You are indeed a good shop and an asset to your community. To take something in that somebody worked on first is truly old school. I have in the past used the old bearing as a support when pressing in the new one. The very first VW Rabbits used to go through them with regularity. I heard they found the grease they were using was a dielectric and causing static arching while rotating, pitting the race. They added graphite to the grease to bleed off the charge and the problem went away. That was the urban legend at the time.....
Yeah I remember my buddy messing up my wheel bearing when helping out, ended up damaging it. Had to bring the spindles in and they pressed them right then for like $40 or something, they have had a lot of business from other people I know because they're good guys. I also remember seeing the mechanic on his boat one time, doing great work and doing well that's what I like to see.
Most excellent, enjoyed. When I was a younger dude, I remember using some dry ice and throwing parts in the oven, to my Mom’s fury. From what I can recall they just about dropped in. Getting the bearings out !, I seem to conveniently have no memory of that deed. Many thanks.
My top tip for using a shop press is simply to know when to quit when something doesn't want to move. Applying too much force will mean that you will damage the press and/or the part (if you are lucky) or it'll suddenly release a couple dozen tons of pressure in whatever direction it feels like going and it might feel like coming YOUR way.
its my experience that if it isn't moving, than your rig is wrong. 2 variables. i've only ever had to help new guys. and i really only work on 1/2 ton through fwd toyota's. so my experience is limited.
An air hammer tap-tap-tapping on the component does wonders to help things move along. I have a round semi-polished bit I created which doesn't get used often. But, when it does, it works wonders.
I also went with a 20 ton. It struggled with the first bearing so I just flipped it a few times applied pressure until it popped loose. Had I gone with a smaller press I would have been stuck... thanks for the video I've never had press in hubs just assembly hubs so this was a great video. Simple, to the point and you can SEE what you are doing! Thanks again all these years later!
Just what I was looking for, after searching the internet, and even the Toyota forums I finally stumble on your video and saw what I was searching for. So simple and inexpensive. Thank you so much for your video.
I wish I could work with someone like you. You are a great teacher and I will be following more of your work. You got me out of a bind, thank you for that, man. Awesome video!
I changed out the press-in bearing on my 92 Taurus SHO at the auto skills center on Schofield Barracks, Hawaii. The mechanic on location told me to replace the hub as well, because it was loose inside the new bearing, just fell right in!! I didn't take his advice and just cranked down the hub nut good n' tight!! The mechanic told me this wouldn't last long, but I did it anyway! Five miles into the test drive the bearings started making this coffee grinder sound! Had to do the whole job all over again with all new parts and a new hub!! Rookie mistake!!;-) I always buy the kit that includes the bearing, snap-ring and the hub. Great video, as always, Eric! You're my new TH-cam bro!!
Thanks for the nice demo. I will not be beating on the bearing as I have just ordered a 12 ton Press to do the bearings on my 2004 Honda Civic. I will also have to do the 2004 Honda CR-V in the spring. Your demo showed me what not do do and I like that. Please keep up the great demos. Have a great day - John
Really helpful video ... thanks for sharing. I bought a 20t press to remove/replace ball joints on my old VW Beetle Nova/Sterling kit car, which it did perfectly. I now need to replace a wheel bearing on my daughter's Citroen DS3 and you've shown me how to do this with my press ... Thanks mate! :)
I bought a Harbor Freight 20 ton press years ago and absolutely LOVE it. A few months ago, the jack started leaking. Rather than buying a new press, I replaced the jack with an air/hydraulic, also from Harbor Freight. I LOVE my press even more now!
I debated buying a press for years, thinking I'd hardly use it. Now that I have one, I use it all the time! It works great for straightening or bend just about anything (on purpose lol). It has also saved my bacon many times to hold something that the vice would not. I replaced an International high pressure oil pump that drives the injectors and there was nothing I could find to hold the helical cut gear to loosen the nut. With the press and some 2x4s to "clamp" the gear without damage, I was able loosen the nut, replace the pump and tighten the nut to spec. Without the press, I don't know what I would have done.
Great job on the video! No nonsense, straightforward, excellent tips and no crappy music playing in the background. I am going to check out your other videos. I like your approach, if you lived nearby I would give you some business,Thanks for your time and the good info.
And i really need to reiterate what has been said, that my friend was the best video of its kind! There is now a fresh bearing installed in my 97 Rav 4.1 hub. Thank you for your clarity and concise description's. You have gained a subscriber and a like, Cheers
Great informative video Mr. O ....ive never seen a wheel bearing pressed out or in before so i couldnt wait to watch this video !! You are now my favorite auto channel ...i like ChrisFix and ETCG as well too !! and i actually spent prolly almpst 24 hours straight just watching your videos like a marathon !!! Your diagnosing skills are the best ive ever seen !! Your a real AUTO MECHANIC MASTER !!! KEEP EM COMING !! thanks .... Phil S. Toledo, Ohio
As always your commentary along the way makes the difference. Thank you for posting informational and entertaining videos. You have officially replaced any automotive show on TV.
i bought one last week at first i bought the 12 ton i figure its good enought it turned out its a piece of shit then i decided to replace it with 20 ton and man its so much easier to press a wheel bearing out. i dont know why i keep walking in my garage and realy loving this press im thinking about adding more tooling to this its so cool.
Short and sweet video when you are "pressed" for time :-) I had Pepboys press a bearing in for me and clear as day, the instructions warned them of the ABS tone ring. Needless to say they screwed it up. They told me I should have warned them. I just bought my own press after that experience.
Had a similar bad experience at PepBoys. Found the helper wailing with a BFR on something in the engine compartment when the job was underneath. Showed him the location and got my vehicle back. Happy ending? He left a SnapOn 3/8" drive 24" extension in the engine bay.
Eric, Thanks for the vid - very helpful. Getting that bearing out is usually the hardest bit. Requires some decent force, pressing in as well as out, and once it gets going make sure you keep going because it's getting ready to get you back if you stop. :-)
I've worked with so many people who take the whole spindle out and use the press because they say it's the best way. we're I work now I was removing the whole spindle and pressing in and out bearings then I seen your video with a Toyota I think using the hub tammer and I was like that's awesome I need one of those. then I was telling my boss about the hub tammer and he's like oh we got on of those in the back and its exact kit you have and I've been using it ever since. I work with this other guy even though he knows we have a hub tammer he still chooses to remove the whole spindle and use the press. oh well his loss I guess lol thanks for making great videos and keep up the good work.
The biggest mistake I ever made was cheaping out when I bought a press. For anyone considering buying one, put some money into it! Yeah, the cheap ones will get the job done, but the amount of time you'll spend fiddling around with it trying to get things to fit will be frustrating to no end. A good assortment of arbors helps a lot, too! Great video, Eric! That hub didn't give you any trouble at all! :D
I've had a press for 35 years and only used it maybe 20 times. When you need it, you gotta have it. But the set up shimming time is a killer. For bearings, even drop offs like this one, I still use my OTC GRAPPLER. Much quicker, easier set up and I DON'T have to pull it off the car saving having to send it out for an alignment.
When I was a mechanic years ago, I built up a collection of old outer races which I ground down a tad to make perfect drivers for next time. I still have them somewhere, along with a lot of inner spacers and thick washers etc all kept together on a f'kin' long bolt. It seems young mechanics haven't learnt the basics of never pressing 'through' a bearing. It will shorten their life a lot.
Thanks bud. Extremely informative and helpful to me. I'm a handy guy, but not too familiar with a 60 ton press. You set me straight on that. Thanks again.
20 ton Harbor Freight examples can be picked up via Craigslist for under a C note. And with all the add-ons from SWAG Offroad, it becomes quite the DIY shop workhorse. Check out the gibs I fabricated to remove the ram slop from the cheapie press: th-cam.com/video/X6zGj9avKIQ/w-d-xo.html
Those bearing presses....life savers, I only have a 12 toner at home use it once in a blue moon but glad it was there last weekend for 2 rear wheel bearings.
I have the 20 ton from Harbor Freight. Picked up cheap on Craigslist. With the bending tackle from SWAG Offroad, I use it on all kinds of non-automotive projects. Here's how I removed the slop from the ram: th-cam.com/video/X6zGj9avKIQ/w-d-xo.html
I was working in our truck shop, and had to press off a drive shaft yoke to replace a carrier bearing. Because the drive shaft was too long, we picked up the press with a fork lift put pallets under both sides set up the drive shaft. Our press is 100 tons. I was watching the pressure gauge and it took ( to my surprise) 26 tons to break it loose then 23 tons to keep it moving. After I replaced the carrier bearing which was easy had to press the yoke back on. I used anti seize it still took nearly 15 tons to press it back on, after the splines and yoke were cleaned. A press is a great tool, even if you don't need it very often. I realize a 100 ton press is a bit much, still it made fast work of an otherwise tough job.
I have been waiting for this as a comparison to your wheel bearing change on the Toyota Corolla where you showed how to do it on the car. Thanks for this!
Great video! I did a lot of press in bearings back in the 90's and early 2000's. I thought they had fallen out of favor in the industry but apparently Kia was still using them in 2013. Been a while since I've done one so watched your video as a primer. I'm just a shade tree mechanic.
I miss my presses . Had both 12 and 20 tons. The 12 was great for u-joints. Made many " press toys" over the years. Black Pipe (schedule 40) makes for good cups. Great job on supporting the knuckle assembly. With that type of press it is important to make sure everything is straight, otherwise if off the jack will "kick out" and bend the guides. One day a "hippie" I worked with asked to borrow my press . After the morning "wake and bake" , he managed to bend the guides! Needless to say I was not very happy!
Thanks for the video. I had a local shop change out my front press in bearings because I did not have a press and did not want to buy one for a one time use. Plus, did not know what kind of gremlins may pop out in the process. Gave the shop the whole job $200 labor and $200 bearings, highest end bearings available at NAPA.
+South Main Auto Repair The shop I went to was in Bloomsburg, PA, the sticks. Priced the same job in a shop in Stamford, CT. They wanted $200 labor per wheel.
Thanks! I know this is an old video but the algorithm comes through again! I have the tools (Well not the press,,...Yet!) from a whole hutch of VW Bunnies. But this was highly educational for any body who wants to know How the wheels on the bus go round and round.
fantastic video, i will be replacing both rear wheel bearings on my ford falcon soon. i will be using a 20 ton press, using your tips this should go easy.
Thanks for this. Haven’t used my shop press much and using the Astro bearing puller kit doesn’t work well for me off of the vehicle. Just finished up a perfect set of civic front knuckles after forgetting to support the inner race on the first one. Great vids as always and I always refer to your catalog of videos if I’m ever in doubt. Thanks again.
I enjoyed this video. It's nice to see someone who knows what he's doing and explaining it while he's doing it. The lack of music was especially nice. I cringed when you put it back together without replacing the missing wheel lugs and without a new circlip. It's the definition of half-assed in my book. It seems to me that you could be exposing yourself to some liability if the customer uses it that way and has an accident down the road.
Thanks for talking me out of getting a Harbour Freight press for my 15yo. We can pay a shop to put new wheel bearings in his 79 vette. I wouldn't know where to get all the additional blocks or sleeves needed for pressing.
Good job showing how to press bearings really helps with a press, I got a little press but I use a cutting torch lots of time on bearings guess not the best way but I am fairly good with a torch.
Kind of amazing how something pretty simple can make some jobs really easy . I've used one for doing all kinds of jobs once even to change U joints. Seems like over kill I know but made the job very easy
I can confirm that you don't want to press on the small ears of the knuckle. I had a mechanic snap one off of my knuckle on a road trip of mine, which meant I was stuck in Murrysville PA for three days until a new knuckle arrived. Of course he had a lot of motivation to get the job done asap--the car was parked in the entrance of his shop, minus one wheel!
Good video. Maybe next time you can show using a torch to heat up and expand the assembly or cut off the race, or even using a cutoff wheel to cut the race , being careful not to knick the hub. *Btw I hope Scotty appreciates you helping him out. There's only so much you can do in the driveway and a big hammer.*
Use a dremel cutoff wheel. Cut it down almost through and then use a flathead and a hammer on the cut to fracture it there. The ring will let go and slide off.
I've used a 100 ton press, made a cage to go around it so the shrapnel does little damage. But there is always the time you have to use a torch, arc gouge, plasma torch, or cut off wheel.
Really well put together video. There's lots of these wheel bearing press videos that seem to leave important parts out. I've got a 20 ton press and after installing the inner race back into the bearing I just cannot get the thing to pop. Should I heat it up, put it in the freezer or?
I screwed up and didn't support the inner race while pushing in the hub. Initially the hub didn't want to spin then i heard a slight pop and it would spin. Think I messed up the new bearing more than the old one was. Thanks for this video Eric.
If only I had even a 5 ton press I wouldn't have struggled for near 15 mins with BkrBars & pipe to press oout the bearing. 40$ for AZone junk bearing! WOW Timken and SKF are the best and can be gotten from famous online auto parts store for 26-29$. Great pointers, thats why I watch your video's, saves me from gotcha type mistakes.
After you grease your bearings toss em in the freezer for a few hours or overnight. Get everything set then get it. It will shrink a tiny bit a press in a bit easier. Thermal dynamics really makes getting metal fasteners apart. Heat to expand cool to shrink! Really helps with anything press in!
I think I know exactly why this customer is replacing their hub bearing. Happened to me several years back on my wife's car. She had taken it to a certain big box store to have a tire fixed and they cross threaded a couple of the lug nuts. So when I had to remove the wheel a year or so later, two of the lug studs broke off. The hub is so close to the knuckle/carrier that the only way to get new studs in is to remove the hub from the bearing, and as you see here extracting the hub can cause the bearing to come apart. Plus, it didn't make any sense to go to all that work pressing the hub out of the bearing to press it back in to an old bearing. It looks like this hub has plenty of clearance but looks can be deceiving.
Most videos I've seen cut a diagonal into the hub race to get it off, but the few times I've tried I've been able to use a puller to remove them, and pretty easily at that. Some press-in bearings can actually be reused so why destroy when you could have a decent backup in case you need one.
Thank you for the info. I love your videos. I have a quick question, though. I forgot to add my Snap rings. What will happen to my car. If I just put it on without it? And can u just press it back out just enough to get it in there? I look forward to your answer
Hi , in the Uk I can't think of a bearing which does not with a new snap ring and a new hub nut where need and i've done a few in the last forty years ! A mate in Australia says they don't come all in one kit either.
The idea this gives me is that I want a shop press!! I've had to pay someone to do the pressing for me in a real stubborn case on a Mitsi. That's a great looking press, worth a bomb no doubt even second hand. The Chinese ones are pretty cheap, and I guess should be ok within their prescribed limits, I'm thinking a 20 ton should do most car stuff.
I snapped one of the ears off an escape recently at my dealership I was able to get a used one from the junk yard the next big purchase I make will be a wheel bearing kit to do it on the car
I bought one of those to replace press-in front wheel bearings and it worked perfectly for it. I got the Astro-Pneumatic which is heavy duty. But it won't remove the hub from the knuckle in most situations. I usually just remove the knuckle and punch it out or use a press.
I think one of my favorite details about this video is when you hit what the camera is on. It makes it feel real. :) (Of course it's real, but more real as an observer.)
After watching you use the hub tamer ...it’s on my purchase list lol ...it takes too long to press in bearings and in WV if it’s old enough to need a bearing you can bet it’s rusted ...I use a lot of PB blaster lol
+motoYam82 I agree but you always see so many secondary just in case engineered the world ends gismos attached like the red wiring harness clips just there because you always see them falling off too LOL. Just one of those things that keep me up at night just wondering why, oh why :)
Don't lose too much sleep, Steve! In this case the engineering fail-safe would be the cotter pin to keep the axle nut from falling off, right? And red wiring harness clips are plain annoying!
....people , sometimes when they have old "plasticized" tires that make a lot of road noise, they are replacing the wheel bearings for some reason .... and only after , a new set of tires ... :)
+South Main Auto Repair - Eric, you forgot the must important law when working with plumbing, it's like the Holy Grail of plumbing, the law of gravity plays a big, big role, Always, Always work above the water ! Not below it ! ! ! LOL !
Timken makes their shit in china and outsources to other brands, they have been advertising their chinese factory for years now. Last 3 bearings from Timken I have received were all bad right out of the box.
This was always the scariest part for me. The shop I worked at had a press like that but with a gauge and when it kept climbing it was like in fucking das boot, waiting to die or lose an eye at least. The forces in play are crazy.
Oh man, you're not kidding. I had an old socket blow-- a shard from it flew out the back side, ricocheting from the floor, to the back wall, the off the ceiling and I don't know where it went after that. Initially I thought a bullet hit my shop. Rigging up a plexiglass shield is on my list.
Why didn't you use your red spray grease on the outside of the bearing before pressing it in. I just purchased the 3 can package from your SMA parts site, it works great. THANKS FRIEND
Love your videos! My first question ever. Here it goes and don't laugh at me. I removed a front wheel bearing on a 2004 Honda CRV for the first time. I watched videos on how to do it and that it was important to install the new bearing with the brown side to the back. My neighbor came over to see what I was doing at said that the brown side went to the front because the numbers go to the front. I looked at the bearing and looked the same both sides so we installed it with the brown side to the front and guess what after I finished installing everything and went for a test drive the stupid ABS light came on. RATS! My question: Can I press the bearing out and turn it around or do I just need to buy a new bearing? Thank you in advance.
Diana's World Of Fixing Things Sure you figured it out by now, but if not, I'd just bite the bullet and get a bearing. Your neighbor suffers from a common condition, where he believes his past application applies to all vehicles. I've seen somebody use tranny fluid in a steering system because they must've seen it done on a Ford or something. In my old Taurus, you used trans fluid in the power steering, but it was not the same for the poor sap driving the Grand AM. This is where a manual can help guide you as you learn, and allow you to cross reference advice from lesser known youtubers, who might not be qualified (I've seen dangerous info on YT). It's not religion, but it'll help you on little specs like that, and I'd surely take it's word over your neighbor's next time 😕. On the bright side, you'll be a master on changing a Honda CRV bearing. .Have a beer 🍻
Out of the other wheel bearing pressing videos on TH-cam this is the most helpful one by far. Thanks
You are indeed a good shop and an asset to your community. To take something in that somebody worked on first is truly old school. I have in the past used the old bearing as a support when pressing in the new one.
The very first VW Rabbits used to go through them with regularity. I heard they found the grease they were using was a dielectric and causing static arching while rotating, pitting the race. They added graphite to the grease to bleed off the charge and the problem went away. That was the urban legend at the time.....
Yeah I remember my buddy messing up my wheel bearing when helping out, ended up damaging it. Had to bring the spindles in and they pressed them right then for like $40 or something, they have had a lot of business from other people I know because they're good guys. I also remember seeing the mechanic on his boat one time, doing great work and doing well that's what I like to see.
Most excellent, enjoyed. When I was a younger dude, I remember using some dry ice and throwing parts in the oven, to my Mom’s fury. From what I can recall they just about dropped in. Getting the bearings out !, I seem to conveniently have no memory of that deed. Many thanks.
My top tip for using a shop press is simply to know when to quit when something doesn't want to move. Applying too much force will mean that you will damage the press and/or the part (if you are lucky) or it'll suddenly release a couple dozen tons of pressure in whatever direction it feels like going and it might feel like coming YOUR way.
its my experience that if it isn't moving, than your rig is wrong. 2 variables. i've only ever had to help new guys. and i really only work on 1/2 ton through fwd toyota's. so my experience is limited.
An air hammer tap-tap-tapping on the component does wonders to help things move along.
I have a round semi-polished bit I created which doesn't get used often. But, when it does, it works wonders.
I also went with a 20 ton. It struggled with the first bearing so I just flipped it a few times applied pressure until it popped loose. Had I gone with a smaller press I would have been stuck... thanks for the video I've never had press in hubs just assembly hubs so this was a great video. Simple, to the point and you can SEE what you are doing! Thanks again all these years later!
Just what I was looking for, after searching the internet, and even the Toyota forums I finally stumble on your video and saw what I was searching for. So simple and inexpensive. Thank you so much for your video.
Glad you liked it!
I wish I could work with someone like you. You are a great teacher and I will be following more of your work. You got me out of a bind, thank you for that, man. Awesome video!
I changed out the press-in bearing on my 92 Taurus SHO at the auto skills center on Schofield Barracks, Hawaii. The mechanic on location told me to replace the hub as well, because it was loose inside the new bearing, just fell right in!! I didn't take his advice and just cranked down the hub nut good n' tight!! The mechanic told me this wouldn't last long, but I did it anyway! Five miles into the test drive the bearings started making this coffee grinder sound! Had to do the whole job all over again with all new parts and a new hub!! Rookie mistake!!;-) I always buy the kit that includes the bearing, snap-ring and the hub. Great video, as always, Eric! You're my new TH-cam bro!!
Thanks for the nice demo. I will not be beating on the bearing as I have just ordered a 12 ton Press to do the bearings on my 2004 Honda Civic. I will also have to do the 2004 Honda CR-V in the spring. Your demo showed me what not do do and I like that. Please keep up the great demos. Have a great day - John
I second Eric's statement. When you need a press, you really need it! Great Video.
Really helpful video ... thanks for sharing. I bought a 20t press to remove/replace ball joints on my old VW Beetle Nova/Sterling kit car, which it did perfectly. I now need to replace a wheel bearing on my daughter's Citroen DS3 and you've shown me how to do this with my press ... Thanks mate! :)
I bought a Harbor Freight 20 ton press years ago and absolutely LOVE it. A few months ago, the jack started leaking. Rather than buying a new press, I replaced the jack with an air/hydraulic, also from Harbor Freight. I LOVE my press even more now!
And making the HF 20 ton more precise is rather easy:
th-cam.com/video/X6zGj9avKIQ/w-d-xo.html
The extra explanations make your video a standout. Bravo.
I debated buying a press for years, thinking I'd hardly use it. Now that I have one, I use it all the time! It works great for straightening or bend just about anything (on purpose lol). It has also saved my bacon many times to hold something that the vice would not. I replaced an International high pressure oil pump that drives the injectors and there was nothing I could find to hold the helical cut gear to loosen the nut. With the press and some 2x4s to "clamp" the gear without damage, I was able loosen the nut, replace the pump and tighten the nut to spec. Without the press, I don't know what I would have done.
Big fan of your videos Mechanic myself of 42 years, Keep on wrenching my friend
Great job on the video! No nonsense, straightforward, excellent tips and no crappy music playing in the background. I am going to check out your other videos. I like your approach, if you lived nearby I would give you some business,Thanks for your time and the good info.
It's nice of you to put these video's out , It not only shows the how to part of it but how to do it safely.
And i really need to reiterate what has been said, that my friend was the best video of its kind!
There is now a fresh bearing installed in my 97 Rav 4.1 hub.
Thank you for your clarity and concise description's.
You have gained a subscriber and a like, Cheers
Glad I could help!
Great informative video Mr. O ....ive never seen a wheel bearing pressed out or in before so i couldnt wait to watch this video !! You are now my favorite auto channel ...i like ChrisFix and ETCG as well too !! and i actually spent prolly almpst 24 hours straight just watching your videos like a marathon !!! Your diagnosing skills are the best ive ever seen !! Your a real AUTO MECHANIC MASTER !!! KEEP EM COMING !! thanks ....
Phil S. Toledo, Ohio
As always your commentary along the way makes the difference. Thank you for posting informational and entertaining videos. You have officially replaced any automotive show on TV.
The harbor freight press is really good I recommend it to anyone who needs a press at home.
i bought one last week at first i bought the 12 ton i figure its good enought it turned out its a piece of shit then i decided to replace it with 20 ton and man its so much easier to press a wheel bearing out. i dont know why i keep walking in my garage and realy loving this press im thinking about adding more tooling to this its so cool.
Swap the hydraulic jack with their 20ton air jack. So much easier
I have the same press, bought it 40 years ago. Great job on the bearing Eric 🇨🇦
Short and sweet video when you are "pressed" for time :-) I had Pepboys press a bearing in for me and clear as day, the instructions warned them of the ABS tone ring. Needless to say they screwed it up. They told me I should have warned them. I just bought my own press after that experience.
Had a similar bad experience at PepBoys. Found the helper wailing with a BFR on something in the engine compartment when the job was underneath. Showed him the location and got my vehicle back. Happy ending? He left a SnapOn 3/8" drive 24" extension in the engine bay.
Eric, Thanks for the vid - very helpful. Getting that bearing out is usually the hardest bit. Requires some decent force, pressing in as well as out, and once it gets going make sure you keep going because it's getting ready to get you back if you stop. :-)
I've worked with so many people who take the whole spindle out and use the press because they say it's the best way. we're I work now I was removing the whole spindle and pressing in and out bearings then I seen your video with a Toyota I think using the hub tammer and I was like that's awesome I need one of those. then I was telling my boss about the hub tammer and he's like oh we got on of those in the back and its exact kit you have and I've been using it ever since. I work with this other guy even though he knows we have a hub tammer he still chooses to remove the whole spindle and use the press. oh well his loss I guess lol thanks for making great videos and keep up the good work.
The biggest mistake I ever made was cheaping out when I bought a press. For anyone considering buying one, put some money into it! Yeah, the cheap ones will get the job done, but the amount of time you'll spend fiddling around with it trying to get things to fit will be frustrating to no end. A good assortment of arbors helps a lot, too!
Great video, Eric! That hub didn't give you any trouble at all! :D
Nice, down to earth video on how it's done. Fine Job !!
I've had a press for
35 years and only used it maybe 20 times. When you need it, you gotta have it. But the set up shimming time is a killer. For bearings, even drop offs like this one, I still use my OTC GRAPPLER. Much quicker, easier set up and I DON'T have to pull it off the car saving having to send it out for an alignment.
When I was a mechanic years ago, I built up a collection of old outer races which I ground down a tad to make perfect drivers for next time. I still have them somewhere, along with a lot of inner spacers and thick washers etc all kept together on a f'kin' long bolt. It seems young mechanics haven't learnt the basics of never pressing 'through' a bearing. It will shorten their life a lot.
Thanks bud. Extremely informative and helpful to me. I'm a handy guy, but not too familiar with a 60 ton press. You set me straight on that. Thanks again.
20 ton Harbor Freight examples can be picked up via Craigslist for under a C note. And with all the add-ons from SWAG Offroad, it becomes quite the DIY shop workhorse. Check out the gibs I fabricated to remove the ram slop from the cheapie press:
th-cam.com/video/X6zGj9avKIQ/w-d-xo.html
Those bearing presses....life savers, I only have a 12 toner at home use it once in a blue moon but glad it was there last weekend for 2 rear wheel bearings.
I have the 20 ton from Harbor Freight. Picked up cheap on Craigslist. With the bending tackle from SWAG Offroad, I use it on all kinds of non-automotive projects.
Here's how I removed the slop from the ram:
th-cam.com/video/X6zGj9avKIQ/w-d-xo.html
I was working in our truck shop, and had to press off a drive shaft yoke to replace a carrier bearing. Because the drive shaft was too long, we picked up the press with a fork lift put pallets under both sides set up the drive shaft. Our press is 100 tons. I was watching the pressure gauge and it took ( to my surprise) 26 tons to break it loose then 23 tons to keep it moving. After I replaced the carrier bearing which was easy had to press the yoke back on. I used anti seize it still took nearly 15 tons to press it back on, after the splines and yoke were cleaned. A press is a great tool, even if you don't need it very often. I realize a 100 ton press is a bit much, still it made fast work of an otherwise tough job.
I have been waiting for this as a comparison to your wheel bearing change on the Toyota Corolla where you showed how to do it on the car. Thanks for this!
Great video! I did a lot of press in bearings back in the 90's and early 2000's. I thought they had fallen out of favor in the industry but apparently Kia was still using them in 2013. Been a while since I've done one so watched your video as a primer. I'm just a shade tree mechanic.
I miss my presses . Had both 12 and 20 tons. The 12 was great for u-joints. Made many " press toys" over the years. Black Pipe (schedule 40) makes for good cups. Great job on supporting the knuckle assembly.
With that type of press it is important to make sure everything is straight, otherwise if off the jack will "kick out" and bend the guides.
One day a "hippie" I worked with asked to borrow my press . After the morning "wake and bake" , he managed to bend the guides! Needless to say I was not very happy!
Thanks for the video. I had a local shop change out my front press in bearings because I did not have a press and did not want to buy one for a one time use. Plus, did not know what kind of gremlins may pop out in the process. Gave the shop the whole job $200 labor and $200 bearings, highest end bearings available at NAPA.
+Sandbag1300 I charged the guy $30. Most cases I get .5 to 1 hour labor to R&R bearings if you bring in the knuckle
+South Main Auto Repair The shop I went to was in Bloomsburg, PA, the sticks. Priced the same job in a shop in Stamford, CT. They wanted $200 labor per wheel.
Thank you for this video. I'm attempting to press the bearings and hub together on my husband's car. Wish me luck!!
Good tips on press use. You don't need them a lot but when you do you really do.
Mine is a "go to" tool.
I bought a smaller 12 ton press. Best $100 bucks I’ve ever spent! A 25 ton press is sure next when I get more room for a shop!
So what applications do you have in mind for a 25 ton press?
I have a 12 ton pipe bender, only used it once. But I needed it.
@@hashiramasenju4846 I was thinking of getting a 12 ton press, Is it strong enough to press out a bearing in a climate that experiences corrosion?
One of those videos where all the pieces of the jigsaw come together because of a great instructor! 👍👍👍
Thanks! I know this is an old video but the algorithm comes through again! I have the tools (Well not the press,,...Yet!) from a whole hutch of VW Bunnies. But this was highly educational for any body who wants to know How the wheels on the bus go round and round.
I use a bearing separator alot on these hub bearings. It works well for mounting spindle on the press.
Nice video, sir. It's so nice watching senior mechanic do his job. :)
fantastic video, i will be replacing both rear wheel bearings on my ford falcon soon. i will be using a 20 ton press, using your tips this should go easy.
Thanks, man. Wish I had watched your video sooner. I went through two bearings before I figured out I had to support the underside.
that was helpful. the best wheel bearing replacement video
very well explained with lots of info and good camera work thanks!
Thanks for this. Haven’t used my shop press much and using the Astro bearing puller kit doesn’t work well for me off of the vehicle. Just finished up a perfect set of civic front knuckles after forgetting to support the inner race on the first one. Great vids as always and I always refer to your catalog of videos if I’m ever in doubt. Thanks again.
Awesome video, wish i watched it first before i broke one of my bearings pushing the hub in. Doh! Now i know to support the center.
I enjoyed this video. It's nice to see someone who knows what he's doing and explaining it while he's doing it. The lack of music was especially nice. I cringed when you put it back together without replacing the missing wheel lugs and without a new circlip. It's the definition of half-assed in my book. It seems to me that you could be exposing yourself to some liability if the customer uses it that way and has an accident down the road.
I get the feeling this may have been a cash job.
Excellent video. I appreciate your caution and the way you take the time t do things right.
I bought a shop press for like 50 bucks so glad I did I never thought I would need it as much as I do now, both my cars take press in bearings
Thanks for talking me out of getting a Harbour Freight press for my 15yo. We can pay a shop to put new wheel bearings in his 79 vette. I wouldn't know where to get all the additional blocks or sleeves needed for pressing.
Good job showing how to press bearings really helps with a press, I got a little press but I use a cutting torch lots of time on bearings guess not the best way but I am fairly good with a torch.
Your videos are the best keep them coming! Cant believe you don’t have a million subs but hopefully soon!!
I bought a harbor freight press years ago, it payed by itself within a year
I love mine. It isn't huge, but most of the time is enough to get the job done!
Kind of amazing how something pretty simple can make some jobs really easy . I've used one for doing all kinds of jobs once even to change U joints. Seems like over kill I know but made the job very easy
I can confirm that you don't want to press on the small ears of the knuckle. I had a mechanic snap one off of my knuckle on a road trip of mine, which meant I was stuck in Murrysville PA for three days until a new knuckle arrived.
Of course he had a lot of motivation to get the job done asap--the car was parked in the entrance of his shop, minus one wheel!
Good video. Maybe next time you can show using a torch to heat up and expand the assembly or cut off the race, or even using a cutoff wheel to cut the race , being careful not to knick the hub.
*Btw I hope Scotty appreciates you helping him out. There's only so much you can do in the driveway and a big hammer.*
Use a dremel cutoff wheel. Cut it down almost through and then use a flathead and a hammer on the cut to fracture it there. The ring will let go and slide off.
This is an awesome video and just what i needed to see to do the job myself. Very well thought out and a lot of good information. Thank you very much!
Thank you for the video...will be an interesting weekend but I feel much better having watched you do it. Thanks.
Thanks as always for your wisdom...keep up the great work in the PRNY
Very thorough video. It helped me significantly,learned a few tricks thanks
Nice one. Thank you for taking the time to help others. Be blessed.
I've used a 100 ton press, made a cage to go around it so the shrapnel does little damage.
But there is always the time you have to use a torch, arc gouge, plasma torch, or cut off wheel.
Really well put together video. There's lots of these wheel bearing press videos that seem to leave important parts out. I've got a 20 ton press and after installing the inner race back into the bearing I just cannot get the thing to pop. Should I heat it up, put it in the freezer or?
I screwed up and didn't support the inner race while pushing in the hub. Initially the hub didn't want to spin then i heard a slight pop and it would spin. Think I messed up the new bearing more than the old one was. Thanks for this video Eric.
If only I had even a 5 ton press I wouldn't have struggled for near 15 mins with BkrBars & pipe to press oout the bearing. 40$ for AZone junk bearing! WOW Timken and SKF are the best and can be gotten from famous online auto parts store for 26-29$.
Great pointers, thats why I watch your video's, saves me from gotcha type mistakes.
After you grease your bearings toss em in the freezer for a few hours or overnight. Get everything set then get it. It will shrink a tiny bit a press in a bit easier. Thermal dynamics really makes getting metal fasteners apart. Heat to expand cool to shrink! Really helps with anything press in!
I think I know exactly why this customer is replacing their hub bearing. Happened to me several years back on my wife's car. She had taken it to a certain big box store to have a tire fixed and they cross threaded a couple of the lug nuts. So when I had to remove the wheel a year or so later, two of the lug studs broke off. The hub is so close to the knuckle/carrier that the only way to get new studs in is to remove the hub from the bearing, and as you see here extracting the hub can cause the bearing to come apart. Plus, it didn't make any sense to go to all that work pressing the hub out of the bearing to press it back in to an old bearing. It looks like this hub has plenty of clearance but looks can be deceiving.
Thank you for making this look easy! So much better than other videos!
Hi Eric watched many of your video and thank you. Now for removing a race from hub all you need to do is torch it and it falls off the hub.
Eric where you got that gear puller from? Seems very strong, it pull that bearing race like nothing.
This is a terrific video. Lots of great tips. Thanks
Thanks for taking the time to video the process
Thanks Eric. I love those newer style GM hub bearings - talk about gravy work!
The shop press is definitely a nice addition to any shop. Not as important as an air compressor, but way up there ;)
Most videos I've seen cut a diagonal into the hub race to get it off, but the few times I've tried I've been able to use a puller to remove them, and pretty easily at that. Some press-in bearings can actually be reused so why destroy when you could have a decent backup in case you need one.
Thank you for the info. I love your videos. I have a quick question, though. I forgot to add my Snap rings. What will happen to my car. If I just put it on without it? And can u just press it back out just enough to get it in there? I look forward to your answer
Good morning Eric ...great video as usual sir!!!!
Hi , in the Uk I can't think of a bearing which does not with a new snap ring and a new hub nut where need and i've done a few in the last forty years ! A mate in Australia says they don't come all in one kit either.
I need to do the exact same thing. This has really helped out so much. Thank you. ;)
Good video! First time viewer and subscriber.
Thank you for showing us how to use it a press machine as well as that two prong crab on clamp that was sick
Thanks mate,that's a very good brief description/video appreciate it
The idea this gives me is that I want a shop press!! I've had to pay someone to do the pressing for me in a real stubborn case on a Mitsi. That's a great looking press, worth a bomb no doubt even second hand. The Chinese ones are pretty cheap, and I guess should be ok within their prescribed limits, I'm thinking a 20 ton should do most car stuff.
I snapped one of the ears off an escape recently at my dealership I was able to get a used one from the junk yard the next big purchase I make will be a wheel bearing kit to do it on the car
I bought one of those to replace press-in front wheel bearings and it worked perfectly for it. I got the Astro-Pneumatic which is heavy duty. But it won't remove the hub from the knuckle in most situations. I usually just remove the knuckle and punch it out or use a press.
Man you made one excellent video. Very educational.
I love the video man I learned a lot pressing stuff I just got a press so keep up the good work man
I think one of my favorite details about this video is when you hit what the camera is on. It makes it feel real. :)
(Of course it's real, but more real as an observer.)
This video was awesome man ! Appreciate the content.
After watching you use the hub tamer ...it’s on my purchase list lol ...it takes too long to press in bearings and in WV if it’s old enough to need a bearing you can bet it’s rusted ...I use a lot of PB blaster lol
Thanks for this video. I'm going to have to do mine on my Ssangyong Rexton SUV soon, so after watching this I know how to do it right, now.
It's amazing how the axle stub is only held in by a press fit, no secondary retainer like the bearing has. Nice vid....
+STEVE ROB Well the CV axle and axle nut should hold it together on the vehicle pretty tight if torqued to factory spec :)
+motoYam82 I agree but you always see so many secondary just in case engineered the world ends gismos attached like the red wiring harness clips just there because you always see them falling off too LOL. Just one of those things that keep me up at night just wondering why, oh why :)
Don't lose too much sleep, Steve! In this case the engineering fail-safe would be the cotter pin to keep the axle nut from falling off, right? And red wiring harness clips are plain annoying!
motoYam82 Thanks buddy im going for a nap right now.LOL
I always enjoy your videos!
....people , sometimes when they have old "plasticized" tires that make a lot of road noise, they are replacing the wheel bearings for some reason .... and only after , a new set of tires ... :)
Geeze, what time do you go to work 5am !!
Been helping my neighbor replace his septic system, Pressing wheel bearing sounds like alot more fun !!
+South Main Auto Repair - Eric, you forgot the must important law when working with plumbing, it's like the Holy Grail of plumbing, the law of gravity plays a big, big role, Always, Always work above the water ! Not below it ! ! ! LOL !
+Billy R I take that back, you did say shit flows down hill ! LOL!
What the tool you use to do it on car?
The cheap parts store bearings don't last. You'll be doing it again and again until customer gets a Timken or OEM bearing.
I just paid 300 bucks for a hub assembly on my truck with a lifetime warranty so if it goes at least I can get another
It's true, I replaced mine several times before going with Timken. Cheap only lasts 10k miles.
Especially if you press the new bearing back in using the inner race to press against, flat spots form on the races and balls?
Timken makes their shit in china and outsources to other brands, they have been advertising their chinese factory for years now. Last 3 bearings from Timken I have received were all bad right out of the box.
@@robsp32 Exactly, it's all about labor arbitrage and technology/knowhow. Our young guys don'thave a chance since our gov subsidizes this offshoring.
Use the outer race from the old bearing 😉 prefect size
This was always the scariest part for me. The shop I worked at had a press like that but with a gauge and when it kept climbing it was like in fucking das boot, waiting to die or lose an eye at least. The forces in play are crazy.
Oh man, you're not kidding. I had an old socket blow-- a shard from it flew out the back side, ricocheting from the floor, to the back wall, the off the ceiling and I don't know where it went after that. Initially I thought a bullet hit my shop. Rigging up a plexiglass shield is on my list.
@@jaykay8570 haven't you seen the hydraulic press channel his is encased in a plexiglass Guard I think.
Exactly...wondered why he wasn't wearing glasses/goggles..
Why didn't you use your red spray grease on the outside of the bearing before pressing it in. I just purchased the 3 can package from your SMA parts site, it works great. THANKS FRIEND
+Ronald Cach He said it was already really clean and greased up by the owner's work with it.
Love your videos! My first question ever. Here it goes and don't laugh at me. I removed a front wheel bearing on a 2004 Honda CRV for the first time. I watched videos on how to do it and that it was important to install the new bearing with the brown side to the back. My neighbor came over to see what I was doing at said that the brown side went to the front because the numbers go to the front. I looked at the bearing and looked the same both sides so we installed it with the brown side to the front and guess what after I finished installing everything and went for a test drive the stupid ABS light came on. RATS! My question: Can I press the bearing out and turn it around or do I just need to buy a new bearing? Thank you in advance.
Diana's World Of Fixing Things Sure you figured it out by now, but if not, I'd just bite the bullet and get a bearing. Your neighbor suffers from a common condition, where he believes his past application applies to all vehicles.
I've seen somebody use tranny fluid in a steering system because they must've seen it done on a Ford or something. In my old Taurus, you used trans fluid in the power steering, but it was not the same for the poor sap driving the Grand AM. This is where a manual can help guide you as you learn, and allow you to cross reference advice from lesser known youtubers, who might not be qualified (I've seen dangerous info on YT). It's not religion, but it'll help you on little specs like that, and I'd surely take it's word over your neighbor's next time 😕. On the bright side, you'll be a master on changing a Honda CRV bearing. .Have a beer 🍻