Avata 2 Full Power Unlock | FCC Hack / Mod | Speed, Response Comparison | Direct
ฝัง
- เผยแพร่เมื่อ 2 มิ.ย. 2024
- Feel free to skip ahead to 04:20 for the test!!!
00:00 What's the idea
01:34 Arriving at the spot
02:20 Gearing up
04:20 CE test (crash)
04:54 Some explanations
05:20 CE mode presentation (proper)
07:50 Setting up the FCC Hack
08:51 FCC mode extravaganza
13:29 End talk
14:41 Bonus - เกม
![ทททททททท #27 [หลุยส์ เค โตมายังไง ณ สระบุรี]](http://i.ytimg.com/vi/CaKoYw_Xmtg/mqdefault.jpg)
Finally, a proper test. Great job, man!
OMG, thank You so much
Cheers dude il try that on mine 😊👍🏻
Can you please tell if, besides the speed, the ham file also improves the communication range (quality of the signal) in the CE? Thank you. 😀
Does this hack work with the Motion Control 2 too? (at least for better distance range) or Just with the RC3 in manual Mode? Thanks a lot in advance
What firmware version do you have? Did you update the firmware before the hack?
Yes, I did update the firmware. And it still works.
geofencing is still active after this ?
08:10 after the first flight, do you need to keep the SD Card for the ham file hack to work? or its just a one time setup?
keep in most likely, im gonna assume removing it makes the goggles not read the ham file and thus default to original DJI settings
You don't have to keep SD Card with HAM file always inside. Googles remember this "hack". Only way to disable this is to hard reset googles
You dont need to keep it. As a matter of fact I put it in and turned on the goggles just to realize I didnt recorded the pre-hack CE flight. So I turned the goggles off without launching the drone, took the SD card out and then repowered goggles, drone and controller again.. aaaand the FCC hack was online (I hoped it was not), I already felt the power change. But for video coherence I didnt included this in-between footage. SO I had to reset my goggles there on the bench to get rid of the hack and do the CE flight correctly. Sorry for the confusion, I hope it makes sense.
I think you need to do it after each firmware update. I think it will be good to have small sd card staying in goggles with ham file or don't forget to check that mode after each update
It you first start up the drone, then controller, then goggles, it will be CE mode. First Googles means FCC mod. No need to hard reset
From the uk 👍👍
New sub
Ohh, sweet. I need to do more tests then xD
Thanks for the foam tipp lol
Haha, I knew people will find it helpful !! thx!
Are you from Poland? Do you registered your avata2 according to EASA?
Who the f cares
97? I could only managed to 82kmh ...! But I think fcc works anyway.?
Does the speed improve with motion controller as well?
No, motion controller speeds are the same in ce and fcc
dzieki ziomek
does anyone know if the DJI care is still active after uploading the ham file?
Would love to know that too!
so where is the code for the file or is it just an empty file named ham_cfg_support?
Just a empty file
Omg the bugs flying on you 😵💫😵💫😵💫😵💫
One of the worst feelings ive ever experienced is crashing your drone. I crashed my mavic 2 pro into a brick wall and somehow its ok lol
O I got it, you was dropping down, that's wat 97😂😂😂
I am from Greeece and the hack is not working...
format the sd card first.. and dont update
@@appslagu4704 thanks for the reply. I have the v01.00.0200 on the drone. Do you mean i should have not updated to this or after that?
Great video. Subscribe 👍❤
I did 21.22m/s (76.39 km/h) with Mini 2 SE. Released the sticks from the fear of breaking it apart in a wind gust against the drone 😀It's almost as fast as Avata 2 in CE mode.
How did you get it to fly this fast?
@@skylarblanton9677 ATTI mode
Вы русский?))
No, I'm not xD
DJi care is questionable at best. Within their policy clearly state repair of drone or replacement. When I broke the 'wrist ' on my Dji pro mini 4 which only had 2 hours flight time DJI does not repair your drone they replace it with another serviced one. I felt that's deceptive. Forced me to use my replacement option. They started that no repair get done only replaced with refurbished . I like DJI but not happy bout this.
Hi osce_zen, Can you create ham_cfg_support and use this in MOTION controller, aside from the remote controller, and what is the improvements, so is it faster now more than the 35 mph, thanks.
no
CE is restricting the output power just in the manual mode. Any other mode (normal, sport) regardless of the controller, are the same speed in FCC as well as in CE.
@oscr_zen another question, so in manual mode, is it faster can go 40..50 60mph, that I see in you tube flying with there avata2, so I have to create ham_cfg_support in sd card using manual mode in remote controller so it can go faster more than 40mph, thanks
@@sweetmosquite as I am showing in the video, get the ham file onto a card and put it inside the goggles, you'll notice if its working on the remote controller when the throttle power is substantially raised
When I create a ham-cfg_support in notepad when I put this in the sdcard, I have a videos in there now..is the sd card need to be empty no files in there at all before I put this, thanks
I can bet my arm and a fuckin leg you are z polski kolego 😂🫡👊