e36: RC Car Lighting Kit Review, PART 4 - "RC Car Flashing Light"
ฝัง
- เผยแพร่เมื่อ 17 ต.ค. 2016
- Thank you for watching my video!
Please visit my Shapeways Page below:
Shapeways: www.shapeways.com/shops/ampro
Please, visit my sites:
Facebook: / amproengineering
Instagram: / amproengineering
Many of my designs and threads can be located at
www.tamiyaclub.com/forum/index...
If you enjoy the music featured on my videos, please visit Blue Pinto’s official site here:
/ bluepinto
www.reverbnation.com/bluepinto
I always enjoy constructive criticism and would love to know what you think about my designs.
Please subscribe as I have hundreds of other upgrades for many, many other cars, rc cars, toys, and anything else that I think needs upgrading!
**I have no tolerance for disrespectful posts, foul language, cyber-bullying, sexism, homophobia, racism and anything else that has no place in society. This is a family friendly channel so I have soap next to me for every time I say a bad word. Any foul or abusive post will be removed and you will be reported to TH-cam.** - ภาพยนตร์และแอนิเมชัน
4 years later and you've helped an RC veteran find yet another awesome product. Found it on Ebay and immediately added it to my cart.
they're about $13 bucks now though..
Oh glad to hear it!
@@michaelhuber6405 very cheap
Just added to cart, looking forward to having a play
Awesome! I like them
Thanks man. Just ordered a set. Thanks for the great videos and reviews. Helped tremendously
I hope you like them!
Bought two of them can't wait to install them thanks again for your time and help.
Any time Jerry.
@@AMPROEngineering my steering signals worked fine but nothing on throttle and brake and reverse unless I go into the flashing modes.
Strangely I notice my internal board is installed flipped from yours..hmmm
Your review make me choose this one, Thanks and keep moving
Sure thing!
Awesome video! Just what I needed.. finally getting around to finishing off my tamiya lunchbox :)
Glad i could be of assistance!
I really enjoyed your review on the light setups. it gave me some insight on what to purchase next time.
Glad you like them. There are a lot of terrible ones available so it is hard to not get suckered in.
I agree.
Thank you for the review! This headlight issue has had me so frustrated over the last few years. Funny, I had just bought two of these and after the standard setup resulting in the same issue, I went searching for answers and came across your video review. Much appreciated!
Not a problem man. They are so irritating.
I have the same kit in one of my cars IV just finished but struggled to work out what the switches did but now it all makes sense thanks
Glad it works!
Thank you for taking the time to review this product! I just pulled the trigger on one of these thanks too it! Looks like the J7 & J8 would be good for using additional led's for under-body or something of that nature
Very true. I think you will like it. I have bought well over 20 of these!
I just got exactly this light unit in the mail this morning, and two hours later I found this review. I think I did choose the right one! Well worth the nine dollars spent! :)
Oh yeah it is!
Excellent advice. I am trying to “light up” my bullhead and the 4 forwards on mode will work perfectly. Thank you for your testing on the kits available!
Any time!
Now that I'm seeing this review, I'm glad I bought this LED kit as I bought four sets. Haven't used them yet but good to see they work well. Great videos, subscribed!
Glad you like it!
Watched this video (along with your other light controller ones) many times, but just now realized this was from 2016! Bought this kit on ebay after watching your video and its perfect for one of my applications. Thank you!
Yeah this is the one I use still. I am happy they are still around but they are the best ones for the $
Very Good!!! Thanks for all your time on this subject. Found this still on EBAY as "Rc Car Flashing light" for $13.99.
Any time!
Happy ending! :-) Or maybe the next one will change that ;-) Good run through/review.
LOL yeah...I did literally buy 10 more of these. I love it.
GOOD JOB. I have a couple of these sets and no instructions. Had em for a couple years and they were maddening. You saved the day. I can now install lights in my RGT Jeep crawler.
Seriously man, is it that hard to EXPLAIN how the product you make works? It is horrible that they do this! I am glad you appreciated it.
Glad I found this video, this unit is exactly what I was looking for. I've got one now so just have to fit it into the car :)
Glad I could help!
@@AMPROEngineering - The name of the company is 3Racing, it says it in the first paragraph on the back cover. On mine it is called Kosta but it is still the same unit. The ports are actually correctly numbered on mine :)
Thanks for this video series, it helped me pick the LED kit thats right for me, I was also struggling to find the perfect one and this is it! Also I used that moving forward led slot(J2) for my muffler backfire and it works for me great!!
Oh nice! I felt like I needed to do these since there was so little info on them. Glad it helped!
I just want to thank you for your reviews you make our job a lot easier ,i just order this one it's the best of them all , my needs are the same of yours thanks again.
Not a problem. It is awful how you can't tell anything about these on ebay.
Sure that how china / their suppliers do their stuff, barely give detailed description on products no one told me my own experience, if no one puts his review on internet ...then i have to go through your adventure lol
Yeah that was my thought. I just wish they would have good documentation on this stuff. I have to watch my own videos to figure out how to wire those things up!
xD lol !
Nice review thanks.
I found these on aliexpress called '3racing 12 led Multi-color Flashing Light System'
... in case those last 6 get bought!
Really? Wow thanks for that info. It is probably being made by an over seas CM (contract manufacturer) and then labeled with a brand when it get purchased whole sale. At least now I can us that to look it up!
Praveen Rao I got it for 9 DOLLARS
Thank you for the info! i was trying to find it on ebay
Thank you very much! 😍😁
I'm so glad you took the time to review all of these lighting kits. I got the one on this review, the RC Car Flashing Light from eBay and it works great. I'm still trying to figure out the best way to install them on my LaTrax Teton, but all the functionality is there, I just followed your vid and I didn't even have to figure out what the Chenglish said... lol
Haha, thanks Jorge. I had to do this since they gave me such frustration!
Yeah, I would have purchased 5 wrong kits before I bought this one. I for one really appreciate the time and money it took to do these reviews!
Just got one for 8$..looks like the exact same. Can't wait to get it in, love the tip for constant headlights.
Not a problem!
Found your video regarding this light set, it seems to be the only one I have actually seen that truly works after some tinkering!!!!! I have bought 4 different types working off the channel 3 from my DumboRC Controller however none of them work and or they are either on or off. I will purchase one of these and try it out. thank you
These controllers can be so hit or miss. This one here is the only one that I have had great luck with.
YESSSSSSSS JUST WHAT I NEEDED THANKYOU THANKYOU
Glad I could help!
I watched all of your light kit videos and want you to know I actually ordered each kit so I could follow along! 😆
I LOVE your videos and the time you took to figure out the features and how to get them to work.
The car I spent the most time "making pretty" is my TT-02 Motul Autech Gt-R R35. I even used Traxxas Ford GT rear lights to make my R35 taillights look accurate and used resistors to make them work correctly with this light kit. This light kit seemed to work the best and matched up approximately with the lights I wanted to use and how I wanted them to operate.
I ABSOLUTELY MUST THANK YOU "THAAANNNK YOU!" (you have been thanked, 😆)! Because I would have NEVER had the time to figure out all of these light kits and find the right one for each car. You made it possible for me to bring a level of realism to my cars I really wanted to see. Now i can drive my cars during cooler summer nights and look good doing it! Thanx again!!!!!!
Very cool! I bet it looks awesome. Is funny as I still use my own videos to figure out the kits as I install them to this day
Used in my komodo & scx10 xj. Works like a charm & yes they are 3racing, it says in the middle of a paragraph on the chinenglish instructions. Can't beat em for less than $15. The ones on my komodo are now about 2 years old so they hold up too!
Cool man thanks for the info!
Great Videos
Thank you!
Nice video this is the best led system, i wish mine works like this one
Yeah, I am tired of all the ones out there that make no mention of operation in their advertisements.
Well you just answered all my question with this video and help me on buying a correct working lights set for my tt02 delta! Thank you
This is by far one of the funniest and most entertaining reviews I’ve seen on utube.. I jus bought this light set for my cen racing F450 daulie which is wat I want the flashing lights for hauling.. too bad the lights don’t come wit a light bracket so wen u drill holes in the body they don’t jus dangle
haha thanks. Yeah this is an instance where you get what you pay for.
Love the videos keep up the good work and you just saved me $100 AND showed me a unit with more realistic turn signal timing and brake light behavior Sub for LIFE
Oh I am glad I was able to help! Were you going to get the Tamiya TLU01 & 02?
actually was originally looking at the Axial Night Vision System for $99.99 no offense to axial but WAY overpriced and overbuilt for my needs, thanks to you i found an affordable alternative. I bought 2 of the 12 led flashing system in case one burns out, and that still cost less than 1/3 of the axial unit, i want buy some retro Re-releases and with the cost of this kit i can light up all the RC's i want, if only my Tyco Turbo Hopper was hobby grade i would light it up as well but i will have to wait until i can get a Hornet Re-release so i won't feel bad about driving a classic around in the dirt and i won't have to chop up my beloved hopper
$99! Really? I looks like one of the kits I reviewed! Man that is pricey. Yeah the Hopper is hard car to cut up. I wont touch mine!
Hey there. I ordered one of these about three years ago and just now gonna use it. I did order 3 more. There do work the best.
I'm installing one of these and another controller in a new Hilux HighLift build. Gonna be cool.
Very good to hear! I really like them
bad ass light kit
It is a good one.
all these later from this video i have all my RC cars running on this kit and they all work perfect
Yeah this is my favorite "cheap" set. I think I have over 30 of them.
thanx..just what i needed found same kit on ebay £13 coming from china ..cant wait
It is a great controller. I think I have 20 or so of them installed and in use!
Got it, 3Racing LED light system! (@17:58) Thanks, some great modes!
Sure thing!
Mine just came today and I installed it watching this vid.Cool
Oh that's great! Glad it helped.
Great review!! =) Subscribed! :)
Thank you!
Thank you for that.
Sure thing!
I think you are as particular as I am. All I want is headlight,fog light ,turn signal ,brake and maybe a light bar. I have the light kit from part 1, but I might get this one now. Great video too
Thanks you. You would think what I am looking for is not that hard to find...
hi there, really enjoyed your lighting video's.
I thought I'd get myself a set of these lights, so I searched eBay, but to no avail, just couldn't find them. now at the minute I'm building a tamiya globe liner rig and I put all the bits and pieces in the box. RC4WD motor, bearings, extra gears to lock the diffs, off road tyres, light kit, servos etc. so I got her built, painted the body, lifted the light kit, and guess what, it's the rc car flashing light kit. lol I've had it for a year or more, go figure. the more I thought about it the more I laughed about it. my light kit doesn't have the dip switches and the box is blue. so gonna wire it up tomorrow.
well, great vids as usual, lookin forward to the next one. 😀 👍 👍
Wow really? How did it go for you?
AMPRO Engineering I ordered a couple of the light kits and because I'd watched all of your videos on the lights, it was really easy, I could have wired it up blindfolded. so thanks for your videos. 😀 👍 👍 👍
Well thank you. I watch mine too when I get stuck, haha!
AMPRO Engineering lol 😁
They are good just got them today they are excellent I wanna buy another for back up 😁😁
Cool! Glad you like it.
I'm liking this set, know you see it as annoying, but outer headlights ON then "high beams" kicking on at 40-50% throttle is a pretty cool option that can be made to happen in single or double light buckets.
Rc Car Flashing light. Sweet. Found one on Ebay $14.99 I recognized the packaging with the Rc car flashing light logo. But its name is actually the #R0250 kit.
Oh thank you for the info!
Luckily they sent me this unit instead of the set with only 1 set of headlights. Either would of been fine but nice to have extra set of BRIGHT headlights. Thanks for the video on these!
Oh good!
Exelente 👍
Thank you!
The flahing mode isn't a demo mode. It is if you are building a police car/snow plow/etc. That way you have the flashing warning lights. Which means, that is a really cool kit. I have some on the way. Thanks for sharing!
Oh that makes sense.
Wow. What a ride, just to get to something that makes sense. Lol. Thanks for the hard work!!!
No problem
Didn’t read through all the comments but this kit is on eBay for like $13 free shipping. Just search “RC car flashing light”. First one top of page. Great videos man.
Very nice! I have noticed that it comes and goes on eBay.
If the cable that the button is connected too is black and red the schematics are correct. If it is yellow and white shits in reverse and sketch but still works fine .
It is correctly installed and seems to make the headlights flash? It is always different.
Thank you for that amazing video, I just get the Tamiya Audi Quattro A2 that need 16 light to cover the need of the model. Height of those light are the front white lights. So my question is, can I add two more light in the empty J2 and J3? This way, I will have 4 lights always open in J7 and J8 and forward lights in J2 and J3?
That will solve the issue of missing light.
Thank you in advance.
I wish you could but this kit isn't powerful enough. I usually make my own light set for the head lights and marker lights. You can also check out my videos covering my trick RC. They have awesome sets that will do pretty much anything.
FYI it's work! I added two more LED and it work's fine at low price
It says in the documentation that it’s from “3racing.” It’s in the the first paragraph but not in bold or very clear. I just bought one myself and noticed it. Loved the video and it was very helpful. I hate that 50% brightness to full for headlights too!
Yeah I can't stand that.
I finished the install with this kit but have you found a way for the turn signals to stay bright as well as the running lights and the headlights? I would like to have all three bright at the front. Any info would be greatly appreciated. Cheers
Thank you for solving my problem of choosing this great light controller. I really appreciate it. But could you tell me if I can use this controller and LEDs when my HobbyWing 1080 ESC is set to 7,4V instead of 6V ?
Sure thing! I think it would work but honestly I have not tried that. 1.4V is not that much of a delta but I cannot say if that will work.
At the beginning of review; J2 w/ the throttle pos = NOS or turbo/rocket boost ;-) :-p
I found these a couple days ago on ebay by accident for about 10.98ish (was waiting to watch this vid) I will order 2 at least maybe 4 . I saved this vid for later so I don't have to get PO'd working with it when I install them,, thx again and let us know when you get the other one you found if it's different.
This one has had the best instructions so far. I know the others looked like I had no issues but that second one I reviewed makes me shout every time I use it. That is testament to how good this one it. Hope you like them!
I tried tamiya light kit and GT power Pro
Yeah i have that GT Power Pro. Returned it immediately. Ill have the video soon.
Nice video, i bought the same when i saw your video, but i have a problem now, when i adjust the steering trim to the middle, the right signal light flashing, even when the servo in the middle, any suggestion ?
Really? even in the middle? Wow, sadly no idea.
I have that exact problem on mine also, not sure how to alleviate this issue
Thanks for taking the time to review all these light kits. I was looking for this for a while and your video helped buy save money and time ! However in my case the reverse lights only switch on when I hit about 30% of the backward throttle. It is a bit annoying since it is not 100% realistic 😆 Do you have that as well ? Thanks !
Yes, usually this is a result of the trims being off-center. Make sure everything is in the center and that should do the trick. In some cases, I have seen issues with throttle reversal too but that has been dependent on the radio. I hope that helps!
@@AMPROEngineering thanks for your reply ! I tried to play with the trim with no luck. It is probably a problem with the radio than. Just to help others having the same issue, the radio am using is a Radiolink RC6GS v2. If you are using the same radio the light kit won’t work as expected. Thanks
Upgraded motor to Castle Sidewinder and lost brake and backup lights function. Is that something that can be remedied in the motor programming?
Man I wish I could help but I have no clue about motor programming. I think that it has more to do with the radio trims. Have you adjusted those? I know mine need to have adequate travel for them to work. 2.4GHz I assume?
Can you tell me what diameters the led lights are. I’m thought I heard somewhere they were 5mm for the large ones and 3mm for small ones. Thanks man
That is correct.
Great video! I ordered some after watching this video. One question though, how much voltage does your RC battery have? Cause the description for the lights says it has 4.8 - 6V input voltage and I got worried realizing I'll use these in an RC car with 7.4V battery.
The battery is not used to power this directly. It gets power from the receiver. They are between 5 and 6v
@@AMPROEngineering Cool! Nothing to worry now. Thanks for the info. Can't wait for mine to arrive!!!!
Did you try this KIT with 7,4V?
@@radieroslaw yeah, still working after almost a year
@@erikfernandez4494 Thank you.
I found them just ordered one too 😁 lots of scrolling
Oh good! Hope you like it!
I will once I get them lol and the. Watch your video again to have the correct setup
Hi my friend I got my light kit that you actually like in this video and you'll be happy to know that my numbers on the control unit are actually in the right configuration to the diagram I bought mine from AliExpress for $10 bucks
Oh good to hear!
@@AMPROEngineering thought you'd like to hear that the numbers are correct
The ones that come on when you give it half throttle or more might be for inside the exhaust tips...lol
That is the best idea ever....
Do you know if it's possible to use a 3ch transmitter and receiver to control the demo mode of a led system like this one?
Now there is a thought. Without testing it I just dont know.
Oh well ty for your answer
Would it be possible to make this light kit or the tamiya light kit wireless? Meaning can you make a video and make this possible? There are other videos where they solder positive and negative wires to the magnetic post of the rc car!!!
yeah you could but given the number of leads you would need (headlight, markers, parking, reverse, turn, etc) it would be a total mess on the body mounts but still a great idea.
Which one is better ? In this video or in E39 video that you make?
Well... I like both but I use lots of these
what is the best led you think. Thanks
This one for sure.
what type of replacement leds should i get 6v or 12v leds?
Neither. Most LED's are between 2 and 4v and need resistors to work with 5v and higher. You will need to measure the voltage and then use resistor to help burn off the extra. Check out e33 for what I am talking about.
Is it possible tu turn on blinker ligths all the time.. without stearing?
No you cannot with these.
I know this post is a few years old, I just purchased two of these kits, and put one in my Xmaxx, only function that works correctly is directionals. When i start plugging other lights in the module, my steering will twitch when I pull the throttle, can't get reverse lights and brake lights to function as intended no matter what I do?? I'm thinking maybe the 4s Xmaxx esc is too much for this little unit? I'm at a loss right now.
Hmmm...so check what the receiver output is. It should be a standard 6-7.2 v. If you swap them, does the same thing happen? If not, then maybe the unit is bad. I have had one (not this one but a similar one) not have working reverse lights. These are super cheap and sadly, commonplace for something at this price point.
Hi, I have a Jjrc q65 jeep, and I was thinking of putting this light kit on it. I can see it is using a splitter wire to connect with the steering and motor. However, I also want to put a dasmikro sound unit along with this light system. The sound unit also occupies the motor connection. Is it possible to get both these product fitted or I have to choose any one them?
Man...that’s a good question. I would assume that both will work but space is also a concern. I have never used a sound kit but this may be a good test
for this led kit do you need any other wires or plugs to make them work in a rc car/truck... or does it come with every thing you need?
It comes with everything fortunately.
@@AMPROEngineering that little groove doesn't allow the y splitter to plug into my Chanel one or two🤔
same lighting kit i have in my slash which i only drive at night, and since the truck lights are the only lights i have to see at night and i didn't car about backup lights, i mounted the 5mm backup led's in front and plugged them into one of the aux you turn on with the dip switches so all the white led's are pointing forward, unfortunately 2 of the whites are dim until you accelerate but since i'm almost always full throttle they only go dim when i start the slide into a corner then i'm full throttle again. the other nice thing about the kit is there's no blue led's, why someone want blue led's on a car in the first is a mystery to me.....
Man... those blue LED's...I have no idea
Those modes are for like police or ambulance types builds
Very good point.
@@AMPROEngineering keep up the good work. Love watching your reviews
Thanks man
Maybe thay stay on for a muffler smoke effect
That's as good a reason as any!
Hi mate. I can't find it on Ebay. Kindly, could you share the page?
Wish I could man, they come and go randomly. The sellers are super inconsistent.
hi AMPRO i know this kit says 2.4 ghz but do you think it will work with 27MHz/75MHz
great videos as well
Hmmmm, Both of the cars I have this on are 75mhz and seem to be fine but there are so many factors that could lead to issues. I don't know why that would matter unless the unit can omit noise that would interfere with the receiver on an AM unit? Wish I knew more about this. Hope I helped a little.
hi friend
i see u order
and will soon send u item out
have a good day:) this was the answer i got for asking if it worked on 27 or 75 heheheheh we will see if it works when it gets here an you did help a little thank
Well thanks. Let me know how it goes.
so how do you wire it if you have a BEC in line and you disconnected the power from the ESC ?
I'll be darned if i can get it to work
Wow that is a fantastic question. I've never run anything with a BEC and this lighting kit.
@@AMPROEngineering thanks going to try sending power from esc and disconnected it coming out going into the rec. and will be using old axial ESC vs using my Holmes Hobby lol will post to let you know
I bought this kit, works great on the bench but with the motor connected above 75% throttle it lights up like a christmas tree with everything on max brightness. Any idea how to solve that one?
Oh boy....well I can see that maybe the throttle is reversed so the brake and reverse lights would come on but you describe all the lights coming on. Likely it is a bad unit.
@@AMPROEngineering could it possibly be a reciever issue you reckon?. It all works fine with proper brake & reverse lights until the motor is under high load & then it all lights up, car drives fine mind you.
Can you send me the link where to buy this please? Thanks
search eBay item number 264941334858 . That is the seller I get mine from.
Kind of a dumb question but will this thing work if its put on it’s own battery to just have the running lights on? (I’ve been having it interfere with my esc and didn’t like it)
No not dumb at all. Technically yes but it would not get inputs (obviously) and you would need a 6V source to both the ch1 and ch2.
AMPRO Engineering AMPRO Engineering hey there just a follow up from my question and give to give you some information that might be helpful, after some tinkering I found out that plunging a 1.6v battery in backwards so that positive goes to positive and negative goes to the sensor wire will power the light up, just everything on full no blinkers or special effects, also it can do the same with plugging into a receivers accessory port if you have a male to male connector to connect it to receiver with the connection to the light controller backwards of course (also only using one of the included receiver spliters to go to ch1 and 2 on the controller)
How do you wire it for marker lights?
You have to make them yourself and then power them from a different power source. That is the failing that all of these kids have
Can I use a 7.2 volt battery pack with this light kit
No, this runs off the of receiver power. They usually output 5-6V or so. The receiver needs to be powered from a speed control that usually uses the 7.2V battery.
cool thats the unit i bought
Oh that's good!
I’m new at the r/c game and I bought this light kit for my 15 year old radio shack ford p/u it doesn’t appear to have any place to plug in this kit , can it be adapted to it or do I need to take it apart more. Can you help.
No it needs a receiver designed for hobby type RC's. Basically all of the electronics of the car need to be swapped out. Sorry man.
Thanks for your reply I greatly appreciate it. Is it possible to just wire the running lights by themselves without all the other stuff.
What voltage were you supplying to this? I found this kit on Alibaba but it does not state what voltage. Most of the kits are 0-6V which will not work for me.
These are plugged right into the receiver battery port. Therefore they are 5-6V. I have not seen one for an RC car application that runs a high voltage but there may be something out there.
I've just for the latest version of this light kit, and I am using it with Futaba R334SBS receiver and basically it doesn't work. I guess it's because the signal of the Futaba T-FHSS is so fast that it cannot be picked up by this kit. Any suggestions?
May have to do with the trims. If you have the rates too low then it's likely that this doesn't see the servo input.
Do you have a link to this light set? I think I found it on ebay.
Sorry man I do not. Ill try and look for it
@@AMPROEngineering Just received mine. It'll be going into a new body, Proline Z28 Camaro. Very cool for the money.Oh, it does work with Tamiya leds.
I wish you had links to these products
The links would last a matter of days. Ebay sellers change constantly. Nothing I can do about that.
I realize this is an older video and you may not read this, but I have bought 2 of these sets for my son's Rustler and my 4wd Slash VXL. I installed it on my son's Rustler and everything works great, however my slash has no brake lights or reverse lights. I switched controllers then y harnesses with same results. I came to the conclusion that my receiver is not sending throttle controls to engage lights. but my motor is still behaving normal with brakes and reverse features. Any suggestions on what I can do to get them to function properly? It does not appear that the light module is faulty due to it works in my son's Rustler as the first did. I have the tsm receiver, could that be messing with the controls? Any insight would be greatly appreciated thank you,
So these units are really, really cheaply made. That said, one of the most common issues I have seen is not with them but rather with the trims on the radios. If they are not centered for ch1 and 2 to start, they just wont work correctly. Start there but if they still wont work, try swapping them and see if they behave the same. As for the TSM, i have not tried them on that radio though as some point I should given I have 2 of them.
@@AMPROEngineering I have reset my throttle and steering zeroed out and same results. I even moved to headlights to the position that brightens when throttle is engaged and nothing happens. They remain dim under throttle and no brake lights. Sometimes the reverse, headlights and brake lights are all on bright so I believe that it is not getting the proper signals from the receiver. I just don't know how to fix it. It is still a cool light kit and I will just have to deal with the lights I do have working. It just has to be my receiver, I thank you for your fast response and insight on the issue. If you come across this issue again and find a solution please reach out to me with the resolution to this issue.
@@rabbitsrcs how's it going, buddy?
I have the same issue with my TRX4.
Brake and reverse functions won't work.
Lemme know if you found a solution to make it work.
@@descontracao6566 I have not figured it out honestly, have been working on some of my crawlers lately
Unfortunately I can't make the braking and reverse functions to work with my TRX4 truck.
Has anyone else gone through this?
Have you centered the trims? This is a big feature that is over looked. These need to have all trims as close to center as possible.
@@AMPROEngineering Yes, I have. didn't work though. Thanks anyway.
Hi,but I had a problem with such a kit, with full throttle, the right turn signal flashes - I can't understand what's the matter, the marriage?
Usually you need to set the radio trim to the center.
@@AMPROEngineering походу брак-умирает плата-я не один такой
can u plz link one kit. i want one for my crawler
I will try. Every time I do they change, haha! I am looking now and can't find any. Ill look harder when I am home and post if I do. These used to be all over the place.
😂 jeesh! finaly. bugs me out to when thing don't work like they should.
I know. That's why I have been buying them. I knew there had to be something good out there!
I actually received one of these units today. Everything is working,except the brakes. They are dimly lit,but when I hit the brake nothing happens. Can't get the reverse to work either. I adjusted trims,etc. Any ideas? If anybody has used this on the DumboRc with the X6FG receiver,Please let me know the outcome. Thanks
I always find that the trims need to be centered on the radio for these to work correctly.
@@AMPROEngineering That was the issue. I had to adjust the trim ever so slightly,then it worked.
Anyone know where they still sell these?
I think you can find them on ebay still.
I have this kit but I’m having trouble with the turn signal. One side is always flashing. Can’t get it to stop. Anyone have this problem?
You need to center the steering on the radio. Almost all of the trim needs to be done mechanically by adjusting the servo horn and tie rods.
I removed the steering servo horn, tried adjusting the trim until the lights work properly and then install the horn back on the servo while centering the steering. Now I have no trim adjusting capability. Perhaps there’s a compatibility issue between my equipment. I am using the Flysky fs-gt3c
Show
What is it you want to see?
Anybody have a link for this kit on ebay or alibaba or something? Thanks
They are hard to find since there is no brand to search. You sadly need to look at what the controller looks like and go from there. They do not make it easy.
ru.aliexpress.com/item/Wholesale-Free-shiping-12-LED-Flashing-Light-System-for-RC-Car-kit/1053811689.html?spm=a2g0s.9042311.0.0.7LjMRe&aff_platform=link-c-tool&cpt=1511562904996&sk=uR7uBY3Rz&aff_trace_key=00fc44be932142218570a827d69143f9-1511562904996-02295-uR7uBY3Rz&terminal_id=10eeec9bf4464c72ad3819fb7e77df67
could you post a link for this lighting kit ?
Well as of now, here is a link! I can't say how long it will last:
www.ebay.com/itm/311549378186?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
+AMPRO Engineering thanks.
free shipping even :)
+the village idiot oh.. over 18 Canadian. . curse my worthless dollar. ... so ya. yay for free shipping lol
Haha! Yes free shipping always helps!
Like Christmas tree
That's the truth!
Great video! Couldn’t figure out my kit until I saw your video 👌🏻