*Came in today and my friend and I both rode **Latest.Bike** Scooter around for about an hour. Was lots of fun and didn't drain the battery much at all!*
thank you AJ and VOROMOTORS! this video helped me fix so many loose bolts that were on my refurbished model. i was worried i was going to have to do a full stem replacement. little did i know i just had to get to the 2 bolts behind the rubber guard :) Good ol me just overthinking every little lose part.
Just finished tightening the stem neck and I have to get under the front wheel. Well it’s not easy time consuming for the first time. Added note take phots or video before removing anything, because putting it back for the first time will be annoying. 4pm to 8 pm that’s how long it took me and younger sister. 😂. I was smart I had help. Putting the brakes back will be the challenge.
Got my Cruiser yesterday so far I’m loving it! Although the front wheel and tbar aren’t aligned. Tried forcing it to align with the lever (height adjustment) loosen but it won’t barge. Please help!
I purchased my emove Christmas 2023, it's been 6 months and I've used it a handful of times and it no longer charges. Tried everything, how can a charger go bad after 6 months? Very disappointed! Looks like this is not an isolated issue.
at 4:32 do not tighten these screws! They will break off and you will have to buy a new stem $190. At first you might think this is an easy fix pull the cables through replace stem and once again pull cable back up. The cable does not fit thought the stem. You have to open up the controller compartment an unhook 3 clips and pull the clips off. The clips are to big to pull through the stem hole. Once you rerun your cable you have to reattached the clips hot glue them and clip them back to their counter parts coming from the controller. You also have to pull you break lines out as well. th-cam.com/video/XNcUPPO2mbw/w-d-xo.html How to replace your main line on your emove cruiser
One tip for setting full hydraulic brakes is to loosen the caliper mounting bolts and then squeeze the brake lever. With the brake lever held, re-tighten the mounting bolts. This *should* center the caliper on the rotor.
This is how to do all tutorials only problem is, how to remove the front fender to get to those stem bolts, lol. If things get too difficult, it won't be done lol.
I hear there are some issues with the rear fender becoming loose. Anyone experienced this? Drove me crazy on the Apollo Explore. I was tightening the screws after every ride.
Hi, There has not been a reported issue with our rear fender. If you have any further questions, please do not hesitate to email support@voromotors.com or call us at 3237097329 Hope this is helpful!
100%. What happened to me..had to keep tightening EVERY RIDE. The screws didn't even grip and it fell off mid ride...almost ate the concrete during it. Very much a bummer situation 😭😭
My brakes make some weird noises. They move freely when I have the wheels off the ground so now brake rub. Also my bars have meat on them. What the hell could it be?
On those XTech's there's also a tiny Allen screw that adjusts the piston pressure that's not mentioned here. I was doing all the adjustments via tightening the cables at the three points but this other screw that's not mentioned adjusts the pre-pressure and THAT is what I've been told you adjust as the pads wear in, not the cables. If it'll let me share this link, I've pointed at the screw I'm talking about: i.imgur.com/5DugQt0.jpg
Hey dudes, regarding adjusting the brakes I saw you did 3 different adjustments for tightening them. Both of my brake levers are very loose and i can pull them almost full range before i feel the brakes kicking in. Which method do I do... First? Second? Third? Thanks!
@@VoroMotors you did! Thank you very much! I have multiple social media personalities...this is not my main... Was blanketing for help... You guys are awesome!🙏🏼🙏🏼🙏🏼
Hi...i have an emove touring scooter....after 4 days, of use, the front tire went flat....no puncture, looks like the inner tube just popped / failed. Voro gang - can you guys please post a video that shows how to take off front tire of Emove Touring, and replace the inside inflatable ture? help! thank you.
Rain reviews - very false information. few rides in rain and mine died after 3 months of riding. their warranty doesnt cover anything water related. i even purchased 2 extra years warranty and now voided.... I need to pay for following battery $490 controller $50 motor $295 throttle $42 walt meter $45 plus i need to pay $37.50 at the shop for inspection plus labor time $.
i hope you're a actor and not a mechanic at 8.10 minutes you just unlock the adjustment lock nut hope no one gets in a crash because adjustments screw went in and no more breaks,sorry but that lame,🤕😱.put a real mechanic,or analyze the content let's say i go 17mph hey i miss the stop by only 4 feet BANG I'M DEAD.
*Came in today and my friend and I both rode **Latest.Bike** Scooter around for about an hour. Was lots of fun and didn't drain the battery much at all!*
thank you AJ and VOROMOTORS! this video helped me fix so many loose bolts that were on my refurbished model. i was worried i was going to have to do a full stem replacement. little did i know i just had to get to the 2 bolts behind the rubber guard :) Good ol me just overthinking every little lose part.
Just finished tightening the stem neck and I have to get under the front wheel. Well it’s not easy time consuming for the first time. Added note take phots or video before removing anything, because putting it back for the first time will be annoying. 4pm to 8 pm that’s how long it took me and younger sister. 😂. I was smart I had help. Putting the brakes back will be the challenge.
Thanks mate 😀 Any tips on preventing the front suspension from ‘clanging’ so much over cracked pavements and small potholes?
This is OUTSTANDING!!!!!! Well done Voro! Two Thumbs Up!
Thank you! We will make sure to keep up to this standard!
drink every time he says "go ahead and"
Got my Cruiser yesterday so far I’m loving it! Although the front wheel and tbar aren’t aligned. Tried forcing it to align with the lever (height adjustment) loosen but it won’t barge. Please help!
Appreciate these videos so much. Very helpful
I purchased my emove Christmas 2023, it's been 6 months and I've used it a handful of times and it no longer charges. Tried everything, how can a charger go bad after 6 months? Very disappointed! Looks like this is not an isolated issue.
at 4:32 do not tighten these screws! They will break off and you will have to buy a new stem $190. At first you might think this is an easy fix pull the cables through replace stem and once again pull cable back up. The cable does not fit thought the stem. You have to open up the controller compartment an unhook 3 clips and pull the clips off. The clips are to big to pull through the stem hole. Once you rerun your cable you have to reattached the clips hot glue them and clip them back to their counter parts coming from the controller. You also have to pull you break lines out as well. th-cam.com/video/XNcUPPO2mbw/w-d-xo.html How to replace your main line on your emove cruiser
Mate, can you tell me why my fully charged emove just shut down power on me this morning on my way to work. Completely shut itself down.
One tip for setting full hydraulic brakes is to loosen the caliper mounting bolts and then squeeze the brake lever. With the brake lever held, re-tighten the mounting bolts. This *should* center the caliper on the rotor.
Multifaceted fitting at the end of the stem would keep it from getting that far outta alignment. Right?
The star at the bottom is screwed onto the stem. So, couldn’t you potentially break the star, when trying to straighten the handlebars?
Wahoo!
This is how to do all tutorials only problem is, how to remove the front fender to get to those stem bolts, lol. If things get too difficult, it won't be done lol.
Hi i have kugoo m4 and the steering wheel is wobbly how can i fix it?
I hear there are some issues with the rear fender becoming loose. Anyone experienced this? Drove me crazy on the Apollo Explore. I was tightening the screws after every ride.
Hi,
There has not been a reported issue with our rear fender.
If you have any further questions, please do not hesitate to email support@voromotors.com or call us at 3237097329
Hope this is helpful!
100%. What happened to me..had to keep tightening EVERY RIDE. The screws didn't even grip and it fell off mid ride...almost ate the concrete during it. Very much a bummer situation 😭😭
My brakes make some weird noises. They move freely when I have the wheels off the ground so now brake rub. Also my bars have meat on them. What the hell could it be?
Sweeeeeet 💯🔥🔥🔥
Thanks AJ! Your vids are excellent and very helpful. Keep up the great job!
Duane
Merry Christmas AJ,
After trying to tune my back brake, I found that the pad failed to rubb against the disk brakes. Any help for me please?
Hi Oliver,
Can you please email to support@voromotors.com ? Our customer service team will definitely be able to take care of you.
@@VoroMotors
Ok, thanks!
On those XTech's there's also a tiny Allen screw that adjusts the piston pressure that's not mentioned here. I was doing all the adjustments via tightening the cables at the three points but this other screw that's not mentioned adjusts the pre-pressure and THAT is what I've been told you adjust as the pads wear in, not the cables. If it'll let me share this link, I've pointed at the screw I'm talking about: i.imgur.com/5DugQt0.jpg
My rear break is so loose I ant feel it at all its to the point where I have to spend money to get someone to look at it and help me adjust it
Hey dudes, regarding adjusting the brakes I saw you did 3 different adjustments for tightening them. Both of my brake levers are very loose and i can pull them almost full range before i feel the brakes kicking in. Which method do I do... First? Second? Third? Thanks!
the 1st method, its the easiest in my opinion! then tune the feel with the 2nd and 3rd! - AJ
@@VoroMotors thanks!
Doesn't work for me. Every morning I have little to no brakes.
oi.....r u one of the main casts of tha TV series "The Strain"?.......ON NETFLIX 'N'OTHER PIRATE SITES
My handle bars are stuck. I think it’s because I did the tightening of the handle bars
My rear is braking weird it spins out
Wish I’d watched this to start with instead of wasting 2 hours
Hi Voro, I ordered 2 handlebar extensions that can be seen from 00:46 to 1:00 in this video. I've been trying to get help from you guys
Hey, I think I might know who you are. I believe one of my colleagues have helped you with it!
@@VoroMotors you did! Thank you very much! I have multiple social media personalities...this is not my main... Was blanketing for help... You guys are awesome!🙏🏼🙏🏼🙏🏼
Can I replace the coils at the shock absorver for an hidraulic?
Can I replace the calipers for hidraulic deores ones?
Hi...i have an emove touring scooter....after 4 days, of use, the front tire went flat....no puncture, looks like the inner tube just popped / failed. Voro gang - can you guys please post a video that shows how to take off front tire of Emove Touring, and replace the inside inflatable ture? help! thank you.
How did you do it ? I have the same problem!
dan ian Do they have a tutorial for touring tire?
Hello can you help me how to fixe my signal lights of emove cruiser can you make a tutorial thank you
Hi Federico,
Can you email us at support@voromotors.com to find out specifically the issues you want to fix?
Looking forward to assisting you.
This made my scooter looser on the brakes
you need a microphone :D cost 5$
This is joey?
In the beginning of the video he said his name was AJ. Joey is likely another gentleman altogether. Cheers.
joey is a fantasy name they all use.
Rain reviews - very false information. few rides in rain and mine died after 3 months of riding. their warranty doesnt cover anything water related. i even purchased 2 extra years warranty and now voided.... I need to pay for following
battery $490
controller $50
motor $295
throttle $42
walt meter $45
plus i need to pay $37.50 at the shop for inspection plus labor time $.
i hope you're a actor and not a mechanic at 8.10 minutes you just unlock the adjustment lock nut hope no one gets in a crash because adjustments screw went in and no more breaks,sorry but that lame,🤕😱.put a real mechanic,or analyze the content let's say i go 17mph hey i miss the stop by only 4 feet BANG I'M DEAD.