You guys sell the diy solutions boot kit for this axle on your website, diy solutions is the original boot that toyota used, is there a way for me to buy your cv axle with the diy solutions boots installed on them? I keep going through the aftermarket axle because that inner boot keeps ripping
True, but this segment appears to be one of several videos where he is replacing multiple parts on the front end at the same time. We can see at the point when he is reassembling everything, we have a new axle, new seals, new wheel bearing, new brake caliper and rotor, new anti-sway bar link, and possibly a new spring, shock absorber, upper control arm, and upper ball joint. At one point, even the gravel shield disappears, so he’s gone ahead and removed that part, too. 🙂
35mm for the axle nut on mine. And the new ones were 35mm. Not 36mm.... so if u have to buy a socket, you might want to measure yours. But i dont think any of the fj's used a 36 for the axle nut.
If you're not getting a replacement part from A1, take your used part with you to the auto parts store as some available may have a smaller diameter shaft and not built Heavy Duty like the Original ones from the Factory.
⛔️WARNING!!! Do NOT remove the UCA castle nut before removing the nuts on the bottom of the knuckle if you aren’t using an air gun. You will loose all leverage and be totally stuck.
You're way better off just rebuilding/rebooting and regreasing the stock axles. I've gone through 3 different aftermarket CVs on my FJ. Toyota uses stronger steel than any aftermarket option.
It definitely looks like you had difficulty putting the new shaft in the differential. How long did it actually take? I’m having trouble with mine as well. Mine is an 08 tundra which looks very similar.
That internal clip from the internal axle splines that goes inside the differential seems really iffy to me. How does it not bend or break when pounding it in?
They are ALL like that. Every single manufacturer since CV axles were invented. Just the way it is! It's actually hard to remove it from the transmission.
I just want for my 2007 fj cruiser 2 Wheel drive to replace my original shocks for a better conforble Ride on regular roads. I was told Ranchos are good fit but I don't know which one for the front & back. What specific shocks,( i guess package or kit & comes with strats & spring coils) affordable purchase do you recommend ? Only the shocks?
Ahh yes the screw driver is the most misused tool in existence. A wedge, prybar, chisel, splitter, scraper, a electrical shorting stick, weapon, cleaning cobwebs, poking tight spaces, and lastly being a screw driver.
+Brian Morejon Thanks for checking us out! There may be a small amount of play to allow for movement but if it is leaking oil and a noticeable gap then that should not be like that. We wouldn't be able to diagnose an issue like that, you may want to have a local mechanic take a look at it. It may be there is something causing the new axles to not seat fully. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@@1AAuto thanks for the quick response! I ask because I notice once you had the axle inside you had the same amount of gap approximately so I’m just trying to determine whether there is something not letting it sit like you mentioned, or maybe it was just residual oil from the change making it’s way down.
+El Gato Gordo This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1AAuto.com
+El Gato Gordo We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
How did you access / remove the axle without removing the tie rod? Seems like you wouldn’t be able to get the shafts out of the knuckle or the diff. Doing mine this weekend. If I can eliminate steps it’d be great. I just replaced my tie rods, and I def don’t want to compromise them if I can avoid it.
We're always cycling through cars filming hundreds of common repairs for common vehicles every month. We'll add this to our list of repairs to film. Check back again and hopefully we'll have it soon. +Alejandro Figueiras
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
You guys sell the diy solutions boot kit for this axle on your website, diy solutions is the original boot that toyota used, is there a way for me to buy your cv axle with the diy solutions boots installed on them? I keep going through the aftermarket axle because that inner boot keeps ripping
You don't have to remove knuckle to remove the axle, just remove two bolts from lca and move it away
I did my FJ and didn’t remove half the stuff this guy did. Took me two hours. There’s better videos where you get the same results but in less time.
Hey Greg, do you mind linking which videos you are talking about? I have to do this to replace my boots soon. Thanks!
True, but this segment appears to be one of several videos where he is replacing multiple parts on the front end at the same time. We can see at the point when he is reassembling everything, we have a new axle, new seals, new wheel bearing, new brake caliper and rotor, new anti-sway bar link, and possibly a new spring, shock absorber, upper control arm, and upper ball joint. At one point, even the gravel shield disappears, so he’s gone ahead and removed that part, too. 🙂
Nice video, but my spindle nut was 35mm. Also, a sharpened flat blade or small sharp chisel will do a lot less damage to the dust cap.
They provide the torque specs - awesome.
35mm for the axle nut on mine. And the new ones were 35mm. Not 36mm.... so if u have to buy a socket, you might want to measure yours. But i dont think any of the fj's used a 36 for the axle nut.
Is yours newer I have an 08 so Idk which to buy
Mines an 07, my friend has a 2009 and his was also 35mm. Sorry for the late response.
If you're not getting a replacement part from A1, take your used part with you to the auto parts store as some available may have a smaller diameter shaft and not built Heavy Duty like the Original ones from the Factory.
Best film on axle swap ever. Thanks
⛔️WARNING!!! Do NOT remove the UCA castle nut before removing the nuts on the bottom of the knuckle if you aren’t using an air gun. You will loose all leverage and be totally stuck.
You're way better off just rebuilding/rebooting and regreasing the stock axles. I've gone through 3 different aftermarket CVs on my FJ. Toyota uses stronger steel than any aftermarket option.
Can you do a rear wheel bearing vdeo please. Thank you.
@8:13, just cringe when he pulls on the wire rather than the connector itself.
+risajajr Thanks for the tip! We'll pass this info along to our production team.
Don't wedge a pry bar in between the screws like he does at the 22min mark. You'll mar your threads and have to replace the stud.
It definitely looks like you had difficulty putting the new shaft in the differential. How long did it actually take? I’m having trouble with mine as well. Mine is an 08 tundra which looks very similar.
+HopsScotch The installation of the part will take about a hour. Thanks for checking us out!
Thanks for the video, super helpful man! Doing 3.5 Long Travel to SkyroninFJ and this will help a ton.
+valorboundwebstudios Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Brooo thanks so much... this video was so useful...
#1 video thanks for sharing..
Question.. what's the part number for the oil seal that sits in the clamshell where the new axle goes through..
Very nice video - thorough
That internal clip from the internal axle splines that goes inside the differential seems really iffy to me. How does it not bend or break when pounding it in?
They are ALL like that. Every single manufacturer since CV axles were invented. Just the way it is! It's actually hard to remove it from the transmission.
Nice work, are these 1AAuto parts 100% made & assembled in the USA? Do you have a branch in Canada by any chance? Thanks
I just want for my 2007 fj cruiser 2 Wheel drive to replace my original shocks for a better conforble
Ride on regular roads. I was told Ranchos are good fit but I don't know which one for the front & back. What specific shocks,( i guess package or kit & comes with strats & spring coils) affordable purchase do you recommend ? Only the shocks?
Is hookeydoo a technical term?
Ahh yes the screw driver is the most misused tool in existence. A wedge, prybar, chisel, splitter, scraper, a electrical shorting stick, weapon, cleaning cobwebs, poking tight spaces, and lastly being a screw driver.
Where can I buy some of the copper never seize?
Is it typical go have a gap after installing an aftermarket CV axle? I swapped both seals and axle and found some drips of oil and a gap.
+Brian Morejon Thanks for checking us out! There may be a small amount of play to allow for movement but if it is leaking oil and a noticeable gap then that should not be like that. We wouldn't be able to diagnose an issue like that, you may want to have a local mechanic take a look at it. It may be there is something causing the new axles to not seat fully. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
@@1AAuto thanks for the quick response! I ask because I notice once you had the axle inside you had the same amount of gap approximately so I’m just trying to determine whether there is something not letting it sit like you mentioned, or maybe it was just residual oil from the change making it’s way down.
Awesome video.
+Bruce Almighty Thanks for checking us out!
Dear god watching you tug on that ABS wire makes me cringe. Thank god this isn’t my vehicle.
Cool video 👍 Question, would this task be similar for a 2008 Tacoma 4x4? I have a split outer boot driver side that’ll need to be replaced...
+El Gato Gordo This procedure might be different for your application. We do not currently have a how-to video for this particular year, make and model. Thank you for asking! 1AAuto.com
+El Gato Gordo We don't have a how-to video for your vehicle right now, but the basic steps in this video should be enough to do this task. Buy this part for your vehicle on 1AAuto.com: 1aau.to/m/Shop-1AAuto-c
I didn't need to remove the caliper or the tie rod.... nice video though!
+Michael Williams Thanks for the feedback!
How did you access / remove the axle without removing the tie rod? Seems like you wouldn’t be able to get the shafts out of the knuckle or the diff. Doing mine this weekend. If I can eliminate steps it’d be great. I just replaced my tie rods, and I def don’t want to compromise them if I can avoid it.
Can you guys do a lower ball joint on a fj or a 2005 or newer Tacoma ?
We're always cycling through cars filming hundreds of common repairs for common vehicles every month. We'll add this to our list of repairs to film. Check back again and hopefully we'll have it soon. +Alejandro Figueiras
RIP tin boot caps as well
Nice job tho
Mrcc
But man oh man, guys if you’re a cotter pin; RUN
RIP all cotter pins in the filming of this video….
love toyotas...hate their front cv axles. Chevy uses a flange, swapped cv axles on that in 30 min. each side. tacoma takes a few hours.
Give it a loving bonk, easy peezy, you do you boo boo! Your too much bro 😂
+Joe Ray Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c