What a great informative video thanks.I have the same issue with my 2015 Nav poor starting and a P0380 error. I'm going to replace both the controller and the plugs as its now got 140K on the clock
there are not enough words to thank you . it was really awesome and i have the same issue now i am very confidant to solve the issue because i don't have the wiring diagram at that time.
Wow great walk through for sure! Well done keeping the camera on your other hand for the whole video! Precious info there, +replying here! Going to investigate a P0380 error on my 2012 Pathfinder tomorrow. Cheers from France :p
Great video with a lot of info... I've had this done a few months ago, then the problems started again, had the glow plug relay changed a second time... Then the next morning with a frost it wouldn't start at all... Is that the glow plugs themselves or a faulty fitting on the relay?
Excellent walk through, thank you! Planning to follow your steps this week to investigate a P0380 error on my 2012 Navara. One question though, which ports on the glow relay were your oscilloscope in when you were testing continuity on ECU terminals 131 and 137? Obviously I can't actually do the ECU signal test as I don't have an oscilloscope, but I'd like to check the wiring anyway. Cheers.
i have only 7-8v on each plug - plug no4 - 0v - the engine start but the engine it does not hold idle, when the temperature of water start to heat it's ok
Hi, currently having the same issue however when i check the 4 pin plug there is power going through it, for the first second ignition is on it's a bright glow and then light is reduced, any ideas? I've replaced plugs this morning to no avail
Did you know other solution for p0380 nissan d40 I check all the circuit change relay and 4 glow, erased code, bud still como back the check p0380..... Car don, t lose power...
What a great informative video thanks.I have the same issue with my 2015 Nav poor starting and a P0380 error. I'm going to replace both the controller and the plugs as its now got 140K on the clock
Your a hero!!
Been chasing problem for 6 months. Good simplified explanation. With thanks
thank you very much. excellent lesson. greetings from Prague
there are not enough words to thank you . it was really awesome and i have the same issue now i am very confidant to solve the issue because i don't have the wiring diagram at that time.
Seriously good video, wish we had more lads like you in the trade trying to help one another👍🏻
Wow great walk through for sure! Well done keeping the camera on your other hand for the whole video! Precious info there, +replying here! Going to investigate a P0380 error on my 2012 Pathfinder tomorrow. Cheers from France :p
C’était quoi ton problème du coup ? Je le même soucis
Great video, well explained
Great video just working on one at the moment that doesn't have any 12v coming from engine ecu on control wires
Nice bit of work Sherlock!
🎉🎉🎉thank you very much ❤❤❤
Quality content as always.
Very thorough diagnosis
Great work buddy
The red channel that had 12v was it 12v after the new glow plug module was fitted good video
Nice technical educational video
Thanks very helpful, Well worth a like.
Great video with a lot of info... I've had this done a few months ago, then the problems started again, had the glow plug relay changed a second time... Then the next morning with a frost it wouldn't start at all... Is that the glow plugs themselves or a faulty fitting on the relay?
Instablaster
Excellent work very educative
Excellent walk through, thank you! Planning to follow your steps this week to investigate a P0380 error on my 2012 Navara. One question though, which ports on the glow relay were your oscilloscope in when you were testing continuity on ECU terminals 131 and 137? Obviously I can't actually do the ECU signal test as I don't have an oscilloscope, but I'd like to check the wiring anyway. Cheers.
Did you manage too fix ypur fault
Good work, thanks for Shаring.
i have only 7-8v on each plug - plug no4 - 0v - the engine start but the engine it does not hold idle, when the temperature of water start to heat it's ok
Keep em coming
Where is the heater control module I can't locate it on my nissan navara I've looked by the battery can't seem to see it
Is there not two glow plug relays?
Nice work. 👍🏻
Thanks for the Video 🫶🤙
Hi, currently having the same issue however when i check the 4 pin plug there is power going through it, for the first second ignition is on it's a bright glow and then light is reduced, any ideas? I've replaced plugs this morning to no avail
Seria genial que lo tradujeran o subtitularan al español pero aun asi se entiende Gracias por el video bendiciones desde PERU.
Can you please share the wiring diagram 🙏
Did you know other solution for p0380 nissan d40 I check all the circuit change relay and 4 glow, erased code, bud still como back the check p0380..... Car don, t lose power...
Im from Chile, saludos.
Check the resistance from the 4 pin plug behind battery to ground, one of your plugs may have a bad wire/connection
@@intelligentauto737 you are a my jedi máster, green wire was the truble, thank for share your knowledge, saludos desde chile.
@@rodrigoelboli cual cable verde ?? El que va a una de las bujias o el que viene de la ecu??
@@rodrigoelboli .. Hi! My Navara has the same problem. What did you do to fix the green wire? Thanks..
where you based ..
Gateshead, Tyne & Wear