't recommend using a wire on the holes as it can mess up the spray pattern . The pintle pin should float in the bore with no friction,. - Be careful not to let it fall out ! Keep every thing VERY clean and flush with diesel while assembling.
Awesome video. I'm going to give all 4 injectors an overhaul now after 117,000 miles on the clock. Thanks for sharing !!
Thank you Anderson. Its a great video on cleaning diesel injectors. Opening of the injectors was awesome !!
I have used that product and put it in ultrasonic cleaning machine. I had great results in ten minutes .
awesome video mate
u sure got the subject
thanks that made this vid for us ... so helpfull
be well u and ur family !!
Brilliant! Thank you! That will be my next big job on my Rodeo TD , 2.8, 96 made great sense and can be duplicated thanks to your diligence! 👍😃✅
Great video started cleaning my injectors and thought best find a video yours was fantastic and we'll shown
Thank you 👍
THAT was absolutely Brilliant!!!! My only negative feedback is that on another video it stated to make sure your working area is 'Meticulously' clean, and they stressed how important that is. Almost clean room clean for working on injectors. I have the injectors you showed so this is perfect for me. Thank you. Again, Excellent video.
I was thinking that, too BUT... great video! I never thought of cleaning them but now... I will!
I'm going to take my Mersedes to som1 to clean the Injectors. I was scared before I'm now relieved and hope they going to be fine. This video saved me a lot of money. Tnx.
I love these diy videos. I dared to touch one of my common rail injectors on the electrical side because it was leaking from there. I didn't know where to put the small ball that was on top of the actuator and had to send it to the shop. They fixed it up but it's still leaking. This video gives me a lot of confidence, will definitely do this sometime.
Appreciate your research. Good vid. I'll do mine. Having just paid £503.00 for two and now told I need another two. I'll service them myself. Thank you.
How did you get on doing it yourself??
Thank you so much - very well explained
Just given me the inspiration to tackle my diesel injectors on my tddi 1.8 ford connect.
THANK YOU 🤞
Very good video. Thank you for sharing.
Excellent video! I am just about to do this with my 5 common rail injectors on Volvo d5 . This made my day. Methodical and explained everything with ease. Thanks!
Thanks for taking the time to do the video - very helpful
Finally, I found a video that clearly shows how to disassemble, clean, and assemble a fuel injector (diesel injector). For the lack of parts name knowledge I would just say there are a two part nut base (one part to connect to the fuel port: the half part which houses the device with two circular alignment tab pins and the other half is used to house the injector needle), and a needle that atomized the fuel. I would hazard a guess that when the diesel fuel is under pressure it comes out through the needle as a vapor (atomized). The needle houses the pin, meaning there is a pin inside the needle, right? So the pin inside the needle controls the fuel delivery by moving up to plug the holes and moving down to let fuel pass. Right? Excellent video. 33 foot pound to tighten the nut of this certain diesel fuel injector using a TORQUE WRENCH. Wonderful, thank you so much for your time and sharing it with us.
THANK YOU, VERY CLEAR, LEARNED A LOT FROM YOU, GOD BLESS!
Sir ji bohut bohut sukriya mera ek 5 hp desel machin hain abi injector karab hukor betra hain. Hum abi apka video ku dekor bohut kusi.
Very good info. Clear and concise. Thanks much.
excellent attention to detail, great video, Thankyou.
Great info here. Thanks for putting this up.
The best video and correct and explained seen so far thank you the problem with the injectors has been solved
Best video on TH-cam for cleaning injectors
AWESOME! Very informative video. If anybody knows what torch tip cleaners are I highly recommend a set of them because there is different size wires in there and it is the perfect carbator tool. Not only will clean carbs but any thing mechanical that has small holes that's got to be cleaned. Can buy from any wielding supply store. 😁
You can pick up carburettor jet cleaning kits for very little cost on eBay. But you must use a solvent because any seeds of carbon will move back down and clog the spray tip all over again.
Yay a good video, I’ve taken them totally apart before and they been fine, doing my PD injectors soon….. my local shop want £125 each to do them!! You can even buy new tips on line for them!!
Thanks for this. Very helpful.
Thank you I cleaned now my injectors and injectors knocking noise is gone and good performance great.....man
Was you car ticking when you accelerate or what?
Thank you Adorian for for sharing this ,explaining very clear .
thanks so much demonstration is very helpful and interesting
I'm gonna save this video, so I can clean the fuel injector of my future YAMADA 22hp diesel engine, for my fishing boat soon.
Philippines
Thanks for sharing.
Very helpful. Thank you so much. Ciao!
Nice, you help't my to create the idea how to clean my injector and you save my a lot of mony. Thnx bro
excellent video! Thanks for the lesson!
Excellent help. I have saved some money !
This is a very interesting video, very instructive. Thanks a lot, will help a lot
I enjoyed the video. BTW you can buy Brass music wire of different sizes. I'm surprised you don't use gloves, pretty dangerous chemicals there.
Thanks, this was very useful. You would be wise to keeps those solvents off your skin. They actually soak right through your skin and can have long range effects to you nervous system. The thinner stuff goes right through your gloves as well so I usually hold whatever I'm cleaning with long pliers. Just a tip. Thanks for making this video.
Great tip I can imagine they could cause auto immune diseases
Most solvents are potentially dangerous but the really effective (but really nasty) stuff eg 111 trichloroethane and carbon tetrachloride are no longer available.
However biodiesel is safe and a very effective solvent. There are many recipes on www. You can make a litre in a soda bottle. Just mix, shake and leave to settle.
They're using the red can of brake cleaner - the chlorinated stuff. I doubt their concerned with their health too much.
I done similar to you but I also put them into ultrasonic cleaner, I couldn’t believe the dirt that came off!!
thank you, nice video, very helpful.
THANK YOU TO TEACH US !!!!! FROM SPAIN.....
Enjoyed the video. very good advice
Thanks a lot for this "tutorial" it helped me saving 50€ euros.
God bless you ;)
That was a really good educational video
*Very good for the video I have been able to learn something new in relation to the injectors of my car.*
Awesome!! Learned a lot :)
Good Video. Learned a lot.
I enjoy watching the cleaning process. I will do that to my nozzles.
What a great informative video 😀
absolutely excellent video, I got a lot of good info from it, thanks :)
Brilliant idea with the wire to clean the holes 👍👍👍👍
WHAT A COOL VIDEO!!!
Thank you SO much for this!
I took my 20-year-old Mercedes to an "Injector Specialist" 3 years ago, who cleaned all 6 injectors for 400 Euros, that's about 442 US Dollars.
Now, after watching your video 3 times, I'll do it myself. Although I'm a "machinist technician" I never dealt with injectors, I always thought it's a something very-very sensible thing,
After watching your video, I will do it this (like you in your video) at the weekend myself, for sure,
THANK YOU SO MUCH!
Over here in Hungary, we don't have that cleaner, but I bought it on Amazon for 35 US Dollars incl. shipping, it will arrive tomorrow :-) I'm sooooo excited.
Thank you once again!!!
That "specialist" told me a fairytale about injectors.... "there are 2 very small balls inside it when you disassemble it, you may damage it, that's at least 1200 bucks for 6 injectors, etc..."
Andeson, you're great, thanks a lot for this VERY DETAILED video, I can't thank you enough!!!
I always get comments on my channel, that I speak and talk too much in detail, but you're my man, the truth is always in the small little details...
What's the worse thing? I have to buy new injectors. But I don't care. You just empowered me :-)
Now I don't even care if it gets broken, I'll try to do the same you did.
If it gets broken I'll buy a new set, but it is definitely worth a try.
Really Anderson, THANK YOU!!!!!!!
(TheMaxAcceleratrion)
Hello brotherx did you ever do it? how did it go?
Ale się na szukałem tego filmu super film.
awesome video mate
Thanks I need to clean mine very useful to know
Thanks for your posting video this is excellent video
awesome video.
thank you so much!
easy to understand explanation from your video..thank you
Yous did very good job explaining how to clean up and reuse injectors... any chance of polishing pin so it's a little harder for carbon to still too, also allowing it to move in and out more freely...
Thanks for sharing
Thats amazing! I wonder if its the same for all diesel injectors...
A very clear informative video.
Thank-you so much, very helpful.
The proper way to do it is to drop the injectors into an Ultrasonic bath of diesel and detergent for an hour or two (overnight for the really bad ones), give them a rinse and you should be ready to go.
do i need to disassemble injector when dropping it in bath?
I was waiting for that comment. In general yes it is the way to open them but a steel wire in the holes and a steel wire brush are a big no no....
Yes and you have to dismantle them when cleaning with a ultra sonic cleaner. As well use nitrile gloves and a lubricant when touching them. Sweaty fingers can course corrosion!
Great video thanks for sharing cheers from keith in New Zealand 😊
Nice work sir. Thanks for the informative video.
Wow. My volvo penta 2001t just wont start. I've tried everything. Flushing fuel system' filters everything. Im confirmed enough to try this now. What's the worst than can happen at this stage. Thank you so so much
Great video well repaired it should be better that new 🤘🇬🇧
Super clean job. Just wondering if he did test the injectors for correct opening pressure, spray pattern test, and leak test.
thank you for this video.
Good video thanks for taking time to make
Important valuable information thanku sir👍👍👍👍 really appreciate
That was awesome! Thank you
I saw your video,, I feel like can do same thing 😅,, I did (clean injectors) when I start the engine never working 😅,, recover with mechanic take €420 to retast and fix the injectors 😂
Thanks 👍
thnx mate good video, i just wonder how was your driving experience after cleaning all nozzels? and how many miles did you drive before u cleaned the nozzels ?
Very helpful. Thanks
Great video! Any advice on dealing with leaky injectors?
Very good... Thank you extremely helpful
Thanks for the tip on how to separate the injector, I didn't have a Scooby, but im an expert at prodding things into holes to open them up , hence the reason I've got 4 kids to 3 women lol
What dinomo metric you use??
Please tall me, thank!
Cool! I like fixing things if at all possible, if they have any life left in them.
Right now Im fixing a siezed up air compressor off a wheel barrow compressor.
The thing had sat for years tucked away in the shop and wasn't used because a hole had rusted into the bottom of one of the tanks. I fixed the hole with acetylene welding and cleaned out the fuel system to get the engine running again.
The twin cylinder compressor ran very strong and would do 160 psi with ease so I liked having it on my work trailer. It would actually run a 1 inch tire gun just enough to take a truck tire off.
The compressor was low on oil apparently which Id never thought to check and one day while running it on a 16 degree Farenheit day for just a few minutes before the compressor sadly locked up and came to a screeching halt.
It has set for 3 years now taken apart and I got the idea that I would file the gaulding off the crank and recondition the rods with a brake hone. And what do you know? I have it back together now with smooth working rods and crank.
I liked the compressor especially because I got it off the shelf and gave it life again. I gave it back its purpose. I made a place for it on my trailer. And I'm fixing to do it again.😎🙂
I know its 5 months later but why the hell would you do all that and nit change the oil.......
bunu yaptikdan sonra problem duzeldimi?
kendi aracimizin enjokterlerini boyle temizlesek problem olmaz demi.
kirlendigi zaman.
bilgisayara baglatip kod felan girmeye gerek varmi?
bazilari oyle diyorda.
Tesekurler
try a acetelyne torch tip cleaner will help you to clean those holes and also ACETONE is a cleaner i used for ever cleaning ac's etc . try it
thank you vary vary mach from iraq
Nice one 👍 Thanks for sharing.
Fab vid bro very helpfull
Thank's i fixed mine today
🖐️😀👌
Great job thanks
do all the pins come out of th nozzle i have a bosch injector and the pin wont come out car is a none start vauxhall astra 1.3cdti
With a name like Rockerfeller, I'm sure you could buy an injector factory.
Nicely done thanks
Put new videos and difference injectors.
Good for someone needs clean for self.
Big + for you.guys.
Great video
Nice ,good work
Is it good to add diesel addictive for injector cleaning? (Liqi moly super diesel addictive )
Great video. Just for info, you shouldn't continue past the first click on the torque wrench.
great video