วีดีโอ

I know it an older video but word of suggestion, when you welding that close to a machined surface, your front ram, it's good practice to cover it to keep the weld spatter off of it. Your seals will thank you.

Dude use a shorter blade on your saw damn. Why make life harder.

Hi from San Diego Question, when you cut and change the exhaust pipes, it did show any engine light? Making that will pass smog check?

You needed to put a level on it

Is there any reason this could not be achieved with a 95 Rio Grande, 2.5L AX5? I need to replace my transmission crossmember and I will be welding on new frame brackets for the center. Just looking at mine and only looks like the exhaust might get in the way.

Your content is fantastic!Do you accept sponsor products?

Good ole budget Miller locker!

I thought you recessed your winch. I must have missed something.

Love your Jeep!

Love the build! Which leaf springs did you go with for front and rear? I’m doing the motobuilt stretch kits and love your jeep’s stance.

Great video! Had to do the same on our recent build. The fumes 😬😬😂 nice rig!

What amperage is channel 5 on your switch panel? 5a, 10a, 20a, or 30a? These instructions do not say how much amps/wattage it takes for the rock lights.

What amperage is channel 5 on your switch panel? 5a, 10a, 20a, or 30a? These instructions do not say how much amps/wattage it takes for the rock lights.

Wish patriot alliance was as still operating 😢

What a great build Jordan. You inspired me, moving the pump up and out, genius I say. I hope to see you on a trail!

What size pipe you use for the exhaust?

Beautiful truck buddy.

Damn that TJ has some GENIUS mods! 🙌

Good stuff 👍 honesty and humility make for a genuinely good video!

My buddy’s told me I couldn’t do this to my ecoboost because of the O2 sensors or something really confusing to see you just cut it off if that is tru

Great job! I’m going to be transplanting a 1963 Scout 80 onto a YJ frame. This kit addresses the the wheel base issue perfectly. Beats a cut/splice/ fish plating the frame.

man just found this channel by chance. i acquired a yj and was looking at a cage later down the road. i notice this video is 2yrs ago. anythings you wish you would have done diffrent on design now looking back? i really dig the look and want to mimic it

Nice work! Question what leafs are you using in the rear ? im thinking of also running that Motobilt gas tank , how do you like it .

Hopefully the side gears hold up!

Your locked and loaded now! Nice work buddy!

Nice job, love the rag trick to help dislodge a stubborn carrier.

Its not a limited slip, no slippage can occur with welded gears it just a lincoln locker

😂 Aaahh rags on fire! 😂

Bet that wont slip now. Good thing about the rag catching on fire is that the oil was burned off and it was preheated at the same time

Fellow YJ owner,do you know what brand of front bumper that is ? Great Jeep and video

Hi. Jeep is looking great question for you can you put a four point safety harness on your seats

Getting a yj in the next couple of weeks, and now I’m watching your videos and getting all sorts of ideas! Keep it up man, great stuff!

Lite brite

Have you trussed the front yet? Ive seen three jl rubicons break right at the FAD locally

Alright so have a question about the rear. I know in an old video you Said you where going move the rear hanger to be able to use the yj springs instead of the xj springs. Any cons on doing that instead of the xj's?

will a resonator delete pass inspection?

Nice to see you back on building the yj

Not a fan of your new rims & tires🤮

Great job, thanks for more ideas for mine!

Is that an internal or external slave cylinder? Ax15?

No im not OK I thought you crashed or something. scared the crap out of me. Great video👍

Reallly cool stuff!! I have been going back and forth on a switch panel….they seem to make things so much easier!!

Bro you need to do a video on wrapping it!

You should do a walk around of that Jeep.

what is the build specs of the new jeep? lift? tires? bumbers?

Curious to hear your thoughts after running it for a bit. was looking at the switch pro but might consider this for another project. Ps….my daughter made me watch the light show at the end twice 😂 Nice video as always.

The aux beam panel definitely makes everything easier and it’s more affordable 🤙🏻.

Well put together video. Great background music

So simple! I wish I could have bought something like that 25 years ago during my wheeling days. You should route all your auxiliary electrics through the panel (fan, ignition, winch, radio etc)

I love my Auxbeam switch panel. Works great. Love how you can program the strobe feature to the lights.