Do the Nibbis come with a choke lever on them? I want to order myself the 28mm but I wanna make sure it has a choke for those cold winter day starts. Does yours have a choke?
Nice video but you should of got a 26mm, nibbi carbs are beautiful I have the 26mm red an black nibbi. An the nibbi has an air screw because it's on the front half of the carb, if it was on the engine side of the carb like your GPS carb or all the other chikuni carb then it's a fuel screw. Imo I love the air screws like the nibbi an all flatslide carbs have, way easier to tune brotha, but nice video homie keep killin it!!!🤘🏽🤘🏽🤘🏽🤘🏽😎
Yeah tbh I like the air screw better! I was also thinking about going bigger but bigger isn’t always better and with the 22 I’m still hitting 65mph all day long! Much appreciated!
What throttle cable did you by I bought the whole 28mm nibbi carb kit and the first 70in cable ripped and bought another one and ripped again idk if it’s too short or I’m putting it wrong what cable did you use?
I was doing 65 with the gps aftermarket mikuni 22 I just swapped the same nibbi you have but im waiting for my chain so I haven’t been able to ride it did you increase top end speed?
I have road it! It runs pretty well I didn’t really notice much of a difference though cause it’s the same size as I had on before. Still pushes 65 all day though
what throttle cable did you purchase? the part that goes inside the carb isn't long enough on the one i purchased. i tried to modify it but you can't its wrapped in metal under the black casing. tried to unravel but its not working. ill just buy another
Here’s a link to one that I have this one comes with the cable www.amazon.com/Throttle-Motorcycle-Aluminum-Twister-Accessories/dp/B0BFDHJK6Z/ref=mp_s_a_1_5_sspa?crid=9FFYLXKEFSBM&dib=eyJ2IjoiMSJ9.LuFzuMdnNmiHV6gifQukUcn6-78h3o2u10DWkqdZ6_d4NRJ_QkcJeuvDIbRefkANY7wAvv0Hjwr5066FiqjgRaiZUH2fAncDX0-kyOiw38ihtdD5a2DjVb0K734IjPgBYj3CONSxqrMLwZzRf0giZUROjufA1FmFX61xhCsXeBvkD6XpDe-2YSrhF-wxn1_N2DMH-wIzQaFK9gKTpR_Gag.7I3FmheIA3w1YztwfqfA-Y0TfozjySZpKsWO_NOxH50&dib_tag=se&keywords=quick+twist+throttle&qid=1713497188&sprefix=quick+twist+th%2Caps%2C184&sr=8-5-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9waG9uZV9zZWFyY2hfbXRm&psc=1
The brake mount for the hydro? I wouldn’t know the measurements off the top of my head but it will be completely different for different brake calipers
@@Guido19 well, I bought the Minibike Hydraulic Brake System from go Powersports and didn’t look through it good enough, and didn’t see that you need a different bracket for the brakes so I would appreciate a lot if you measured it and send it because I really am not spending $50 on a piece of metal
@@nigelleoldfield8514 well I’m not able to grab measurements but this is as good as I can do. Here it is for sale for $10 on gopowersports www.gopowersports.com/mini-bike-hydraulic-brake-caliper-bracket/?campaignid=15361704457&adgroupid=&adid=&gad_source=1&gclid=Cj0KCQjwn7mwBhCiARIsAGoxjaL6nMnv0twPpzwlfdwF_ZwULZjeki1UqWcLeK86mLXj2M6sLJccm4gaAjdtEALw_wcB
Make sure to like and subscribe!!! Stay tuned!!
Been standing by nibbi since the beginning off my mini bike adventures so about 5 years now
I love how you went into specific details appreciate you can’t wait to finish setting mine up Saturday
Keep up the great work bro!
Thank you!!!
Could you please show us how to tune it? Like fuel mixture screw, main jet, pilot jet, throttle needle etc. thanks
That might be a future video!
Dope video bro . I got two different builds at the moment
A built 212 going around 48-50mph &
A Honda 200 torque setup going 45mph for trails
Heck yeah that’s awesome man!
Is this on the monster motor 80 frame
Yup!🤝🏻
hey nice build man! i was wondering where you got that little air filter for the tank? thanks
I got it at the local auto store!
Hey can you link me your filters for your valves and gas tank?
What do you do if your throttle cable doesn't have a tip?
@@samuelbrooks8199 you might have to buy a new one or you can solder a new end on
do i have to take the gov off when i put a better carb on
@@ashmatthews9122 usually yes. The aftermarket mikuni carbs you would have to get rid of it
@ yeah i jus got my nibbi carb nd don’t wanna install yet because of the gov thanks👍🏻
Do the Nibbis come with a choke lever on them? I want to order myself the 28mm but I wanna make sure it has a choke for those cold winter day starts. Does yours have a choke?
Yes they do.
Nice video but you should of got a 26mm, nibbi carbs are beautiful I have the 26mm red an black nibbi. An the nibbi has an air screw because it's on the front half of the carb, if it was on the engine side of the carb like your GPS carb or all the other chikuni carb then it's a fuel screw. Imo I love the air screws like the nibbi an all flatslide carbs have, way easier to tune brotha, but nice video homie keep killin it!!!🤘🏽🤘🏽🤘🏽🤘🏽😎
Yeah tbh I like the air screw better! I was also thinking about going bigger but bigger isn’t always better and with the 22 I’m still hitting 65mph all day long! Much appreciated!
What's the best jets for a 212 with the carb your talking about ?
@@Guido19what jets u running
What is on the rear left side?
@@samuelbrooks8199 it’s a oil catch can?
Could you tell me what pilot jet you installed?
@@stevenkudrna9463 I think I used the stock pilot jet
Hey where did u get The filter for the gas tank?
@@bozebohz8297 I got it at autozone!
What throttle cable did you by I bought the whole 28mm nibbi carb kit and the first 70in cable ripped and bought another one and ripped again idk if it’s too short or I’m putting it wrong what cable did you use?
hmm it depends on the minibike but it might have been a cheap cable if it just ripped.
I was doing 65 with the gps aftermarket mikuni 22 I just swapped the same nibbi you have but im waiting for my chain so I haven’t been able to ride it did you increase top end speed?
I have road it! It runs pretty well I didn’t really notice much of a difference though cause it’s the same size as I had on before. Still pushes 65 all day though
What jets are yall running
@@tgndeath3ater832 I belive it’s a 120
what throttle cable did you purchase? the part that goes inside the carb isn't long enough on the one i purchased. i tried to modify it but you can't its wrapped in metal under the black casing. tried to unravel but its not working. ill just buy another
can you provide a link too. i dont want to purchase the incorrect cable again
Here’s a link to one that I have this one comes with the cable www.amazon.com/Throttle-Motorcycle-Aluminum-Twister-Accessories/dp/B0BFDHJK6Z/ref=mp_s_a_1_5_sspa?crid=9FFYLXKEFSBM&dib=eyJ2IjoiMSJ9.LuFzuMdnNmiHV6gifQukUcn6-78h3o2u10DWkqdZ6_d4NRJ_QkcJeuvDIbRefkANY7wAvv0Hjwr5066FiqjgRaiZUH2fAncDX0-kyOiw38ihtdD5a2DjVb0K734IjPgBYj3CONSxqrMLwZzRf0giZUROjufA1FmFX61xhCsXeBvkD6XpDe-2YSrhF-wxn1_N2DMH-wIzQaFK9gKTpR_Gag.7I3FmheIA3w1YztwfqfA-Y0TfozjySZpKsWO_NOxH50&dib_tag=se&keywords=quick+twist+throttle&qid=1713497188&sprefix=quick+twist+th%2Caps%2C184&sr=8-5-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9waG9uZV9zZWFyY2hfbXRm&psc=1
Where did you get the seat from??
I got it custom made
Did you change the jets?
@@MikeBeatzcom yes I put a 120 main jet in
@@Guido19and the pilot jet
what size air filter do you need for the carb?
You will need a 46mm filter but it should come with one!
Did you have to change the pilot jet and main jet?
Yes I did and I adjusted the air fuel mix too
@@Guido19 what size jets did you replace them with?
@@brandongoutdoors I think I did a 110 or a 115 main
@@Guido19 Alr thanks
@@Guido19did u put more air into it
We’re do you get your street tires bro
gopowersports
What is your parts list for your 212 and what is your gear ratio? Thanks
I have the stage 5 kit pretty much. It’s all built up on the stock stroke and bore.
It’s around a 4.4 gear ratio
Bro when I tell you this bike so hard 🔥 you tripped how fast do it run if you don’t mind me asking
Appreciated!!! I max out at about 65mph
Can you drop a link for the carb please!! Great channel keep them coming
www.amazon.com/Carburetor-110cc-130cc-Motorcycle-KAWASAKI-Scooter/dp/B0B4VTD3JT/ref=asc_df_B0B4VTD3JT/?tag=hyprod-20&linkCode=df0&hvadid=647287755296&hvpos=&hvnetw=g&hvrand=14561118343802759076&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9030236&hvtargid=pla-1967379290856&psc=1&mcid=a79ced95f3f330b68534340ff55aad4e
Did you delete governor or still have it in ? Please Lmk , thank you
@@luisperez8995 I removed it!
Did you mod the frame like that to fit the mikuni carb?
Yeah I had to even with the stock carb for clearance
@@Guido19 Alright thanks
Hey bro, remember your old video of the break mount can you send me the measurements of it cause I don’t want to spend $50 for amount
The brake mount for the hydro? I wouldn’t know the measurements off the top of my head but it will be completely different for different brake calipers
@@Guido19 well, I bought the Minibike Hydraulic Brake System from go Powersports and didn’t look through it good enough, and didn’t see that you need a different bracket for the brakes so I would appreciate a lot if you measured it and send it because I really am not spending $50 on a piece of metal
@@nigelleoldfield8514 well I’m not able to grab measurements but this is as good as I can do. Here it is for sale for $10 on gopowersports www.gopowersports.com/mini-bike-hydraulic-brake-caliper-bracket/?campaignid=15361704457&adgroupid=&adid=&gad_source=1&gclid=Cj0KCQjwn7mwBhCiARIsAGoxjaL6nMnv0twPpzwlfdwF_ZwULZjeki1UqWcLeK86mLXj2M6sLJccm4gaAjdtEALw_wcB
@@Guido19 yeah OK thanks man for your advice
I’m about to order one I absolutely hate my vm22 they are trash