วีดีโอ

The rollers on the back of the mower deck. I can get them, but what about the shaft., what is the part number.

Have you tried Rust Convertor ?

at 23:37, where does that yellow/black wire connect? My fan broke and apparently took out that wire. I can't tell where to connect it back to? Would that wire being off cause there to be absolutely no power to the tractor from the battery? (no lights, no turn-over, nothing) I replaced the drive belt and wanted to move the tractor just far enough to see if I installed it correctly...was moving and tractor shut off completely in an instant......no sputtering, or idling down....running...then completely not. I'm guessing the fan cut what wire and it took out all electrical?

Dave, I'm having a hard time finding the right part (coil ignition replacement) for a old 2003 craftsman Briggs and Stratton 625 190cc 917 series push mower? Can I just get a coil that fits the screw holes? I'm a woman and have to do everything myself. Can you help explain if I can interchange the old coil with another Briggs and Stratton coil?

I have 2 fix mine

I would also like to see your friends video pleas send me a link

Don’t need a history lesson just get to work

Yes they growl I can confirm it too I heard that EXACT same noise

So, when are you going to show how to place the pulley belt on.

Okay spit it out get to the point

Thank you for answering my question about where the kill wire goes on the coil.👍

mine is all stuck in there and now I am just shredding it. crazy

th-cam.com/video/8Qa3m5mSZD0/w-d-xo.htmlsi=X9ZY9tuRRkCopSVZ Yardman!!!

Nice repair.

What goes bad in a hydro gear drives? I cleaned them sanded the revolvers and center secrion smooth..mower still fails on left side after 20 min. Also put in new center section and no resolve. Does the case wear out of spec?

WHAT SIZE TORX BIT OR ALLEN KEY DO YOU NEED TO REMOVE THE COIL. HOW DO I REINSTALL THE FLYWHEEL IF THE BRAKE ASSEMBLY WILL NOT MOVE DUE TO PROBLEM WITH BRACKET THAT CABLE IS ATTACHED TO BRACKET. I MOVED THIS ENGINE TO A CRAFTSMAN DECK AND THE HANDLE DOES NOT HAVE THE SAME HOLES FOR THE MOUNTING OF THE CABLE. ANY IDEAS?

I’ve been installing the older VS trans to replace plastic 💩, though it was a winter job and only took couple of days so I started doing it for the public 😊

i was able to replace the broken drive belt on my Husqvarna YTH22v42 no problem; thanks Dave for the step by step instructions

Mine was more difficult to diagnose as it only got stuck after the engine got hot. Of course one rarely uses the choke then. Havn't fixed it yet. The throttle shaft stuck last year and I had to ream out the corrosion from the aluminum housing with a drill bit and the shaft with emery paper. It uses a plastic sleeve as a bushing, so don't forget it.

I have one I'm willing to come off I'll send pics if u like

Where’s the video on taking it apart and filling it with grease?

I have a 18hp that’s red on a weedeater lawn tractor

Where can I get an air filter for this ?

A friend of mine who works on these, told me, he has fixed a number of failures caused by those caps cracking and spew fluid out. The fan blows it all around and makes a mess. The fluid gets low and the mower won't go. He replaced the cap, top of fluid, and they were back in business.

I paint mine. I bought mine used and painted the underside of the deck right away and now im preparing to paint the top side og the deck.

I actually got mine apart and put it back together and has been running for 3 seasons

thanks for this video! helped me fix my flywheel

The pan sealant you can use the silver from tuff torq or any RTV sealant, like blue or red, black. Must let dry partially to a skim coat then it’s ready to set the pan. Just for others FYI.

Do you know what size washer that you used on the axle

Tell me what the valve gap should be if you know

I have one, and I don't know what the valve clearances should be, if you know, please tell me

Awesome video man!! I just picked up an old gravely with the same motor in it, but its missing half the governor linkage and i have no idea what its supposed to look like! I have a feeling the governor quit working so they disconnected it. Is there any chance you have or would be willing to make a short video showing how the gov gets hooked up? You mention theres not many moving parts. If you end up changing yours i really hope you post up a video of the process!! I havent found hardly anyone working on one of these motors over my last couple weeks of researching it! Thanks again for the video man good job and thats an awesome run stand you built too!!

Obviously I hope my generator, that hasn't been started in over five years, starts like that, but in the meantime how do you move this sucker? The wheels are on the other side of the extended handle. I am really wondering how to roll this beast. Any help would be welcome.

I noticed your PTO lever spring is missing and the lever is loose. Mine is doing the same, and I believe it’s even missing the pin holding the spring to the body. Will that be a problem or should it be fixed?

😂😂😂had my step daughter freeze a Briggs like that,,,😂😂😂took abit to remove same problem then rebuilt 😂😂oven cleaner instead of lube oil😂😂😂

I just bought a cover comes with that bag

Bag for the cover

My stepfather bought this same exact model in 2018 at Lowe’s the serial number on the back states it’s a 2016 he only used it about five times before letting it sit in his garage for two years paying for landscaping because he has a bad back as of recently he gifted me the mower, but because it set so long, the carburetor needed work the fuel lines need a cleaning, spark plug needed changing. I took care of all of this for less than 100 bucks and had it up and running in two days it’s a great mower and now I’m actually excited for cutting the grass lol

Thank you so much for this video. I have been searching everywhere and this is the only video I can find that helps at all!

I've got 3 Kohler's with the magnets coming loose

I bought a Montgomery Wards (MTD) Signature 2000 with an 18hp Briggs engine that didn't run for $150 with a snow blower attached. I put a new carb with fuel pump, simpler wiring, and fresh gas. It purrs. I replaced the single stage blower with a near new 2 stage and did a multi coat paint job with more color on the tractor. After adding wheel weights and rear weights I may fill the tires with washer fluid. It's been a fun project and I can't wait for next years snow.

I have one just like it 42 inch deck 16 hp Briggs & Stratton engine. Do you know what year it would be a be around?

Is there a pin that goes in the piece the filter and spring are?

I have the same one that I am trying to get turned in

Thank you sir ! 😀

If I'd known what I know now. When I bought that junkquavarna. I'd have left it at Lowe's

I got a Husqvarna had a plastic cased junk General transmission, seals leaked all the oil out. Damaged the transmission, I'm gonna change it over to a hydrostatic transmission. Got a tuff torque hydro, in my Cub Cadet. Not 1 issue mower has 765 hrs on it.

Lookin for this to run my camper AC. I have a smaller inverter to run it when I need to be quiet. Think this will be a good one? I found it for $200 near me.

I take care of a fleet of commercial mowers that most are from 1998-2002. A few years ago I noticed rust was starting to get to some of them enough that I had to replace sections of the decks. I have a routine that once every 2 years they come to the shop for a complete going through and now part of that routine is the deck gets cleaned and painted underneath. I’ve been doing this for about 5 years now and so far it seems to have slowed the progress of the rust down. I do have some newer machines on the fleet and they are doing great with this routine. I do kind of wish I had the forethought to have started doing it sooner with the older machines. But until my company realizes my old machines need replacement I’ve got to do something to keep the danged things running.

Dave you gained a new sub