Six incredible 3D printed projects for fun and discovery
ฝัง
- เผยแพร่เมื่อ 15 พ.ค. 2024
- Check out my 2nd channel, TT Racing: / @ttracingyt
3D printings are becoming easier to use and capable of better results, so why not use them to create amazing projects. In this video, I showcase six hand selected projects primarily made with a 3D printer. I advise on how hard they are to print, assembly difficulty, hardware required and educational value.
All of these projects were worthwhile and satisfying, so thank you to the creators who released them free of charge. Also, a big thanks to my kids for their help, especially my daughter, who has all the hallmarks of a budding maker.
0:00 Introduction
1:01 Balance game by janlegaard
Thingiverse: www.thingiverse.com/thing:633...
2:38 Mobile Exo-Suit by Jajaum3d
Printables: www.printables.com/en/model/5...
4:23 Dummy 13 by soozafone
Printables: www.printables.com/model/5931...
Assembly video: • Dummy 13 Assembly Guide
Lucky 13 butt remix by Pedro Lopes: www.printables.com/model/3501...
7:07 Toroidal Launcher by Brent Peterson
Makerworld: makerworld.com/en/models/9338...
9:08 Animatronic puppet face by James Bruton
TH-cam: • How To Make Robots Mov...
Face GitHub: github.com/XRobots/ServoSmoot...
Remote GitHub: github.com/XRobots/openDogV3
3 axis joysticks (Aus): core-electronics.com.au/3-axi...
Arduino Uno shield: www.jaycar.com.au/duinotech-a...
My remixed controller part, prepared 3MF and Arduino code: www.printables.com/model/7171...
14:01 Hand crank generator by Tom Stanton
TH-cam: • Building a Generator
Printables: www.printables.com/model/6581...
Serpentine stator remix: www.printables.com/model/7122...
My remixed winder part: www.printables.com/model/7172...
0.63mm enamelled wire: www.jaycar.com.au/0-63mm-enam...
19:33 Conclusion
Buy quality and affordable filament from X3D. Buy 3, get 1 free and a free sample pack with every order: www.x3d.com.au
Get Quality Resins from 3D Printers Online. 5% off storewide for Teaching Tech subscribers [Code: tech5]
3dprintersonline.com.au/
Take a look around and if you like what you see, please subscribe.
Support me on Patreon: / teachingtech
The last two - but especially James Bruxton's, in my opinion - are also teaching some very valuable core skills: general problem solving and extrapolating from incomplete instructions. These skills might be so fundemental to you that you didn't even realise it, but anyone who sets out to recreate any of James' projects is going to have to fill in some blanks for themselves. That's not meant as a criticism, but rather to highlight how those projects can be very useful for developing skills a person will use every day at work or school.
As a person who doesn't like step by step instructions I'm going to have to do a couple of projects just for fun.
I like videos like these that show case new prints. I would like to see 3d printing youtubers feature a new thing to print at the end of their videos
These are incredible. The increasing complexity means there is something for different maker levels. Thank you for sharing these.
I really liked how you broke down each project. I would love this to become a series of yours - I'd watch another hundred!
Yep! If there's another video in this series, I'll watch it as soon as it comes out
You’ve got my vote
I've had a few 3D printed projects like this over the years, just not structured like this. I will make a playlist and there will definitely be more 3D printed projects in the future.
Those figurines are great for stop motion animations!
Made Lucky 13 for my son before Christmas. He loves it and like your daughter we took turns posing him, me before work, my son before bed. Great little game we have going.
great suggestions! Thank you
We have been making rust repair panels with 3d scanner, 3d printer, and shop press. Easiest way to restore a rusty body panel.
Michael you are an inspiration and your videos always end up on my saved Playlist. (Also a BIG thank you for your work talking to Bambulab about custom firmware - another example of how much you do and care for our community)😊
Well put I completely agree, thanks Michael!
Kudos for the Ayrton Senna shirt
Don't think I've seen that shirt before, love it!
Can't wait for your next TT racing vid!
Those photos of Dummy 13 flirting with Exo-suit :D you made my day!
Great video as always. Keep up the good, fun and educational work.
More videos like this. Projects that are good for education.
This is some great content, seconded.
Great video, love the eyeballs!
I love the *13 models. I printed one at 250% in PETG, stands about 18" tall.
Hans Maximus Julian Moleman! I LOVE it!
The poses were the best part of the video - what a good game!
Nice presentation. The Toroidal Launcher seems to be the most practical to illustrate mechanics and mechanisms that can be created with 3D printers. The next level would be to teach how to design the parts with a CAD software.
Thanks for showing off Dummy 13! Or Hans, I should say…
Good video! Thank you!
Best name for a figurine EVER!
thanks for sharing.
have a nice day.
Greetings from the Galilee.
Thanks for the Video
Have printed quite a few the DUMMY 13s as stocking stuffers for my nephews, they loved them. Printed a 250% one for myself!
These are some great projects, and the last two definitely got complicated pretty quick but in a good way. I was a little sad to see that you did not call out electroboom during the full bridge rectifier. 🤪
I have four Dummy 13s, including a silver knight and a black knight. I recommend the knight skin/armour. Its brilliant.
I made the toroidal launcher with my son a little while back. To make it easier for him to launch I made the bottom grip longer and a longer top shaft to improve hand clearance.
I'm struggling with this. What filament did you use, my dimensional accuracy is not good.
@@stevenborg2477 just a inland black pla, my fit with the triangular part in the bottom wasn't good, so I had to make it a little bigger with a Dremel. Then lube is also pretty essential, the first little bit it took a lot of torque to get it spinning.
Dummy 13 at 250% is awesome! Add the lamp mode remix and it makes the coolest desk lamp ever!
I think the electricity generator with tyroidal planetary gearset would be right up your alley michael.😮
very good ideas!
You should add a few capacitors to that hand crank. That way, the power doesn't fluctuate that much and you will have a better experience with your emergency charger (Li-Ion batteries prefer constant voltage and constant current).
I only mentioned it briefly but I did include some as per the original build instructions. I found the measured voltage was significant higher after adding them. I figured the fluctuations were like PWM without them.
I see MP4/4, I upvote :)
My biggest claim to fame ever was driving four laps in that car at Interlagos in 2003.
That sounds amazing :)
The eyes are really cool i want to try that
Awesome projects. But the shirt was tops
Nice Video, Subbed!
Great video. it would be greatly appreciated if you could have a wiring diagram for the joysticks to your uno. Thank you
@TeachingTech Regarding the poseable figure, you mentioned using PET-G or ABS. Just curious if you have tried PLA+ (PLA Pro) which is more resilient and durable for mechanical items like this? 🤔
Ive used Sunlu PLA+ only yesterday and its fine. The trick with Dummy13 is you MUST calibrate e steps and flow and use the Outer/Inner option under wall settings. These things are key for precision prints and this just wont fit without them. Just about the print the Deadpool accesory kit.
You should try to feed the generator with some eletricity and see how it would perform as a motor
Loved the projects, really looking forward to doing the hand crank charger
Also I was curious if you've considered doing a 3dsets rc model on the channel? They just released an awesome s30 Z model that would probably be up your alley
Never heard of it but I'll look into it.
Wow! Incredible. Thanks for the suggestion.
The Exo Suit could go so far.
Application, liitle mini-servos, usbc connection, camera & flir sights, AUTONOMOUS HOME SECURITY
I'm pretty sure I know where you'll end up once you double the potential for posing.
When I'm bored I walk around the house and look for things that annoy me that can be improved with 3D printing and I start a little project out of it.
Could the generator be mated with a wind vane or it is not possible.
What is or how do you achieve that triangular forged carbon look on the top of your remote? 12:18 Man so cool.
There's a female lucky 13 that's got a cute heart torso that I love.
Hahaha -- I think you need a treadle or pedal version of the generator so that you can do something useful with your hands while generating with your feet!
I'm interesting in adapting a gravity 'driver'. Wind up cord, let it fall very slowly, geared to spin the generator fast.
@@TeachingTech From a few quick calculations, such energy quantity would be almost negligible, unless your object is absolutely massive. You'd need a mass of about 1 ton dropped from condsiderable height to outperform handcranking for 1 hour in terms of watt hours produced, but it would be interesting to see nonetheless.
Somebody likes Ayrton Senna! Awesome videos, BTW!
8:05 For the most material combinations that include plastic, silicone oil, or silicone grease (most time better if you can bring it in) will be the lubricant of choice. Normal oil is not good in lubing plastic. Sometimes it make it even worse. Every material combination has its own lubricants. For example wood. Try to use oil on wood. It will be much worse than without and it will start squeaking. For wood, hard wax is the way to go.
Those joysticks where seriously 60bucks!
Very nice video. Quick question - do you happen to know which grade of magnets you used for the hand crank generator? I have been planning to build it, and I was just wondering which grade of magnets were used to get the voltages you measured since I am not planning on putting all 8 coils in series like you did, and I want to make sure I will still get a sufficient voltage. Thanks in advance!
They were man to be N52 as recommended by Tom, however they were cheap eBay ones rather than from a reputable magnet supplier. I have no way of measuring the strength, but I know the dimensions were off compared to Tom's video. Mine needed to be glued in whereas Tom's were a nice press fit.
@@TeachingTech Got it. Hopefully if I get n48 magnets, I will have better results with fewer coils in series. We will see... Thank you for your help!
@@TeachingTechhow come you stopped uploading to the tt racing channel? Would love to see some more videos! Thanks!
@@nathanholy Just a matter of progressing far enough to have something for the next video. I will get there, don't worry (but please be patient).
Given the small sizes, Have you tried Dummy 13 in RESIN ?
Attach the planetary gears from the launcher to the generator, and you don't have to turn it as much or as fast.
Hey what happened to the tt racing channel that was so cool
Hand crank your way to post apocalyptic mod-cons.
Good video
Plastics should be lubricated with silicone and not oil 😉
what filament is that you are using? the one that is sort of gun metal grey? looks amazing
It is eryone PLA. I got it from x3d.com.au but it appears they no longer stock it.
Found the spool, 'Rainbow Lagoon' if you are searching for it elsewhere.
How could anyone click thumbs down for your videos?! What is there not to like?!
hello, I've seen in this vidéo and the previous one that you have an strange bed on your bambulab,
where did you have purchae it ? and is it real carbon ?
Thank you verry much for your work
have a nice day
PEO patterned bed on Aliexpress: s.click.aliexpress.com/e/_DCTHuU1
At 10:27, how did you split this into several parts? Is this a Bambu slicer feature or is this available in stock PrusaSlicer too?
This is afeature in Bambu Studio/OrcaSlicer that I hope it ported back to PrusaSlicer. It's excellent for prints like this to organise everything.
I plan to make to animatronic eyes!
Are there any tt racing videos coming?
What build surface are you using to get that finish?
It's either PET or PEO. There's also PEY that can leave a really cool hologram look!
PEO patterned bed on Aliexpress: s.click.aliexpress.com/e/_DCTHuU1
What is the link to Moleman's dedicated YT channel?
The Dummy 13 frame can be printed with PLA+/PLA Tough but from what I've seen it gets worn down fast, not as fast as norm PLA but PETG would be better
I've printed lucky 13 parts(did a ninja turtle one) in Pla but admittedly I never read the instructions
No (Michael) Afton robotics jokes in the comments? But seriously, that's probably the one print that most interests me in this video.
Give your kids phones but they can only use what they can charge. Your kids will have massive arms by the time they hit college!
6:00 "Haaans" ((Germans everywhere in shambles))
Could you block the MckenzieBumba account?