HOW TO INSTALL BM3 FLEX FUEL KIT FOR B58

แชร์
ฝัง
  • เผยแพร่เมื่อ 23 ก.พ. 2024
  • Flex Fuel Kit
    x-ph.com/ptf-bm3-flexfuel-kit/
    USE COUPON CODE “MALAYA” WHEN YOU SHOP AT EXTREME POWER HOUSE
    Flex Fuel Kit PDF Instructions: bit.ly/3cJniJH
    After doing some research on calculating E85 mixes, I was sold on the PRO TUNING FREAKS FLEX FUEL KIT. Calculating E mixes isn't that hard, but it definitely takes up some time and adds extra steps. Also, if I went with, let's say, an E30 tune without the flex fuel kit and I wanted to go back to 93... let’s say you didn’t calculate the mixture correctly this flexfuel kit will automatically adjust the tune to the correct amount of ethanol. Ain't nobody got time for that. LOL. This plug and play kit. Let me know if you all have any questions! Thanks for tuning in.
    The best dash camera on the market •BlackVue•
    blackvue.com/
    Coupon code •MALAYA•

ความคิดเห็น • 15

  • @chosyn187
    @chosyn187 2 หลายเดือนก่อน +1

    Seriously better DIY vid than provided by protuningfreaks and Kies.. bout to knock this out this weekend 🎉

    • @malayaf30
      @malayaf30  2 หลายเดือนก่อน +1

      Thank you so much!!! I hope it helped out out and good luck on installing it.
      They cut a lot of parts out so make the video shorter and easier to watch, my DIY videos always include every detail

    • @chosyn187
      @chosyn187 2 หลายเดือนก่อน

      @@malayaf30update* on the s55, with wiring, on the clip you pull out there are 2 black wire pin holders and 1 grey..slide grey off and onto the bm3 harness, then place into clip and reinstall. Other than that, everything else is the same and very straightforward. Car is running great so far. Thanks again for the great diy!

  • @erich1308
    @erich1308 4 หลายเดือนก่อน

    Excellent job!

  • @gabrielrodriguez-gm2gf
    @gabrielrodriguez-gm2gf 4 หลายเดือนก่อน +1

    🔥🔥🔥🔥

  • @remyF30
    @remyF30 2 หลายเดือนก่อน +1

    I just got the flex fuel kit and I did everything right the only thing is trying to fit the flex fuel inside the hat location

    • @malayaf30
      @malayaf30  2 หลายเดือนก่อน

      That’s probably the most difficult part

    • @remyF30
      @remyF30 2 หลายเดือนก่อน

      Oh and the back seat installation 😂

  • @scottmckinney6471
    @scottmckinney6471 2 หลายเดือนก่อน

    Great video. Im about to do this install over the weekend. After the install, what do you do with the tune? Just select multimap and it will auto tune for whats in the tank?

    • @malayaf30
      @malayaf30  2 หลายเดือนก่อน +1

      I have a custom tune, so I had to reach out to my tuner for him to make another custom map with flexfuel enabled. You could still check the fuel ethanol content to make sure it works.

    • @Everybodyshinetogether1
      @Everybodyshinetogether1 18 วันที่ผ่านมา

      @@malayaf30do u recommend the bm3 tune after installing this

  • @TanyaKharachikh
    @TanyaKharachikh 4 หลายเดือนก่อน

    ❤❤❤❤

  • @luffararnesugerkuk
    @luffararnesugerkuk 4 หลายเดือนก่อน

    Thanks, prefer a long dragged out video over any "hey I'm mr YT look at me skipping steps in search for dicks, ohh sorry meant clicks" while grossly skipping over any small but important part, patience is a virtue or so the saga goes.
    Watch until the end, worth it, thanks and appreciate it. Just weird that you still had such pressure built up on the low pressure side at the fuel hat location, you pulled the connector, started the car, ran until died??? Maybe I am missing something, I find it strange should it not be more or less drained at that point?
    I want to do engine bay to skip pulling trim, rear seat, perhaps change my mind and go this route anyway just sporadically I feel engine bay should be less work, as long as the grommet is there as advertised it's a short distance straight down to foot well.

    • @malayaf30
      @malayaf30  4 หลายเดือนก่อน

      Thank you so much ❤️❤️
      I hate watching videos of other TH-camrs and when they skip all the important steps and don’t explain how they did it!
      After I installed the flexfuel I figured out why there was so much pressure in the low pressure side, it’s because I had my keys in the car and it kept priming. That was my mistake I should’ve had my key out of the car or disconnected the battery before hand. We live and we learn