You need a way to read and write the nand, a glitch chip, and possibly a way to program your glitch chip. Reading and writing the nand is unavoidable, so if your Corona is a 4gb you'll need a tool like the "SD Tool" designed specifically for working with 4gb nands. If your Corona is a 16mb nand, you'll need a different tool like the Nand-X or JRProgrammer. For glitch chip I like the Ace V3 - and it has a bonus of coming pre-programmed. Lastly - some Coronas don't have an in-tact POST signal and therefore require a postfix adapter. Here's a link to a good video that will help you better identify your Corona: th-cam.com/video/X2HzIDWlH8k/w-d-xo.html
Hi i have have cotona v5 winbond i can’t boot xell with ace v3 i have question about the post fix is it all corona have the same value to test it or winbond is different ohm
just bought a matrix v1 of of the weekend modder and might buy a post fix adapter to all i can say is that the delivery is very fast and well package and he one of the best sellers i have seen keep up the good work
omgoodness glad i was sub to yah channel bro. bridging those 3 points made this corona i had show in jrunner. i was going crazy for 45 min b4 checking if u had a vid on maybe y n bingo u did when ubsaid i bridge these 3 points n it worked for me. that u sooooo much. love this channel
Hello, I just tried to boot my console with written ecc but my ace v5 does not flash and I got black screen instead of xell (as in around 34:30) as an output. Is it soldered wrong or am I missing something? Thanks for replies in advance. EDIT: Ace is after resoldering blinking green light but it does not have xell output, may HDMI be an issue?
It is definitely possible for Xell to boot but not display out via HDMI. If that was the case you would see the ROL (ring of light) still do the standard boot chasing lights animation. If you see this behavior, connect an Ethernet cable to the 360 and boot Xell and even though nothing displays via HDMI it will grab an IP on your network. I used my routers control panel to then discover the IP address assigned to the 360 and use Jrunners fetch CPU key via IP function.
@@TheWeekendModder Thanks, but I did not join the missing resistor solder points, instead I accidentaly desoldered them... I think I will lend it to professionals and see what will happen. Thanks in advance, I will definitely try it!
why do I allways get the message "wrong header" when reading the nand? I get a good flash config, then my jr programmer v2 reads the nand 2 times but crashes upon comparing them ? when I repeat it gives me "wrong header" error
I can’t seem to solder the r2c6 and r2c7 it doesn’t seem to stick to the pad and the solder wire leaves orange residue behind and the solder won’t stay on the pad and I accidentally unsolder some other pads i don’t know how to fix it because it won’t stay on the pad the pad I accidentally desoldered
I think I have the same board, corona v1, is it necessary to use the postfix? I am trying to do it with a matrix v3, and I am having some problem, especially lack of information of the welds .... And I think that I will need another alternative point for "rest" and "post"
TheWeekendModder OK thanks you are a great youtuber and I expect your subscriber as well as your business to grow drastically. Good luck in the near future
I'm having an issue getting mine to boot up. I believe I bridged the E and F resistor pads correctly. My chip is giving me 2 short beeps then 1 long run regardless of which timing file. If my chip is at least attempting to glitch does that mean E and F are right? I didn't check the serial, but my chip did have the sticker on the bottom with it so I assume it's genuine.
So, I modded my XBOX 360 and you left out a TON of info that someone would need to accomplish this. First there are 2 drivers needed to even get the programmer to work so Windows can connect to the device. One of those drivers requires you to turn of signature enforcement. You do need to bridge the 3 areas that you said you only do out of “habit” and not necessity. You MUST bridge those no matter what. Or, the XBOX will not display a picture after the install. You do not show where the wire goes on the back of the board. It is in your download package if you do a little digging. Also, you need to connect and ETHERNET cable to get the key to communicate between the programmer, pc and xbox. You can see it in your video but you never talk about it. All of these things can cause serious problems if you are unaware of them. Your package is great. You present incredibly well on video. You just leave out crucial info. The video would also be half as long if you just present the points instead of getting distracted. I love whet you have put together but it is flawed.
Hello, I just got no hdmi output at all after trying to boot to xell, may the unbridged areas be a problem? Ace v5 is blinking green, what got me unconscious because in the video it is red. You look like you had similar problems so I am just asking. Thanks in advance.
@@aaronfischer1836 well, I am calm now because I thought I screwed up or something :D. I will lend it to professionals and see, because i was not able to join those points. Thank you for your comment, it would probably help lots of people.
Thanks for the constructive feedback - people seemed to really like the live stream but I 100% agree with your point about getting distracted and the video getting longer because of it. As a small defense, I've got at least 3-5 other videos of this same process, and I cover every one of the items you mention in those other videos, but that doesn't help somebody who only watches this one. Again, thanks for the feedback, I'll do my best to incorporate it going forward.
What temperature do you set your iron to when you solder? Also the 2 points on the back do you recommend using a small tip on the iron? I don’t want to mess up the one very small one that I’ve heard other have lifted off the board
Hey bud i have a question and i know it an old videobut...... I have a Corona board with 4gb nand and i have to use the postfix(I have no traces by my CPU under the heatsink). what points do i attach to where after i install it? i ordered some V1 postfix and Ace V3.....
I just placed my order hope I got everything I need. For a corona 16mb nand no post fix.. I bought the nand x, ace v3, fiberglass pen, and some new paste..
hi, i got a Corona v5 with a acev5 chip and got boot to xell with no problem but cant get it to boot to dash updateflash.bin flashed on my console a get el red light after 6 blikin on the ace chip.Im using a postfix adapter any help will be thankful
Hi Weekend Modder. I followed the TX instructions for rev c and nand x. I was able to dump the nand, and write the ECC, but now I've got a red dot on the front button. I've reflashed original nand and removed all wires, but I'm still getting the red dot. Could it be the postfix? Also, I get around 100 when testing resistance between postfix and ground. Please help
When I have my MM set on it's 200K setting, I get a reading of usually right around 40-45. I've seen as low as 38 and as high as 52 and all was normal. All you can do is remove stuff and work backwards until you get retail booting again. And if you can't get retail booting - then you've killed the console. No reason it would ever boot RGH if you can't get it to boot retail.
I've double checked everything and the only anomaly is the resistance on the post out. I flashed back to retail and I will remove all nandx & rev c wires, again :-( Hopefully it works then. Any suggestion if it doesn't? Rawflasher? Thanks for all you do
1 other question, where should the CPU_RST and STBY_CLK cables be soldered? All the guides with rev c are on v1 or v2 Coronas which as completely different to mine (no, I don't have a Winchester mobo). Cheers
If you're using a Rev C on a Corona then STBY_CLK needs to be connected to something like a 48mhz crystal or a "corona upgrade QSB". You need a replacement STBY_CLK signal since there isn't one on the board to pull
I'm very late but I just ran into this last night. I fixed it but am still unable to boot. To fix the red dot, check those resistors, if you bridged the terminals horizontally by mistake this will happen. Unbridging them fixed the issue.
I am considering attempting this I have 250mb mfg 10 2012, I did check your website good info, so there is no way to tell if it needs postfix adapter without opening it?
hey weekendmodder, does the solder after the postfix adaptor installation (and multimeter test) necessary? i mean does it connects any needed connection for the point C? or its just to lock up the postfix? i burnt mine so bad i might solder it from underneath T___T...
Thanks for the excellent vids and putting all this info in the one place, awesome job. Can you tell me, do you have any plans on providing a download link for the Dashboards etc that you use at the end of this process? Thanks again
Evidently there was some sort of college football game released that requires a JTAG/RGH console so that's driven business up. I only sell supplies these days though and don't offer send in services any longer.
@@TheWeekendModder cool thanks man, im trying to figure a few of mine out, im familar with soldering an stuff just not sure been watching some of your videos to get an idea, most of mine are fine with drive firmware mod, but some need this
Is the postfix adapter bridge nessesary ? i've been trying for 4 hours and can't get it because it's in such an awkward position. The solder isn't sticking to the postfix.
No, you don't have to use those anchor points - they're only there to hold the postfix in place. You could got glue the postfix in place if that is easier for you.
what do you mean you bridged E&F so they can get their signal? I see nothing resembling that in the actual video. trying to install an ace v3 on a corona v3, please reply. thanks
i do see that but you say it isnt needed? should i just try it for my corona v3? because i have the postfix adapter and it isnt even trying to glitch like u know the fan speed difference between glitches? not happening. so try to bridge those 3 spots?
i got a corona 1.0 with a jr programmer and a x360 ace v3 chip and i was wondering what programs would i need besides jrunner and i want freestyle dash on it and i do have the file for that as well but i was wondering 1. how do you get it on the console(freestyle dash) and 2.where would i have to put the fr dash in order to get it to boot up to it( fr dash)
@@frankynakamoto2308 Why no one made it is because the Slim uses way less power and its adapter is rated at 135W while the least power hungry Fat (Jasper/Kronos) use 150W power supply. Other Fats use 175W or 203W.
Yo Aaron, quick question - how hot would you recommend running your soldering iron? I believe you said yourself you run your iron fairly hot as you work fast, but I'd rather leave my iron on the cooler side to give myself a greater margin of error and not overheat certain points and headers on the board.
Thanks! Oh and for reference, what times do you normally stream relative to your timezone? I think I'm in an unfortunate part of the world and unable to be here at a convenient time to when you stream.
When I press IP on jrunner it just gives me my cpu key and and then when I try to do the xebuild button after getting my CPU key it doesn't do anything is there any way to fix this? Like I get my CPU key and I press the xebuild it doesn't do anything I've been stuck for a week trying to rgh my Xbox trinity with ace v3 and nand-x and by the way I asked you about the trace repair about 2 weeks ago and I started using flux and it fixed it but it's delicate
If I unplug my console and plug it back in the eject buttons beeps but will not turn on console when pressed unless I press it like 30 times then it will finally power on console. But if you power it on then off with power button then the eject button will turn on console. Do you know what is up with it?
TheWeekendModder oh glad to hear that it's normal I bought a rgh for £50 but I decided to buy the equipment and rgh my friends one for him and it worked fine apart from that so I'm just happy to hear it's normal. Thanks again
hey can i ask a question im trying to rgh my corona 16 mb with ace v3 and i need the postfix adapter but when i try to bridge the points they are so small all 4 points just turn in to one ball of solder any tips like should i use different solder or something
TheWeekendModder okay so I put the postfix adapter on and everything. I hooked back up my console like put the power cord in and not the chip is green and red. I read the nands again and it says they're the same but under that it says the headers are wrong so what do I need to do? The one wire in the back was difficult to do and I'm pretty sure it's connected to two. Is that the problem? Hope you reply really wanting this done soon been working on it for like two weeks
liked this video too just wanna see you put a Ace v3 on a falcon or jasper just because i cant find a video showing this to check connections or timing files
Not sure you will see this I’m new was gonna do my halo teach edition trinity but grabbed a corona v2 just like this one so I can follow the video When I order my jr programmer is that how I get the software window that reads and writes the nand
TheWeekendModder did not expect you to respond while I’m still watching this video thanks btw I’ll be ordering everything except my solder iron, solder wire and thermal paste from you I’m glad your store is still up and super excited to give this a go
Hey I've been digging around for a bit and now found out what kind of system I have, but I need some assistance. I would very much appreciate if you can contact me. And if possible I would be interested in paying you to put it all together
www.weekendmodder.com has all of my video guides broken down by motherboard type on the left hand menu. Falcon/Jasper/Trinity and Corona each have multiple install videos
If you've overwritten the default file, then I'd suggest to use one of the S-RGH2 timing files from 15432. If you have my jrunner download the path to it would be: \J-Runner v02 Beta (283) Core Pack\common\15432's timings\s-rgh2_v2\CORONA\best_timings\pack_1_best\xsvf gh2_cop_su_du_30_2----.xsvf
also i was gonna also comment on alot of videos you answer questions while your viewers are sitting here waiting on actual intel cant you make a private chat session for that there is plenty of free scripts for that kind of social net. Run a bbs for free its really easy live streams are not important we just want intel not bs about others problems etc.
the reason i gave a bad comment is because he was so focused on peoples questions he didnt even zoom in on the point when he flipped the board if you wanna answer questions do a live stream for questions your a great modder but you need to seperate questions from the task at hand and if your gonna take questions while doin this then make it about what your doin.
I have a Xbox 360 s i found out it's a Corona mother board . Is it more likely to be JTAG or rgh . If rgh is possible then what would I need to do. Help me....
Please list every tools i need to mod my corona xbox 360 slim.
You need a way to read and write the nand, a glitch chip, and possibly a way to program your glitch chip. Reading and writing the nand is unavoidable, so if your Corona is a 4gb you'll need a tool like the "SD Tool" designed specifically for working with 4gb nands. If your Corona is a 16mb nand, you'll need a different tool like the Nand-X or JRProgrammer. For glitch chip I like the Ace V3 - and it has a bonus of coming pre-programmed. Lastly - some Coronas don't have an in-tact POST signal and therefore require a postfix adapter. Here's a link to a good video that will help you better identify your Corona: th-cam.com/video/X2HzIDWlH8k/w-d-xo.html
Thank you for replying man. Helps a lot dude and thanks for the pin even tho i dont deserved it. Lmao. Ty
Hi i have have cotona v5 winbond i can’t boot xell with ace v3 i have question about the post fix is it all corona have the same value to test it or winbond is different ohm
just bought a matrix v1 of of the weekend modder and might buy a post fix adapter to all i can say is that the delivery is very fast and well package and he one of the best sellers i have seen keep up the good work
Thanks!
TheWeekendModder would you say it's easier to mod a 16 mb corona or 4 gb corona?
How i can use matrix nand flasher ?
I RGHed my Corona today and I'm absolutely loving it
omgoodness glad i was sub to yah channel bro. bridging those 3 points made this corona i had show in jrunner. i was going crazy for 45 min b4 checking if u had a vid on maybe y n bingo u did when ubsaid i bridge these 3 points n it worked for me. that u sooooo much. love this channel
Great streams here! I have learned a lot from your videos, If I ever run into issues I always pull your videos up to see what to do next. Keep it up!
Thanks for the kind words!
The first ORIGINAL 50 Blocks of Nand which we are replacing with XELL ECC, will they be present in Original Nand dump that we saved as backup?
Hello, thanks for the video! Will the ACE V3 work to S-RGH a Corona board with 16 Mb NAND and Postfix adapter?
Hello, I just tried to boot my console with written ecc but my ace v5 does not flash and I got black screen instead of xell (as in around 34:30) as an output. Is it soldered wrong or am I missing something? Thanks for replies in advance.
EDIT: Ace is after resoldering blinking green light but it does not have xell output, may HDMI be an issue?
It is definitely possible for Xell to boot but not display out via HDMI. If that was the case you would see the ROL (ring of light) still do the standard boot chasing lights animation. If you see this behavior, connect an Ethernet cable to the 360 and boot Xell and even though nothing displays via HDMI it will grab an IP on your network. I used my routers control panel to then discover the IP address assigned to the 360 and use Jrunners fetch CPU key via IP function.
@@TheWeekendModder Thanks, but I did not join the missing resistor solder points, instead I accidentaly desoldered them... I think I will lend it to professionals and see what will happen. Thanks in advance, I will definitely try it!
If console continuously glitches but never boots remember you have to bridge the points at the top of the motherboard as he shows at the very start
Hmm I believe I did but I'm still not getting a boot. I'll make a post to reddit after work.
@@shanez1215 since this post I have made a small business out of it and done almost 200 consoles so I'm happy to help out
why do I allways get the message "wrong header" when reading the nand? I get a good flash config, then my jr programmer v2 reads the nand 2 times but crashes upon comparing them ? when I repeat it gives me "wrong header" error
I can’t seem to solder the r2c6 and r2c7 it doesn’t seem to stick to the pad and the solder wire leaves orange residue behind and the solder won’t stay on the pad and I accidentally unsolder some other pads i don’t know how to fix it because it won’t stay on the pad the pad I accidentally desoldered
I think I have the same board, corona v1, is it necessary to use the postfix?
I am trying to do it with a matrix v3, and I am having some problem, especially lack of information of the welds .... And I think that I will need another alternative point for "rest" and "post"
The little thing made of the bunch of wires that you connected to the nandX; can i buy that off your website or is it DIY?
I sell both the nandx to nand wires and the nandx to CR programming wires on my site. www.store.weekendmodder.com
TheWeekendModder OK thanks you are a great youtuber and I expect your subscriber as well as your business to grow drastically. Good luck in the near future
I'm having an issue getting mine to boot up. I believe I bridged the E and F resistor pads correctly.
My chip is giving me 2 short beeps then 1 long run regardless of which timing file. If my chip is at least attempting to glitch does that mean E and F are right?
I didn't check the serial, but my chip did have the sticker on the bottom with it so I assume it's genuine.
Great video! Any chance you could include a full parts and tools list so that anyone could follow along?
Weekendmodder.com, under the guides section has what you need
TheWeekendModder Thank you! Placed an order earlier and it looks like I got everything I need for my 16mb corona!
So, I modded my XBOX 360 and you left out a TON of info that someone would need to accomplish this. First there are 2 drivers needed to even get the programmer to work so Windows can connect to the device. One of those drivers requires you to turn of signature enforcement. You do need to bridge the 3 areas that you said you only do out of “habit” and not necessity. You MUST bridge those no matter what. Or, the XBOX will not display a picture after the install. You do not show where the wire goes on the back of the board. It is in your download package if you do a little digging. Also, you need to connect and ETHERNET cable to get the key to communicate between the programmer, pc and xbox. You can see it in your video but you never talk about it. All of these things can cause serious problems if you are unaware of them.
Your package is great. You present incredibly well on video. You just leave out crucial info. The video would also be half as long if you just present the points instead of getting distracted. I love whet you have put together but it is flawed.
Hello, I just got no hdmi output at all after trying to boot to xell, may the unbridged areas be a problem? Ace v5 is blinking green, what got me unconscious because in the video it is red. You look like you had similar problems so I am just asking. Thanks in advance.
@@NajGame that was our exact problem. As soon as we bridged them Xell came right up.
@@aaronfischer1836 well, I am calm now because I thought I screwed up or something :D. I will lend it to professionals and see, because i was not able to join those points. Thank you for your comment, it would probably help lots of people.
Thanks for the constructive feedback - people seemed to really like the live stream but I 100% agree with your point about getting distracted and the video getting longer because of it.
As a small defense, I've got at least 3-5 other videos of this same process, and I cover every one of the items you mention in those other videos, but that doesn't help somebody who only watches this one.
Again, thanks for the feedback, I'll do my best to incorporate it going forward.
What temperature do you set your iron to when you solder? Also the 2 points on the back do you recommend using a small tip on the iron? I don’t want to mess up the one very small one that I’ve heard other have lifted off the board
400C. Yes, small tip.
Please also make a video on how to restore the RGH console back to the retail version by using the original Backup Nand dumps.
Hey bud i have a question and i know it an old videobut...... I have a Corona board with 4gb nand and i have to use the postfix(I have no traces by my CPU under the heatsink). what points do i attach to where after i install it? i ordered some V1 postfix and Ace V3.....
I just placed my order hope I got everything I need. For a corona 16mb nand no post fix.. I bought the nand x, ace v3, fiberglass pen, and some new paste..
hi, i got a Corona v5 with a acev5 chip and got boot to xell with no problem but cant get it to boot to dash updateflash.bin flashed on my console a get el red light after 6 blikin on the ace chip.Im using a postfix adapter any help will be thankful
Hi Weekend Modder.
I followed the TX instructions for rev c and nand x. I was able to dump the nand, and write the ECC, but now I've got a red dot on the front button. I've reflashed original nand and removed all wires, but I'm still getting the red dot. Could it be the postfix? Also, I get around 100 when testing resistance between postfix and ground.
Please help
When I have my MM set on it's 200K setting, I get a reading of usually right around 40-45. I've seen as low as 38 and as high as 52 and all was normal. All you can do is remove stuff and work backwards until you get retail booting again. And if you can't get retail booting - then you've killed the console. No reason it would ever boot RGH if you can't get it to boot retail.
I've double checked everything and the only anomaly is the resistance on the post out. I flashed back to retail and I will remove all nandx & rev c wires, again :-(
Hopefully it works then. Any suggestion if it doesn't? Rawflasher?
Thanks for all you do
1 other question, where should the CPU_RST and STBY_CLK cables be soldered? All the guides with rev c are on v1 or v2 Coronas which as completely different to mine (no, I don't have a Winchester mobo).
Cheers
If you're using a Rev C on a Corona then STBY_CLK needs to be connected to something like a 48mhz crystal or a "corona upgrade QSB". You need a replacement STBY_CLK signal since there isn't one on the board to pull
I'm very late but I just ran into this last night. I fixed it but am still unable to boot.
To fix the red dot, check those resistors, if you bridged the terminals horizontally by mistake this will happen. Unbridging them fixed the issue.
I am considering attempting this I have 250mb mfg 10 2012, I did check your website good info, so there is no way to tell if it needs postfix adapter without opening it?
hey weekendmodder, does the solder after the postfix adaptor installation (and multimeter test) necessary? i mean does it connects any needed connection for the point C? or its just to lock up the postfix? i burnt mine so bad i might solder it from underneath T___T...
Thanks for the excellent vids and putting all this info in the one place, awesome job.
Can you tell me, do you have any plans on providing a download link for the Dashboards etc that you use at the end of this process?
Thanks again
Already have, check my vid history for the "twm jrunner package"
Brilliant, many thanks. I will check that out tonight.
Keep up the good work!
hows biz been anyway, now a days, id imagine prolly much more customers then before
Evidently there was some sort of college football game released that requires a JTAG/RGH console so that's driven business up. I only sell supplies these days though and don't offer send in services any longer.
@@TheWeekendModder cool thanks man, im trying to figure a few of mine out, im familar with soldering an stuff just not sure been watching some of your videos to get an idea, most of mine are fine with drive firmware mod, but some need this
What if you dont used any type of program to read the nand?
Then it's not going to work...
Is the postfix adapter bridge nessesary ? i've been trying for 4 hours and can't get it because it's in such an awkward position. The solder isn't sticking to the postfix.
No, you don't have to use those anchor points - they're only there to hold the postfix in place. You could got glue the postfix in place if that is easier for you.
Oh okay thank you. Also, when I read my nand on JRunner, it shows Corona then Trinity. And when I tried the boot my consoe the ACE chip doesn't flash.
Can you show how to connect the jr programmer to a corona 16mb? Also do I have to put the drivers on the chip?
Have you made an install with the ace v4? With a dual nand setup. Sorry if this has been asked several times
what do you mean you bridged E&F so they can get their signal? I see nothing resembling that in the actual video. trying to install an ace v3 on a corona v3, please reply. thanks
You see nothing resembling that in the video? Did you maybe skip the first part? Start watching from 4:45
i do see that but you say it isnt needed? should i just try it for my corona v3? because i have the postfix adapter and it isnt even trying to glitch like u know the fan speed difference between glitches? not happening. so try to bridge those 3 spots?
dude that E F shit worked. i fucking love you and your videos. NO OTHER TUTORIALS HAD THAT!!!! #THEWEEKENDMODDER
Gonzo what was the problem before you bridged the points
i got a corona 1.0 with a jr programmer and a x360 ace v3 chip and i was wondering what programs would i need besides jrunner and i want freestyle dash on it and i do have the file for that as well but i was wondering 1. how do you get it on the console(freestyle dash) and 2.where would i have to put the fr dash in order to get it to boot up to it( fr dash)
i have a corona v3 and the rc10 is not bridged do i bridge it like yo said with other two
Will J-R programmer V2 will work for Trinity and Corona?
It'll work for all Trinities, and for 16mb nand Coronas. It will not work for 4gb Coronas.
TheWeekendModder
Can someone make an adapter so I can use the slim power supply into a classic original XBOX360
@@frankynakamoto2308 Why no one made it is because the Slim uses way less power and its adapter is rated at 135W while the least power hungry Fat (Jasper/Kronos) use 150W power supply. Other Fats use 175W or 203W.
Weekend modder do you sometimes get really wild and mod on a weekday?
Yo Aaron, quick question - how hot would you recommend running your soldering iron? I believe you said yourself you run your iron fairly hot as you work fast, but I'd rather leave my iron on the cooler side to give myself a greater margin of error and not overheat certain points and headers on the board.
I run 470C
Thanks! Oh and for reference, what times do you normally stream relative to your timezone? I think I'm in an unfortunate part of the world and unable to be here at a convenient time to when you stream.
Hey weekend modder, is it bad if a resistor is missing on R2C10 or can I just bridge it
When I press IP on jrunner it just gives me my cpu key and and then when I try to do the xebuild button after getting my CPU key it doesn't do anything is there any way to fix this? Like I get my CPU key and I press the xebuild it doesn't do anything I've been stuck for a week trying to rgh my Xbox trinity with ace v3 and nand-x and by the way I asked you about the trace repair about 2 weeks ago and I started using flux and it fixed it but it's delicate
Hey when you going to come back to start doing service on RGh ages
I hope to see you make more videos in the future. I don’t mean Xbox 360 in particular. Maybe we will find a way to spoof security in newer consoles.
i also cannot copy games with xex menu it starts to download and completes in about 5 seconds is it a back xex menu maybe?
Whats do you use for the end of your nand wires?
he uses legs off some resistors
I like how theres a COVID notice on the vid because the word "Corona" is in the title.
Yea, I don't see them as the creator - but I've gotten that comment quite a few times.
what kind of cable is used to connect jrunner v2 t to the computer
USB Mini
Hi, I always get 13.8 to 14K in the 200K range, same as the other people. Not sure why you are getting 45K in the same 200K measursing range
I'm using cheapo garbage harbor freight multi meters, could be their not accurate.
Why does my multimeter show 90omh, is that the reason why my console won't boot into xell?
Did you solve your Problem? Perhaps I got the same, the Multimeter shown above 80 ohm and I can't boot into Xell
hello TheWeekendModder can i do this tuto on xbox360 E corona 16mb ? thanks btw for the tutorial very helpful
ace v5 work with corona 16mb no postfix needed(those 2 resistor are in place)?
Yes, but the install method of the Ave V5 is not the same as the Ace V3. You'll want to follow the install diagram at x360ace.com if you get a V5.
is that matter to change LED light or just keep original LED?
Changing LEDs is just a cosmetic thing - it doesn't affect functionality at all.
Where was point D soldered to?
imgur.com/8ha2Sta
If I unplug my console and plug it back in the eject buttons beeps but will not turn on console when pressed unless I press it like 30 times then it will finally power on console. But if you power it on then off with power button then the eject button will turn on console. Do you know what is up with it?
That's normal for an RGH. Just boot it once via power button first, then eject power on works fine.
TheWeekendModder oh glad to hear that it's normal I bought a rgh for £50 but I decided to buy the equipment and rgh my friends one for him and it worked fine apart from that so I'm just happy to hear it's normal. Thanks again
is this the same process as the xbox 360 slim e corona 16mb
Hi, what you use temperature to solder in the xbox ? thx :-)
Is 60 watts
How much do you charge to mod a xbox 360 slim
Where do I get the gpu back plate pry bar. Like what is it called and where can I get it
Need to know soon thanks!
It's called the "xclamp removal tool" and you can buy one from my store when I re-open on July 10th.
hey can i ask a question im trying to rgh my corona 16 mb with ace v3 and i need the postfix adapter but when i try to bridge the points they are so small all 4 points just turn in to one ball of solder any tips like should i use different solder or something
TheWeekendModder okay so I put the postfix adapter on and everything. I hooked back up my console like put the power cord in and not the chip is green and red. I read the nands again and it says they're the same but under that it says the headers are wrong so what do I need to do? The one wire in the back was difficult to do and I'm pretty sure it's connected to two. Is that the problem? Hope you reply really wanting this done soon been working on it for like two weeks
TheWeekendModder did I put the post fix adapter on wrong? Is that it?
liked this video too
just wanna see you put a Ace v3 on a falcon or jasper just because i cant find a video showing this to check connections or timing files
Sorry, I don't use that install method so it is unlikely I'll ever doe a video on it.
TheWeekendModder Can you mod my xbox that has two hdmi ports?
You have a console with 2 HDMI ports? For real? Post a picture!
do you deliver to the UK?
Yes.
Can we get an up to date trinity install?
Here's 5: weekendmodder.com/TrinityRGH.html
Thanks, man! appreciate ya!
Not sure you will see this I’m new was gonna do my halo teach edition trinity but grabbed a corona v2 just like this one so I can follow the video
When I order my jr programmer is that how I get the software window that reads and writes the nand
Look back in my past videos for the "weekend modder jrunner " there is a download there
TheWeekendModder did not expect you to respond while I’m still watching this video thanks btw I’ll be ordering everything except my solder iron, solder wire and thermal paste from you I’m glad your store is still up and super excited to give this a go
@@JAWZphotography good luck!
TheWeekendModder thanks just pulled it apart it’s a V4 corona so this should be interesting 😂😂😂
Why you remove leds ?
To put in different color leds
Is modding for XBOX 360 E Corona 16mb Nand are the same
Yes.
Hey I've been digging around for a bit and now found out what kind of system I have, but I need some assistance. I would very much appreciate if you can contact me. And if possible I would be interested in paying you to put it all together
www.sendin.weekendmodder.com is the place to initiate that :-)
Alright will look into it and I was wondering if you can help me instal the chips I have absolutely everything I can't find the correct guide
www.weekendmodder.com has all of my video guides broken down by motherboard type on the left hand menu. Falcon/Jasper/Trinity and Corona each have multiple install videos
mine says device not found
when do the first step
How much do you charge for to rgh a trinity
$75. www.sendin.weekendmodder.com
TheWeekendModder I believe I have a trinity but thanks for the reply I'll start saving lol
Arthur Games Message me @newchampionmodz on instagram :)
got it bro! i got money from christmas too XD
Arthur Games alright cool :) just message me on instagram
can I do this for a xbox 360 e slime I have a 16mb v5
Jesus Lera yes
Is the ethernet cable going to the pc straight or in a usb switch???
Ethernet can plug into USB??? No, the ethernet cable runs to a switch on my desk, and the switch is on my LAN.
TheWeekendModder ok thx
how much with u mod my 360 slim for
www.sendin.weekendmodder.com
i checked it out 75$.. i have the slim s series 2010
but ive been wanting to do stuff like that my self i just dont know enough about it
michael carroll Message me on instagram @newchampionmodz 😁
Can u mod a Xbox 360 whith a cooleunner?
KeZa omg how old are u?
I mean Corona
ULTRA GAMER Corona
u accept PayPal ?
No.
kinq i accept paypal bro, Message me on instagram @newchampionmodz 😁
Damn wish you'd reply to comments 😔
hey dude I'm new to ur channel how much is it for you to rgh my 360?
www.sendin.weekendmodder.com
Willie Davidson Message me on instagram @newchampionmodz 😁
where is that ethernet cable going???
into a switch on the other side of my desk.
what switch?
What file should I program ace v3 for Corona v3?
I wouldn't program any timing file to an Ace if I was installing it in a Corona. The Ace comes pre-programmed with a Corona timing file.
but unfortunately I reprogram the chip because the console did not want to boot and now I do not know which file to use
If you've overwritten the default file, then I'd suggest to use one of the S-RGH2 timing files from 15432. If you have my jrunner download the path to it would be: \J-Runner v02 Beta (283) Core Pack\common\15432's timings\s-rgh2_v2\CORONA\best_timings\pack_1_best\xsvf
gh2_cop_su_du_30_2----.xsvf
also i was gonna also comment on alot of videos you answer questions while your viewers are sitting here waiting on actual intel cant you make a private chat session for that there is plenty of free scripts for that kind of social net. Run a bbs for free its really easy live streams are not important we just want intel not bs about others problems etc.
the reason i gave a bad comment is because he was so focused on peoples questions he didnt even zoom in on the point when he flipped the board if you wanna answer questions do a live stream for questions your a great modder but you need to seperate questions from the task at hand and if your gonna take questions while doin this then make it about what your doin.
That seems like fair feedback, I don't like the interruptions either. Maybe Q&A sessions should be separate from any sort of informative content.
I have a Xbox 360 s i found out it's a Corona mother board . Is it more likely to be JTAG or rgh . If rgh is possible then what would I need to do. Help me....
Coronas are never JTAG'able - only old phats could be JTAG, so it will 100% require RGH. weekendmodder.com/CoronaRGH.html