Dumbo RC Receiver and Speed Controller Setup and Fault Testing
ฝัง
- เผยแพร่เมื่อ 30 ม.ค. 2021
- A quick guide on troubleshooting faults with radio controlled cars, made using DumboRC ESC10A speed controller and X6FG receiver. The video covers checking components to fault find issues in your RC setup. Using a multi-meter to check receiver/transmitter paring and verifying receiver function.
- แนวปฏิบัติและการใช้ชีวิต
Very helpful, thank you!
Glad it was helpful!
thank you! this helped me confirm my transmitter and receiver are talking properly. now to figure out if the servo and esc are working
Glad it helped 🙂
Thank you for helping other..😊
Thanks for you nice comment, glad it was helpful
Great video, thank you for the thorough testing and the show/ talk of the equipment used.
Hi, thanks for the nice comment, I’m glad you found it helpful.
... Well done Mate, no info in the box about the receiver.
Thanks to you now knowing that Vcc & Gnd are all in parallel answers all my questions that not even the manufacturer divulges, (not intuitively anyway).
No problem, I had the same questions and found the info in the so called “manual” for the receiver a bit lacking. Glad it’s helped.
Thank you so much for this video. It helped me out
Thanks for your kind comment, I am glad to hear you found the video helpful :)
Thank you ❤❤❤
You're welcome 😊
Hi.
I was wondering if can you help me. I have a problem with my Dumborc x6 transmitter.
On channel 4 I have a winch motor, and when I turn off the transmitter (ch4 button is in the neutral position) my winch motor turns on and I can turn it off, only if I unplug the receiver form the power.
I have done some research online, and it seems to me that there is a failsafe on ch4 that activates when I turn the transmitter off, buy that failsafe is not setup to be in neutral position.
Do you know how could I solve this problem?
Thank you in advance.
what volt are the outputs from the receiver channels?
Thanks, now I understand.
Thanks for taking the time to comment, glad it was helpful.
is it possible to run a motor on channel 5?
My receiver works fine, well, lights and the stuff connected come on. The problem is the controller stopped working on its own within seconds. The blue light doesnt come on, seems the problem is inside the controller itself. Might that be there are some wires that came off inside the controller unit itself?
heyy... Great video, it's really hard to find videos that explain how these receivers work.
I'm making an electric go-cart as a project and was wondering if i could connect this receiver to something that powerful (500w-1000w). The usual throttles that are used to control the go-cart take a similar input of 6v so i thought this could work. They also have one negative, one positive and one control wire and output 0.8 to 5.3 v (no throttle to full throttle). Can you measure the voltage output range of the receiver? connect the negative pin of the receiver to the negative of the multimeter and the control pin to the positive of the multimeter and test voltage range with no throttle and full throttle. This would help me out a lottttt!!!! Hope you read this.
Hi, I’m on holiday at the moment, but can give it a go when I get back in a few days time.
@@randomdadstuff1777 Oh sure, no problem I'm just glad you read this comment. Great video btw ;)
@@randomdadstuff1777 heyya, just checking in to make sure you didn't forget.
Hi, apologies for the delay, have had a rather busy few weeks! The output range directly from the receiver was 0.15v throttle full forward and 0.39v full reverse neutral was 0.28v - quite a low voltage range for the signal. Hope that helps!
@@randomdadstuff1777 Yeahh... guess it won't be that easy. Anyway, thanks a bunch for helping me out, really appreciate it :D
i have a boat but got no power in servo or motor it wont do anything
Does this work for noble nb4 ?
Hi, I’m not too familiar with the Noble nb4, but having just looked it up it’s a nice bit of kit and the receiver should follow the same principles for the channels.
@@randomdadstuff1777 super happy w my NB4 & I’d highly recommend it.. I wasn’t prepared when I got into this hobby to spend over $500 on just the controller. So I didn’t & for $200 what I’ve personally experienced, it’s a no brainer. I think the best things aside from all the settings & options it affords you. I’d say is the pure comfort & something in your hand that feels well constructed. Just makes you want to go out & bash some more! I think it’s well worth it 💙👍
Bos ku, saya sedang bingung karena tiba2 lampu receiver saya mati, jadi remot ga mau konek. Banyak yang bilang kalau yang rusak antara ESC dan receiver.,
Tapi setelah saya cek pakai multi, dari ESC ada keluaran daya 5 volt, sebenarnya berapa daya yang di butuhkan untuk aktifkan receiver bos ku,..?
Mau jajan tapi masih galau, yang rusak ESC atau receiver.,
Saya pakai dumborc x6f bos ku.
Tolong jawabannya bos ku, share pengalaman buat newbie seperti saya
Hi, have you tried to test with the battery connected directly to the receiver unit without the ESC, do you get a light on the receiver? With the battery connected directly you should be able to pair the transmitter and then use a multi-meter to test for a change in voltage on the signal pin in the receiver, like in the video. This should confirm if the transmitter/receiver pair are working.
Terimakasih saudara telah memberikan jawaban untuk pertanyaan saya.
Saya sudah melakukan pengecekan seperti yang ada di video, menggunakan battery langsung tanpa ESC dengan tegangan 8 volt namun lampu indikator receiver tetap tidak menyala. Saya juga periksa tegangan di setiap Chanel dan mendapatkan tegangan yang sama.
Dari hasil pengecekan yang dilakukan, apakah receiver mengalami kerusakan??