Hint: You can also take the case completely apart, because no rivets are being used anywhere. Thus installation becomes much easier (albeit still a bit complicated).
Could you clarify your build method if you build it that way? Any tips would help! Im super new with pc. So the tiny case space makes assembly hard. You recommend to just take the case apart. Does that mean I first assemble the motherboard on the case's bottom, connect the psu wires, and then connect the gpu with the riser? Lastly, install the walls around them and place the psu in the bracket? Is that the correct method?
Interested to know how this does with all fans pointing as exhaust so that you'll have a negative pressure system that sucks air from both sides and exhausts it out the top and bottom.
@@NectarGaming i think it's the one that has a type C connection in the front. Because i just ordered this one, and the description said it supports 67mm coolers. I noticed that when they have a type c then they're probably the newer version, but idk if this is true.
Yes it should be fine. What’s not fine is if your riser is lower generation than your motherboard and gpu. E.g Motherboard and gpu is gen 4 while riser is gen 3, then expect windows crash or no POST Motherboard and/or gpu is gen 3, then riser can be gen 3 or higher. Technically, pcie generations are backwards compatible. But the riser should keep up as the riser generation is not part of the equation thus the minor complication that your riser should be equal or higher. Anyway, again, for your case, it should be fine
Great vid, build ended up looking very nice. I'm considering getting this case, but I have a 66 mm cooler (noctua nh l12 ghost s1) which is just 1 mm over the maximum the manufacturer says. Do you think it would fit? I'm already using a sama im 01 case with is already small, but I want an even smaller one like this one.
Just make sure you get the 65mm cpu cooler clearance version. This here only has 60mm cpu cooler clearance. The cooler that I put had a total of 62mm... There was a slight bulge but manageable.
Hello, same build with S400 and Aorus B550i PRO AX, but i have issue with my nvme gen3 at the back of the motherboard, too close with the vram of my 3090 FE. Maybe high temps ? Any tips ?
If you are not yet sure if it is a heat concern, I suggest to make sure that it is the concern. Say, check the temps while playing, when idle, and when there is disk load. But if you do have temp issues, maybe there are low profile heatsinks that can be attached to nvme drives (similar to corsair mp600 lpx nvme heatsinks) - i’m imagining it exists on amazon but sorry I just can’t confirm it now. It will not drastically cool it but at least there will be some heat dissipation.
did you try S300? curious how much worse it is temp/ventilation-wise also, i think the brand name is "shiny snake" as they have lil snake on their taobao store logo xd
@@daesz I haven't held the S300, but I just got hold of both the white and black S400 and they're gorgeous. Beautiful size, and that extra cooling, GPU and fan capacity go such a long way to improve the temps and fan noise of the system. I wouldn't downsize to S300 for the sake of a couple cm size difference.
may question lang ako hindi ba compatible ang IS-55 sa Gigabyte B550I Aorus Pro AX? parang compatible naman sila sa pcpartpicker di ba siya kasya ang configuration niya sa case nato?
Compatible po in 1 direction. Naka-usli yung heatsink pataas. With that, di kakasya sa case na to since walang space sa baba (since irorotate yung mobo)
Boss magandang araw. Pasensya sa abala. Ano pong ma irecommend nyo na case under 10L or under na magandang pang travel at pwede sa Ryzen 7 5700G na pwedeng lagyan ng GPU in the near future? Salamat
This case itself po -- s400. Though so far, I find ITX builds as space savers rather than portable / good for travel. Siguro dapat below 5L... Before, there was densium (5L case) with relatively good GPU support pero nagsara na. Maybe velka 3 if price is not an issue.
![[UNCUT] The Loyal Pin ปิ่นภักดิ์ EP.4 (4/4)](http://i.ytimg.com/vi/d3l5rxl5CVo/mqdefault.jpg)
Nice video! The month long wait is def worth it.
This is my favorite sandwich style ITX case within 11 L. Can fit high end GPUs no problem and can handle midrange CPU heat.
Hint: You can also take the case completely apart, because no rivets are being used anywhere. Thus installation becomes much easier (albeit still a bit complicated).
Could you clarify your build method if you build it that way? Any tips would help! Im super new with pc.
So the tiny case space makes assembly hard. You recommend to just take the case apart. Does that mean I first assemble the motherboard on the case's bottom, connect the psu wires, and then connect the gpu with the riser?
Lastly, install the walls around them and place the psu in the bracket? Is that the correct method?
Is albeit a real word?
@@deezllamas3907 ask google
@@deezllamas3907 Lil bro, may internet ka na. Isang simpleng google search makikita mo na yung sagot sa tanong mo 😭😭😭
Maganda talaga GPU compatibility ng case na to kaso yung temps talaga. Great content
Nice video manong.
CPU temps would probably better if undervolted.
Other than xmp, I test in vanilla for all cases.
more review kuys. 👌
Also known as: Miningeek Neo S400 (on Amazon Europe / Germany).
Can you fully disassemble this case? I'm interested on dissable capabilities for international travel.
Didn't really try but it seems like it. I didn't find rivets.
May nakapag build na dto using scythe big shuriken 3? 65mm kasi ung sa spec sheet pero 67mm ata height cooler.. plan ko sana lipat bahay pa-s400
Interested to know how this does with all fans pointing as exhaust so that you'll have a negative pressure system that sucks air from both sides and exhausts it out the top and bottom.
hi, sorry as I may not be able to get back to this case. Though it may help depending on the GPU. For the CPU, I don't think it will help that much.
will Thermalright AXP90-X47 Pure Copper fit into this case?
Yes. That’s 47mm, the case can fit up to 60mm, sometimes 65mm
There is a v2 of this case which fits 67mm coolers like the axp120.
could you link it or put the product name?
@@NectarGaming s400 v2
@@NectarGaming i think it's the one that has a type C connection in the front. Because i just ordered this one, and the description said it supports 67mm coolers. I noticed that when they have a type c then they're probably the newer version, but idk if this is true.
@@malealoy5622 one way to test this is to have a type c version then use a 65mm cooler
@@malealoy5622any update my friend? Did you fit the x67
The case you say comes with v4 PCIe riser. Can I use a v3 GPU with it? Say RTX 2070s. It is just a v3
Yes it should be fine.
What’s not fine is if your riser is lower generation than your motherboard and gpu.
E.g
Motherboard and gpu is gen 4 while riser is gen 3, then expect windows crash or no POST
Motherboard and/or gpu is gen 3, then riser can be gen 3 or higher.
Technically, pcie generations are backwards compatible. But the riser should keep up as the riser generation is not part of the equation thus the minor complication that your riser should be equal or higher.
Anyway, again, for your case, it should be fine
@@manongunboxing salamat!
Great vid, build ended up looking very nice. I'm considering getting this case, but I have a 66 mm cooler (noctua nh l12 ghost s1) which is just 1 mm over the maximum the manufacturer says. Do you think it would fit? I'm already using a sama im 01 case with is already small, but I want an even smaller one like this one.
Just make sure you get the 65mm cpu cooler clearance version. This here only has 60mm cpu cooler clearance. The cooler that I put had a total of 62mm... There was a slight bulge but manageable.
hello, can you remove the back panel to install graphic card?
If I understand your question correctly, the answer is yes.
All panels in S400 are screwed rather than riveted.
@@manongunboxing thank you
hi…what is the cooler fan size that you used on top?im planing to cut part of top to fit AIO cooler
It's a 120mm slim fan.
120x120x15mm
Overall cooler height was 62mm
Hello, same build with S400 and Aorus B550i PRO AX, but i have issue with my nvme gen3 at the back of the motherboard, too close with the vram of my 3090 FE. Maybe high temps ? Any tips ?
If you are not yet sure if it is a heat concern, I suggest to make sure that it is the concern. Say, check the temps while playing, when idle, and when there is disk load.
But if you do have temp issues, maybe there are low profile heatsinks that can be attached to nvme drives (similar to corsair mp600 lpx nvme heatsinks) - i’m imagining it exists on amazon but sorry I just can’t confirm it now. It will not drastically cool it but at least there will be some heat dissipation.
Di ba talaga kasya 120mm slim fan sa baba? Parang malaki naman yung space. Pwede din siguro tanggalin yung front usb if di naman need.
Kasya. It was part of the testing, may triple fan config.
Ordered this one. Hopefully the axp60x57 thermalright can fit. Btw what is your pcie riser? Will a 90 degrees riser be compatible with the case?
*axp90
Use dual reverse riser. 180 male and 180 female. This is the "common" riser for sandwich style cases.
@@manongunboxing thanks manong, last na ito how long is the pcie riser na gamit nyo for comparison lang cause amazon has great deals for this sff
185mm po.
@@manongunboxing maraming salamat manong!!!
Will this case fit an SFX-L PSU?
Yes, it will
did you try S300? curious how much worse it is temp/ventilation-wise
also, i think the brand name is "shiny snake" as they have lil snake on their taobao store logo xd
Video coming soon for s300
great, i really like it more than s400 (cuz its smaller), but i feel like it will be very hot inside due absence of 2 fans on top@@manongunboxing
@@daesz I haven't held the S300, but I just got hold of both the white and black S400 and they're gorgeous. Beautiful size, and that extra cooling, GPU and fan capacity go such a long way to improve the temps and fan noise of the system. I wouldn't downsize to S300 for the sake of a couple cm size difference.
Hey, how much space was left for the gpu after the installing the Strix 3070? I have a 4090 it’s a 8mm longer than the Strix. Thanks!
Iirc it was a cm more. But for 4090, beware of height as it might the 12vhpwr might hit the fans
Does the case have a glass panel for add on?
hi, I didn't see any glass panel add-on option.
did it come with the black fans or you bought that on your own?
I bough it separately
may question lang ako
hindi ba compatible ang IS-55 sa Gigabyte B550I Aorus Pro AX?
parang compatible naman sila sa pcpartpicker
di ba siya kasya ang configuration niya sa case nato?
Compatible po in 1 direction. Naka-usli yung heatsink pataas. With that, di kakasya sa case na to since walang space sa baba (since irorotate yung mobo)
@@manongunboxing ahhh i see ganun pala
thanks sa reply
Boss magandang araw. Pasensya sa abala. Ano pong ma irecommend nyo na case under 10L or under na magandang pang travel at pwede sa Ryzen 7 5700G na pwedeng lagyan ng GPU in the near future? Salamat
I mean under 15L at maganda ang airflow. Salamat
This case itself po -- s400. Though so far, I find ITX builds as space savers rather than portable / good for travel. Siguro dapat below 5L... Before, there was densium (5L case) with relatively good GPU support pero nagsara na. Maybe velka 3 if price is not an issue.
boss san ka nakabili ng case?
00:23 bossing :D Lazada and Shopee same shop.
I also added the links in the description
Does anyone feel like a slurpie?