วีดีโอ

Finally got mine. This vid was helpful, I didn't realize I needed to calibrate the bed (it mentions upon loading it up to call them, but aint nobody got time for that...), so I did just autolevel and input shaper, not realizing that the bed calibrate was for the Z-offset. Wish they renamed it tbh. I'm coming from an OG Ender 3 "v1" that I've swapped to a direct drive, slapped a PEI bed onto, and converted to klipper along with a SKR mini E3 v3 board. Luckily I'm already somewhat familiar with Klipper. I just did my first layer print and it looks fabulous minus a tiny issue about the size of a golf ball where it looks like it wasn't quite close enough. Not sure how to address that yet. Don't know if I should try to up the flow rate just a tad, or maybe try to adjust the squish on that side a bit. Will probably try another layer again with PETG or ASA after a bit of adjustment and see how it goes. I don't think its the perfect "first machine" but I think its an amazing second machine for someone looking beyond the basic bitch PLA entry level printing. It offers just about everything I could want in a 3d printer that's under $1000 so far.

Siraya tech build in Smokey black has been hands down the best resin I’ve used. Too bad it didn’t make the list. It is slightly more expensive at $35/$40 for 1000g

I have had this printer for close to 2 months and there are some small issues true, but it’s a very reliable printer once you get through the teething issues. On the filament runout sensor it needs to be turned on in fluidd. Seems like it should be on by default but it’s not. Ever after talking to Qidi Tech support they never mentioned that to me. It’s in the setup section and it’s called “fila” right at the bottom of the page. Not sure if you have been told or not but just in case thought I would mention. The camera is a mystery to set up but I just set about the camera config file and activated almost all relating to web camera setting and both time lapse and app now work. I’m on iPhone iOS but I’m not sure how I did it to be honest. Again no one had that info from Qidi Tech. They are helpful in general but it’s early doors with this printer so maybe once they fully understand the setup themselves it will be less of an issue in the future.

I love my q1 pro prints so good but don't update klipper

Heat gun. Carefully get a corner going and then slowly roll it back while using a heat gun passing along the area you’re trying to peel away. Acrylic pressure sensitive adhesives hate two things: 180 degree peel forces and high temperatures.

I keep coming back to this review. Originally to help me decide which printer to buy, and now that I just received my Q1 Pro, for info on printing tips. I am amazed by the performance you got with TPU. I just looked at the stock TPU profile in QIDI Slicer 1.1.3 and it seems that the speed settings are the same for PLA. Did you use QIDI Slicer and/or adjust the TPU settings for the Toaster print. If so, would you share your info. Also, this is my first Klipper printer. I and I am sure many others could benefit from a short video on the QIDI Slicer and Its Klipper UI.

no need to apply gloop on the outer surface. thats just wasted material & the amount of product you put is ridiculous but if you’ee going for broke then you achieved it my friend. i tested the pla gloop on full size helmets and applying it on thin 2mm edge & just on the layer that gets into contact was already a solid connection that won’t fail unless its broken on purpose. once its connected, it literally melts and molecularly bonds so the excessive amount even on the outer surface was just wasting it but for a video i can see it was best case scenario. i just hope you’re not doing this to every part you want to glue together

You are my hero

they need better designers, looks like a coffin for a 3d printer

hey! subscribed!) what lsd printer do u use ?

Please make more Qidi Tech Q1 pro videos Please, maybe some about modifications

What is the smell of the resin during printing ? is it worse than sunlu standard ? better ?

Did u try the waterwashable from siraya tech ? if yes, what about the smell ?

If there is a perfect printer point me in the direction I'll take two please....................... This printer is the best bang for your buck on the market today right now thats not tiny AF. And that oozing in the front corner that doesn't happen with mine

I added the buildplate fix to my Q1 Pro. My Q1 Pro then started having the gremlins with probe samples exceed samples_tolerance error. I removed it and went back stock and it completely went away. I honestly have no clue what is happening. I have done 20 prints since going back to stock and haven't had the probe samples exceed samples_tolerance error a single time. Running V4.4.19

Can you give some details on the Bowden tube replacement? What size tube, how long, etc. This is my first 3d printer, so my knowledge base is bupkus.

Great news, smooth plates are going to be available soon!

My Q1 Pro arrived today. I will be setting it up tonite. I was on Qidi's site today and they had a smooth plate available.

Just ordered my Q1. Can’t wait to get it in.

Thanks good review, very informative. You mentioned oozing with TPU, but I don't recall any comments about printing TPU. I would appreciate your opinion on printing TPU, and any recommendations for printing.

k1 is v pooor printer...

Great review. I've had good luck with the run-out sensor working correctly. I just started printing with TPU, and it's been doing a great job. There were no issues with it spewing out filament while it was heating. However, the issue that I agree with you on is the timelapse issue. I cannot get that to work. I haven't reached out to support yet, but I will this weekend. Overall, this printer has been fantastic. I've had no issues with printing PLA, TPU, and ABS. This printer loves different materials.

thanks for the review, would it be possible to share the STL file for the riser

I replaced the nozzle with aliexpress hardened cht clone. Got a 33% flow increase.

Unfortunately DIY PERSPECTIVE just showed today that weight is not indicative of proper melting and adhesion drops way faster than flow

Bet it's really expensive.

Hi, I’m about to buy this printer (I can’t wait until Saturn 4 ultra shipping). Is there a way to fix Z axis flex/wobble with larger prints? Thank you

High quality review! My only suggestion would be safety glasses for that final bend/break test.

Thank you so much! I thought there was going to be cursing! lol. Very helpful!

Video idea - see if the Sunlu clear ABS-like is stronger than the grey or black. I ask because nearly all professional engineering resins are clear for two reasons. One is that pigments weaken them. Two is that they cannot cure as deeply.

Do you think it will be possible getting a review of the Wargamer by FauxHammer resin? I just found out the are selling it in the US now and it had my attention for a while for claiming to be the exact same quality as the manufactured minis you buy in store. I'm really curious how it will compares to actual store bought minis and the Jang He art-engineering resin that you sold me on.

Thank you

Great video

Very cool. I have a few of these delivering today. Any details/links for the wall mount?

How does the dryer pull moisture out of the box?

This is so amazing. What an outstanding idea.

Tempting to buy it

This is awesome

isnt speeds capped by firmware? idk just wondering