ROSS RACING GEN 1 B58 PCV DELETE KIT | DIY and Review
ฝัง
- เผยแพร่เมื่อ 19 ก.ค. 2024
- Today I show you how to instal the Ross Racing Performance PCV Cap and Oil Catch Can Kit and give you my thoughts and updates on this kit from a 6 month user!
Chapters:
00:00 Introduction
00:53 Overview
01:45 Engine Bay Prep
02:05 Remove Strut Tower Bolts
02:36 Oil Catch Can Setup
04:09 Oil Catch Can Installation
05:19 PCV Delete Cap Overview and Prep
06:13 Remove OEM PCV Cap
06:59 PCV Delete Cap Installation
08:12 AN Line Installation
10:13 Showcase and Final Thoughts
12:25 Recommendation
13:09 Outro
-----------------
FEATURED:
ROSS RACING PCV DELETE KIT: tinyurl.com/2stsz7s6
-----------------
MERCH: noclutchgarage.com/merch
ALL MY MODS & LINKS: noclutchgarage.com/mods-links
-----------------
SPONSORS:
EuroMpire
-Web: www.eurompire.com/
-Instagram: @eurompire_official
MST Performance
-Web: www.mst-performance.com
-Instagram: @mstperformance
P3 Gauges
-Web: www.p3cars.com
-Instagram: @p3gauges
MarinTuned:
Web: www.marintuned.com
Instagram: @marintuned
-----------------
DONATIONS WELCOME
*Any donation made is completely voluntary. All proceeds directly affect the development of the channel*
PayPal.me/noclutchgarage
Cash app: $NoClutchGarage
------------------------------------
RECORDING GEAR:
Sony a6400: amzn.to/3EMapad
iPhone 12 Pro: amzn.to/3cQmmPd
GoPro Hero 7 Black: amzn.to/2HjPuQn
Zhiyun Smooth-Q Gimbal: amzn.to/2PHhRNB
16-Inch MacBook Pro: amzn.to/32MBFnl
-----------------
FOLLOW ME ON SOCIAL MEDIA!
Facebook: / noclutchgarage
Instagram: tinyurl.com/y25p4b6g
TikTok: vm.tiktok.com/ax56pE/
TH-cam: / noclutchgarage
-----------------
*All music used under license by Epidemic Sound
*All video content is original content by NoClutch Garage
* Some links may be paid links. A small commission is made when using such links; all proceeds help support the channel development* - ยานยนต์และพาหนะ
When putting my kit on I was torquing the bolts to the 56nm had the torque wrench set to 41.3 ft-lb and 2/3 bolts snapped right in the middle same spot in both
That’s crazy. I’ve had mine snap too but that’s usually because they were weakened from stress if they were over-tightened before.
@@NoClutchGarageI found out it’s because if you have the m8 bolts it’s only 30nm not the 56 but if you have the m10 it’s 56
ah, that’s crazy I’ve never seen the M8s use there before!
Also, always replace stretch bolts once removed.
Hi LJ , at 9:55 you push the braided hose elbow into the manifold. My stock setup has a heat shielded breather hose from that manifold down to turbo inlet pipe. What should I do with that stock breather hose? Thanks
You meant to say the Valve Cover. Yeah so this kit effectively forces you to delete that system. There are a few ways you can go about it.
1. You can delete the line altogether and via custom tune you can have the code that will trigger when the heater attached at the end of that hose is unplugged removed, and that will be the end of that. Then you will need to plug the intake pipe where the hose used to plug into with a heavy duty rubber cap and a clamp.
2. You can remove the hose only and leave that end piece (heater) plugged in and supported somehow (I have done this temporarily, so I know it works) and then cap your intake pipe with a rubber cap and clamp.
In either case you either need to plug that inlet or get another inlet that deletes that hole altogether. At the moment I have deleted the system altogether and I don’t have to bother with any of it.
@@NoClutchGarage thank you , I just realised the kit has a silicon plug to cap the oem hose, held in by vacuum but feels a bit loose. I think I’ll remove the hose and cap it somehow down at the turbo intake pipe
@747Richie Those work but they will wear over time sometimes. If you message me on instagram I can send you a link for a better one you can use!
when you add the catch can , is it normal for it to smoke a little bit out of the top of the catch can?
Yes, it’s venting.
What about the other end of the breather hose? What do I do with the OEM one?
Plug it.
Do you know if there is a PCV delete kit for an N55 engine?
Yes, Ross Racing makes one
@@NoClutchGaragetop video merci ...est il possible de le supprimer electroniquement avec un reprogramateur ?
Would this still fit with a top mount turbo?
This particular configuration is specidic to BigBoost kits, other configurations can accomodate top mount turbo kits
do they nopt make it anymore? all i see is the breather kit for 500 bucks lol
This is the breather kit