How to grease a semi/ How to properly grease a semi-truck/ How often to grease a semi-truck/
ฝัง
- เผยแพร่เมื่อ 13 พ.ค. 2024
- New Shop Info: goo.gl/maps/HzwG98iioszjQWRP6
TAT Express Inc.
972-225-3017
4140 Langdon Rd.
Dallas TX 75241
How to grease a semi/ How to properly grease a semi-truck/ How often to grease a semi-truck/
truck maintenance,grease gun,semi truck,drive shaft,oil change,how to,slack adjuster,truck driver,semi truck maintenance,truck maintenance checklist,truck maintenance tips,truck maintenance hindi,How to grease a semi,How to properly grease a semi-truck,How often to grease a semi-truck,truck maintenance intervals,diesel truck maintenance,grease gun refill,how to grease a semi 5th wheel,how to properly grease a semi truck,how to grease a 18 wheeler
Now Hiring!
Here at TAT Express, we are always looking to work with highly motivated people and service specialists to join our dedicated and knowledgeable team.
CURRENT POSITIONS
Service Advisor/ Service Manager
tatexpressinc.com/service-adv...
Journeyman Technician
tatexpressinc.com/journeyman-...
Apprentice Technician
tatexpressinc.com/apprentice-...
DPF maintenance is a very important part of keeping semi-trucks running and operating as they should. In this video, I go over what is DPF maintenance and why it's important.
If this video has helped you in any way show your appreciation by buying me a coffee ☕️
Cash App:$tatexpress
If you have any questions feel free to reach out to us at
info@tatexpressinc.com
New Shop Info: goo.gl/maps/HzwG98iioszjQWRP6
TAT Express Inc.
972-225-3017
4140 Langdon Rd.
Dallas TX 75241
Join our Facebook group
/ 2517634715134383
Check us out on Facebook
/ tatexpressinc
~-~~-~~~-~~-~
Please watch: "Do Not Delete your Semi/ Do NOT delete your Semi/ Three Reasons Not to Delete your Semi/ DPF Deletes"
• Do Not Delete your Sem...
~-~~-~~~-~~-~
~-~~-~~~-~~-~
Please watch: "How to Replace A Wheel Seal on Semi/ Wheel Seal Leak/ Wheel Seal Installation/100kMiles Inspections"
• How to Replace A Wheel...
~-~~-~~~-~~-~
#semitrucks #semimaintenace#TATExpress #dieselengines - แนวปฏิบัติและการใช้ชีวิต
Reference king pins. I always Jack front end off ground, to relieve pressure. Turn tires left, by hand, grease, turn tires right, grease. Then work tires back and forth. Big difference in longevity.
I had a tech that would always advise drivers to change their kingpins when they wouldn't accept grease. I knew he was wrong when I found out that you should be lifting that wheel when greasing that kingpin like you advised.
It's never done that way in shops with pits.
That sounds goofy any shop set up properly for a pm is going to have a pit
This is kind of shop if would like to take my truck. Very knowledgeable people. Thanks for the video
🤣🤣🤣🤣 that's my truck. 🚚 you guys did excellent work on my king pins,U joints, rear brakes, tire rod and ends
It's not excellent work he says they may not take grease sometimes 😂 that's his sitty fitting and hes pumping away with nothing going inside and he says it's fine lol
@@ReputableRides-bb7wy that video is before they change everything out genius.....
Thanks for the vid! By far my favorite channel for truck maintenance, keep up the good work Adam!
I truly like how you explain everything 💯💪🏽🚚
Excellent video! (Because of the insight to preventive maintenance)
Brother you are a Big Help!!
Great video! 👍🏻
Have you ever tried an automatic lubrication system like the grease jockey by Graco?
These videos are so informative
Can you do a video on how to do a full service?
Appreciate you bro 👍🏻
Good job
What brand is your grease pump cart?
7:10 that's a great tip, simple but I never thought about that. I've had problems sliding the 5th wheel when loaded but easy to do when empty, this should help
@@youtubeisawesome2487 what do you recommend?
I would recommend lowering your landing gears, once they touch the ground lower your tractor bags, and proceed to unlock to move the 5th wheel, all the loaded pressure should be off and lot easier to move.
@@Hypnotikshiva thanks man, I'll try that next time I'm loaded heavy
Great video thanks
Glad you enjoyed it
Great informative video 💯
Thanks for watching, be sure to subscribe
looks to me that you need one of those locking grease ends for your gun. I love mine. Grease fittings actually take grease
Thanks 🙏🏻
You are welcome. Be sure to subscribe
do you do overhaul at this location?
At 11:24 in the video, you were greasing the front steer area and it is clear that the truck needs new front brake pads. They do not look like they are wearing correctly.
You saw call that?
I was taught to add grease until new grease is seen coming out on kingpins, slack adjusters, and any where else where it isn't sealed like a s cam.
Does an Automatic Trans have grease fittings like a manual?
Hey Adam, howdy from Northern Indiana
Working in the industry as a tire tech. Would love to see more content! Btw paccar could you show us how to use the priming tool? 😅 had a bad time yesterday one Just would not work
Glad you enjoy the content 👍🏼🔧
Do you ever grease 2012 Prostars
👍
My truck has leaf springs and drivshaft that is a completely sealed system, no grease fitting at all on the U-joints. Would you recommend having them installed?
Not at all! Non greasable Ujoints are higher quality, not only in longevity but also in strength. Look un Spicer non greasable UJoints
Can you show it on a semi trailer as well🤙
You should get a 10000psi greese tips the one you used doesn't seem to do the job...thx bros for the vids.
Greg B, appreciate the info
How service. Lng CNg semi truck
Question detroit masters, which transmission and rear end is best for the 14.0L and 12.7L?
Kemetnu King Trucking, I recommend following the sticker inside the door jam for the drive line setup. It is what the truck was manufactured with.
so we're supposed to grease the truck once every 10k miles? I grease it after every 3k miles, 2 pumps on the grease gun, is that bad for the bushings?
The more the better. You can break your monthly milage into an A and B service.
Do these things on the A and these things on the B. Keep a book with all replacement parts numbers, volumes and types of fluids will make future maintenance easier
❤️
Is there any particular kind of grease we should use or any grease would work. ?
Red high temp grease.
What would be the ideal psi for grease gun to grease a semi truck?
4500 psi
Forgot the leaf springs front and rear, also didn't take weight of king pins.... completely forgot the top of the King pin.... only greased the bottom incorrectly.
Other than that....not to bad !
Shouldn't you lift the weight off the king pin before you grease it ?
Yes!
Mr Adam ,my engine Detroit 60s 12.7
I notice my coolant temperature is 200-204 when am idle or in traffic
Is that normal , 180-185 cursing
Plz I need your advice , thank you
Pretty normal, you can add a switch to turn on the fan manually so you can turn it on while you're at idle
It will run that hot because lack of air flow a manual fan switch will change that
Separate air to air cooler and a/c condenser from radiator . Blow out with compressed air .
Make a video on your “creeper “
Grease the fifth wheel , raise the trailer slightly above the fifth wheel and back tractor stopping before coupling . Lower trailer and complete couple .
That's actually the proper way to connect a recently greased fifth wheel to a trailer. I also, lower my air bags to the fifth wheel (when the fifth wheel has been recently greased) and slowly back under the trailer (without having the fifth wheel touch the trailer) before coupling to the trailer (then I raise my air bags until the fifth wheel touches the trailer and then I back the tractor until it connects to the trailer without having any of the grease slide up to the top of the fifth wheel).
Owner may do that, but for a driver that may be too much work lol
Complimentary breakfast every Friday???? 😮😮😮
What about the leaf springs????
Some trucks have leaf springs with the grease zerks.
Some newer trucks I've noticed dont have them.
"I would recommend replacing your grease gun tip".... Or at least tighten it down if you can on that tip. Zerks aren't the problem if every single zerk isn't sealing with the gun tip.....
Thank you, because of this I watched a video on the tip that it can tighten or loosen. I don’t believe many people even know that. Wow I appreciate you leading me there
@@jacob2483 Glad I could help, bro. Also, remember that tips don't last forever. They wear out.
@@DamagedF0X many thanks, take care
LockNLube coupler saves the headache of having to hold the tip.
Thanks for sharing. 🔧👍🏼
Jack the front axle and get the weight off the king pins.
Great advice. This tutorial was mainly for drivers with no bottle jacks. Thanks for sharing.
انا مكنيكي شاحنات واريد ان اعمل لديكم
In my opinion. You should grease no differently than you would do PMs it all depends on Applications! OTR will get the longest intervals.But me personally I treat my truck As severe duty so regardless of my application which is Regional/Local/OFF-Road I grease Weekly, i PM Every 10,000 miles or Less. I Run Oil samples every time. I run Fuel Additives & Oil Additives. I could Push it longer but my truck is 8 years old with 750,000k so I don’t wait until things are bad before I service them. Like the old timers say “be good to her and she’ll be good to you” God Bless
10 k oil changes, that's insane....w today's synthetic oils....u can easily go to 50 k w oil sample!
Even higher w good oil filter changed at 50 k!
✌️
Don't 4get to grease the front leaf springs
I have 2 spring pins that refuse to take grease
Replace grease zerks . Hit spring roll with hammer . Air hammer with large flat punch may work best .Try letting weight off spring lift the frame .
That's actually incorrect Adam you see you have to drop your air bags when you get under your trailer with fresh Grease on the fifth wheel after your under then raise the airbags that should raise the fifth wheel on the trailer without it sliding any Grease off
😷🙂
💪🏼🔧👊🏼
*****🇺🇸🎼🎸🎤TAT Express 🤗U hit right onT target 👍🏻 allT extra grease onT side will just build dirt on N if they don’t get grease 🤔it’ll burn them from drying N’ll cause damage 😢is better 2 check N grease them 👍🏻 Tks TAT Express U save extra 💲 onR pocket 😇🥁🎹🎶🇺🇸*****
You are absolutely wrong about pumping grease into it until it comes out. That is called over greasing. That is how you blow seals out. You guys put a lot of great content out but this one starts out wrong right in the beginning
Which ones have seals? Ive never noticed any seals on ujoints and slack adjusters. Only been greasing my truck for 2 years so honest question.
The seals on your slack, tie rods, drag link, u-joints s-cams and every other place you put grease to it. You shouldn’t over grease cause then that causes grim and dirt to accumulate around those joints causing premature wear on those components.
@@PSALM-144-1 oh yeah! All those seals are already busted on mine im used to seeing them ooze a little. But thats right after i replace them dont want to balloon those again!
people say when u grease the front end its good to jack the truck up is there any truth to that?