วีดีโอ

Thank you 😎

Do you still own this troublesome Range Rover sport? I’ve had mine for ten years and covered 131k miles, I love the car and wouldn’t swap it for anything ( can’t afford another or newer car tbh ) great video btw

Have to say I really admire your persistence. I have the exact same car on a 2008 and had the same issue basically gave to a trusted mechanic and he tested for leaks at the airbags and compressor etc and basically bought a new hitachi compressor (like for like) and job done all ok . Obviously you have a more complex issue …..great video and incredible amount of patience. Incidentally the new compressor was £600 but money well worth spending getting a proper decent replacement and not a cheaper replacement from eBay

the fkin car sux

You are using that tester in the wrong way!! Tha battery should be fully charged before you test it.

That’s an oil cula behind the front bumpa, love the British accent! Working on LR405 dat sht front suspension stays low🤬🤬🤬🤬

hi does any when know how can i refill the air suspension tank with air or one of the gases?

How do you convert from CCA to AH

Use jumper cables and it will do the trick and less chance of damaging the car. I like the battery tester.

Hi , I realise that you repaired your RRS sometime ago but can you remember how you removed the metal shield that is over the right hand rocker cover? I need to unplug the injector harness to remove the plenum. The four nuts on the bottom of the cover are the problem. I have tried to use a ¼” universal joint on a socket extension but there isn’t enough room to articulate the joint. The angle of the four nuts and closeness to the wheel arch makes it impossible to get a spanner on them. Any advice would be appreciated. Cheers Richard Adelaide, South Australia

I can't get mine to recharge any idea

Why would you waste your life on an MG, let alone a TF????🥱🥱🥱🥱🥱🥱🥱🥱🥱🥱🥱🥱🥱🥱🥱🥱🥱🥱🥱

Great work 👌 dont stress over the paint as silver is hard to blend and match.

I have been using the TOPDON, Antibattery 101 for years. It is easy to use and think its very good.

How to remove the back sub fram

How to remove the shockb

🎩

You ok ?? No more updates in a while pal

Resolution is … the new compressor needs to be coded to the car … needs ride height calibration too … need original JLR software to work on this

Bare metal the whole wing

Lol you never took battery off 😅😅😅 it first thing you should have been told also thinner rods and move faster you could arc it well onto next episode

Very helpful video. The camera angles were on point. Excellent video documentation. I learned a lot! What is the model of the OBD2 reader you used the most here?

Thanks man

As you'd pulled them valve blocks out shouldn't you of spent a few quid and refurbed them?

What was the main cause of your air suspension problem

Hi MG Lee, I hope you can help me!! I have a open Plug next to the Dip-Stick! do you know where it connects to? BR Pat with a MG TF 135

so wheres part 4....you cant leave me hanging like this ...im trying to get a RR soon,and you do this

"It's just not pretty...." Proceeds to show a really nice welding job..... Nice work mate... really good.

Sent message nearly a year ago. Looking for your resolution. ?

Heah man.. eaven with gas. It should be pok pok and done

u spend way to much time on 1 weldspot. Beter to have more power and spend a fraction of a second. Cuz more tim is more heat transfer.

I bought the Kingbolan BM550 on AliExpress however it didn't indicate any of my new or in service batteries as Good (yes I did set the tester to the CCR battery ratings). I tried to complain to the AliExpress seller, then AliExpress To no avail. I won't be buying from AliExpress again.

thank you, I always wanted an MG TF, it's such a pretty little car

You need to pull up your pants your buttcrack keeps showing

This car is trouble

It's 2024 so if anyone is watching this video you do not have to take off the front bumper you only have to take out the right headlight remove the cover that's in the right front wheel well for the supercharger cooler there are two screws that holds in the housing for the cooler and then you can access the part that you're trying to remove

I'd just spray over the lines where the masking tape was. That would make it look less obvious maybe?

When painting the panel I would probably of keyed the entire panel with a scotch pad, masked off just the door, window, bumper and boot. Then blended the silver paint out over the rest of the panel so you don't get a hard edge. Silver is a massive pain to blend as it is. Or do all the prep work, metal work and get a paint shop to spray just that panel.

Start by reading the instructions

I have the same rust/corroded area on my 2007 A6, I have looked at a load of “how to” videos and yours is certainly the one that is giving me the confidence to start cutting, shaping some sheet steel and make a new rear bit for it. Thank you and I hope mine turns out as well as yours does on the metal work/ welding. Dont worry about the paint. It protects at the end of the day

Hi excellent videos I have a MGF the clutch pedal has gone floppy any ideas thanks

Thanks so much for this great video. I had a PSACN error code and stuck on SRS light and feedback was "rotary coupler" - even though the horn was working. This helped me change it out on a 97 MGF. A few differences and I found I didn't need to remove the horn buttons just the connector. Super, super helpful! 👍

Hi from NZ please put me in the draw also are you returning the door panels card and all clips and stops etc going to have a crack at mine 😰

I have bm580, best and cheap analyser

Did you manage to start the car? What was the issue? 😮

Just found your channel, Great video'. I tried welding for the first time yesturday which was fun and in a few months I will be tackling the rusty sill on my Daewoo Lacceti. Keep up the good work.

Great Videos - Just discovered your videos in time for starting the compressor replacement myself (independent RR specialist replaced one last year but don't wanna pay their £150 per hour(plus tax) hourly rate and like most of my cars I figure once I have done it once it will be good experience should I need to do it again.

Na pohled z vrchu moc krásná práce.Co mi však chybí ten detail od spodku kde se spojuje práh s podlahou. Ještě dopilovat videika.👍

Supercharged