Ebike S866 LCD Display Settings Parameters with Brainpower Controller
ฝัง
- เผยแพร่เมื่อ 5 ต.ค. 2024
- How to use and program your electric bicycle display computer
This is the instructions for a S866 LCD with P01 to P20 explained.
The display is compatible with 24v, 36v, 48v and 60v and has an optional front and back lights switch.
Common Error codes are:
Fault code | Fault status Remarks
0 normal status
1 Reserved
2 brake
3 Power sensor failure (ride sign)
4 6KM/H cruise
5 Real-time cruise
6 Battery undervoltage
7 Motor HALL failure
8 Turn/throttle gas handle fault
9 Controller failure
10 Communication reception failure
11 Communication failure
12 BMS communication failure
13 Headlight failure
#Ebike LCD-S866 手控面板使用说明
2019 最新版本-V1.0
![ลองสั่งของจากแอพ temu ถูกจริงหรอ?? ( part : 1/2 ) [โกงไหมครับ ep.89 ] | DOM](http://i.ytimg.com/vi/RTcZSQTiDZw/mqdefault.jpg)
P01....Brightness 1,2,3; P02....Km/m; P03....Voltage 32/48/60; P04....Sleep time minutes; P05....PAS mode; P06....Wheel size 26inch; P07....Magnet number in motor; P08....Speed limit; P09....Start level of PAS; P10....2=Peddle & throttle Assist; P11....Boost sensitivity=1; P12....Boost start strength; P13....Number of magnets; P14....Current limit in Amps; P15....Low Voltage power off; P16....Clear milometer; P17....Cruise enable/disable; P18....Speed ratio % adjustment; P19....1=Direct Hub 2=Gear Hub; P20....Protocol=0000
Another year has passed! Was out earlier and my bike stopped working, and showed E10 on the display. First thing that crossed my mind was " I know an easy way to find out what that means" 😁 Thanks yet again for a really useful video 👍
so what was he fix for communication problem?
@@racko6ix It was just a bad connection in the plug that goes to the display iirc.
Also had e10 error, changed p20 to 2, and all was ok. If you have this error just try all alternatives on p20
Turn on the display by holding power button for 2 seconds. Then press both the + and - button simultaneously. This will open to the settings menu. In the future it should open to the last setting you were working with. The numbers read P0 then 1,2,3, etc. The number 11-19 will read P1 then 1-9. There is only a P20 and a P21. Press the power button to advance through the numbers, the + and - to adjust the settings. Be careful, a lot of times when you depress the + and - key to go into the settings, it will raise or lower the setting it opens to by 1 increment. Just make sure to adjust it back.
01 LCD backlight brightness levels 1-3
02 Kilometers (1) or Miles (2)
03 Voltage setting for battery (24, 36, 48, 60v): under voltage is safe, over voltage bad.
04 Power saving mode turns off LCD after number of minutes. Set longer than traffic stops.
05 Number of PAS positions: 1-3 gears or 1-5 gears. These gears also affect throttle speed.
06 Wheel diameter: one of the only things measured in inches.
07 Number of speed magnets: Most 26” wheel conversion kits are 46 magnets.
08 Speed limit range: Why? So your PAS won’t kick on going down a 45 degree hill.
09 Zero Start: 1 Kicks on PAS when you start pedaling, 0 does not
10 Drive modes: Throttle, PAS, or Throttle and PAS.
11 Boost Sensitivity: Usually the higher the number, the more you pedal to kick PAS on
12 Boost start strength: Starts at gears 1-5
13 PAS magnet number: the little disk on the pedal, count the number of “dots”
14 Current limit value setting: 12A default with 1-20A range.
15 Undervoltage value: If Vs drop too low, batteries heat up, this number is cutoff.
16 ODO clear setting: just press + button for _____ seconds
17 Cruise control: 0 not enabled, 1 enabled, hold - key to turn on and off.
18 Display speed adjustment: adjust by % to fix speedometer when it is off
19 Gear enabled or disabled
20 Protocol numbers - Best to leave at 0, switches “interfaces” for different motor types.
@xenbot I have a 20" wheel. How many magnets is that?
xenbot, thank you so much! 👍
Hey man, mine does power on everytime I plug they battery. But I cant turn it off. Long pressing Power button does not work. Even the sleep time does not work. Any idea?
Do you know how to unlock the speed limit without a throttle? Its set speed in display, power off, then turn back on with both brakes and throttle full for 10 sec, right?
🎉😮😮😮😮 thanks for this information
Of a great help, I was about to recycle my e bike after buying numerous displays and not being able to fix it, nobody told me I hat to set it up, thanks a lot 🙏
Thank you because my bike came without a manual i APPRECIATE this😎
Thank you so much I bought this unit and lost instructions if it came with any. When I connected everything up nothing works now I can input the relevant data and hopefully it will work
Back again a year or so after I first found this video and it's still helping me out 😃!
This was very helpful. The S866 came with my 1500w brainpower controller. I used it to upgrade my razor E300 escooter. I connected it to a 6384 Brushless outrunner with hall sensors. It’s a Chain drive system. The controller runs it well. The gear ratio x number of magnets worked well to get my speedo correct. Only issue I have is it only works when the throttle is open. I installed the included wheel sensor to fix that. But it does not seem to send a reading to the display. If anyone knows a work around let me know. The wires seem correct. So I am stumped.
I want to reset my ebike fortis 3 to the factory reset, any help?
I love you so much ! You're my life saviour ! The battery was OK with 37 V on it but because the thing was set as a 60 V volt battery, it was not working ! THANK YOU
Just want to say thank you so very much for this very very helpful video thank you again
a GREAT VIDEO. SEEMS TO COVER EVERTHING VERY CLEARLY. THANKS.
Great thanks for the video. Able to adjust my new bike to mph 😁
This is a really helpful video!👍👍👍👍👍
Hello thank you for the video, I also have a 500W controller with an S830 LCD display. I have a 36V motor. after wiring the various cables, I still have the message E07. And also when I suddenly accelerate the driven wheel vibrates and stops. when I gradually accelerate no noise. So how do you correct your flaws?
Nb: my hall sensors, there are 5 wires, on the controller there are 6 wires. So I isolated the white wire.
My wheel is 350W / 36V
Thank you brother... it's a nice video... I installed a 48v 500w hub motor set on my 28" city bike... I set the p07 setting to 0001, then the km timer stopped working... I did some research and it shows the number of magnets in the motor, if it is not entered correctly. I learned that the km and distance would not be correct... Then, in the technical specifications of the engine, the magnet size was written as 27x2.3/27x3, so I entered the value 81 for testing purposes... The km meter started to work, but I did not know if it showed the speed and distance correctly... Can you help me on this issue? What should be the p07 value for my engine?
Hello I bought an S866 system and it gives me E10 error. Please can you tell me how to reset it and it works. Thanks
does anyone know how to keep this display from constantly reverting to all the default settings when your turn it off and turn it back on?
excellent video, thanks so much for doing this! I wanted to convert my 500w, 36v hub kit from a hand throttle/no lcd, to one with an lcd and thumb throttle. I purchased the Brainpower motor controller with the S866 lcd and still trying to get that to work, even after going thru all the P settings. I get the E 07 code, read that you can disconnect the Hall connector, did that but still show the error code . the controller is rate to 350w but my motor is 500w, so wondering if that is the key issue I'm having? any thoughts would be appreciated.
Hi, how to make shower Watt in LCD? Thanks
Press the power button briefly with the LCD already on, and watts will show where "TM" was. Press again for current.
Thank you very much!
hello i have a lankeleisi x3000 plus. the manufacturer says 46km / h but I'm stuck at 31 on the clock, 34 in reality. i try to remove the speed limit using the p08 which i put at 45 it doesn't change anything. i also have to modify the po7 but i'm not english i don't understand what to do. I am in the process of deregulating everything! if you could help me i would appreciate thanks to you
I have the same problem! any help? tks alote
Hi, I've tried to increase my speed. I already increased the speed on setting 8 to the maximum, what else do i need to make it go faster? Thanks
did you figure it out i’m trying to do the same
@@lil6io732 figured how to change it to 44 atleast yeah, not sure if there's suppose to be another setting to get the battery working st a higher voltage to match a faster speed
Ik probeer al een tijdje uit te zoeken hoe ik mijn lcd display s866 áán móét sluiten óp mijn controller en hoe ik de andere 2 draden verbind met de accu
Gracias! 🎉 pase de una velocidad de 25 kmh a 60 kmh 🎉🎉🎉🎉🎉🎉🎉
Hi, love your vid btw...could you help me where can i remove the speed limit off this😁
Thanks !!!
Someone is selling one locally for 10 bucks, after watching this video I'm buying it.
:)
Thanks for the information.
Hi I have the same display but unfortunately the parameter P08 (speed limit) flashes but pressing + or - does not change it how can I solve it ??
this is happening to me too , did you ever figure it out ??
Hi.if I set wheel diameter to 16" from 20" .would that change my speed ? Or just throw off actual mile readings? Love your vids.very clear and easy to follow along.thank you.be well.
No only the digits in the display but does not affect or boost the performance
My max speed was 20 and I wanted to see if I could unlock more. Now I'm stuck at 18 after installing display and I'm not sure how to fix it. It's very frustrating.
gracias !
What means P09?
P09: zero start, non-zero start setting, 0: zero start; 1: non-zero start;
I don`t understand that 😢
When you power on the assist level will be set to 1 if you want that or start with zero and you have to press the + button first after powering on
Hi
is there any way that the throttle becomes the walk assist function? for use the PAS usually
Push and hold the (-) button, it goes into 'Walk Mode". Be careful and ready, it goes until you push (-) again.
PLEASE HELP:
I know it can't be TWO Displays! I keep getting Error Code 10.
so motor won't spin | miscommunication btw display and controller.
two displays. two controllers. same error.
making things worse, I can't cycle through display parameters.
i can cycle to P0-8 but that's it then back to P0-1. No P1 (1-8), P2 (1-8), etc.
Please help.
Confused in Brooklyn.
Which PAS sensor fits, tried with 5 and with 12 magnets but did not work. in what position should P18 stand?
P18 only affects the speed on the display and not the real speed. Set P19 to zero enables PAS sensor
Hi..does this itme only works with lithium batteries...bcause when i use lead acid it be very fast to empty..
Hi. I have the error 07 on my bike... Everyhing seems to be ok BUT the error is there (the cabe hall cabel is connected). What is really the Hall sensor of the motor? What it is doing? Because I can't see what is wrong with the motor, it spins ok...
Mine is asking for a 4 digit code when I press + and - together?
Hallo! What does E10 mean? This error appears on my screen.
I have one of these LCD displays, if I press the minus button for a few seconds the motor switches on and runs at a constant speed but the throttle only works backwards and another long press or brake stops the motor, other than that the throttle does not work at all.
This work also with himo z16 bike display?
Does someone Knows hört to redet the Display the First settings
When I’m done with my settings, how do you save them. Once I turn off and then back on it loses all my settings
Please could you tell me the best settings to have with a 36v battery, it seems to switch off the lcd display and cut everything out when i use pedal assist on a hill even on a fully charged battery. The bike is only a few months old too.
Good explanation. Your Display shows E 07. do you know from where it comes from? I have a mystery on two bikes: Hall sensors 3 and the white are ok. but E 07 Can I reset the controller?
Hello friend, I have a question. I have the same controller and LCD screen on an electric scooter. I would like to know which of the p gets the maximum power amps, thanks.
Hello, it's P14. You have to set it to 20. You'll get 20A max.
can we connect it to hx scooter x7?
Hi there from the netherlands😇. I have an moovway fatbikw. With the same co troller. I walkwd true the menus and menu 7 says 25 km (i cant change that how can i manipulate that the bike goed about 45? Do i have to disxonnect somwthing in thw bike? Jooe to hear and thank you😇
What is the name of the connector with the red loop wire ?
Question: How can I set the PAS range from 15km/h to 25km/h please? The ADO A20+ offers only PAS in mode 1 with a 15 km/h limitation.
Please i have problem with my Bike, if i charge my Battery before driving to the next pole it will be showing me Battery low and it was full when i charge it i can't even drive to 3mins it will be showing low Battery Please how can i set it so that the battery will be lasting
I need to know the way to connect this controller with a manual throttle
P10 has to be set to 1 for the thumb throttle or 2 if you want to use both pedal assist and throttle or 0 for only pedal assist
The S866 Controller only goes up to P016. Is this a problem? (The sticker on the rear of the unit says 36V but my battery is 10AH 48v.)
Does the data need to be inputted like volts etc before it will work
Hello, I have this exact same controller on my Sparta ion GL. However I can't get it to work, I don't have any hall sensors connected so I get error 7, but it should not be a problem, because you have the same error. Can someone help me get my motor to spin at all?
You have to take out the controller inside the hub motor first to get it to work
I hope you can help me with my questions,
What are the standard 'settings' for this display when you boot for the first time ? I have changed a setting but i don't no what i have changed. How accurate must be the number of magnets for the hub motor ? I have a Sanyo Dynamo motor, but i don't know the ammount of magnets.
The number of magnets are not important and only affect the calculated speed in the display so any number works but lower it if the speed displayed is too low or increase when the display shows too much
@@diylifehackshobbychannel7609 I was thinking the speed come from the wire White and Braun connect to a bike speed sensor. (ILS)
I can't change the P0 8 speed limit its not changing is there any service protection to change the speed limit.How we can cancel it?
did you ever find out
hello i have a question any idea on why my 4 numbers on the bottom number is 5? and not 4?
hello do you have a wire colour video? I buy this with a kit from amazon but no info or wire map
Controller Comes with manual containing all param....?
Do you know what value P07 should be on for a 26” wheel. My speedo is about 3mph out. so when I’m doing 6mph it’s only showing 3mph. Thank you.
Hi just got one and the battery was full but I clicked options and now it shows as empty but it doesn’t work
hey how fast do u think i can go with a 350w 36v motor?
hello, how to activate the 6 km/h function on the s866 thank you
i just connected power 24V and motor on the controller , everythin is set to 24 v on the controller. i get errorcode 10, what to do. what am i doing wrong
What should I set for P14 Current limit value? I have a 300W hub motor and a 48V-10Ah battery (a DCH-015 battery for folding bike). Not sure what controller I have.
Battary has a 20A BMS
The pedal assistance no longer works for me, but the throttle thumb handle still works.
In the menu P10 I have set to 2 = mix, both pedal and throttle will work.
I have also tried option 1 & 0 in P10, but I cannot get the pedal assistance to work anymore. Do I sometimes have to set that elsewhere?
Incidentally, there is nowhere an option for default settings?
Check P19 must be set to zero (0=PAS, 1=No PAS)
If the pas used to work but now doesn't, I would think the problem lies with the pas itself and is nothing to do with the lcd settings. Broken or dirty sensor/ magnet disc? Distance between the disc & sensor too big? Or maybe a bad connection?
What does it mean I ride the bike by keep turning off
I have a 48v battery in 20 amp.
Hi can u help me i dont know what lcd i have, i have engwe ep-2, i change too much in the settings and the bike drive too much slower, how i can fix or rest it
I have the Same problem
they are fine. I went through the settings again and found setting, p20 value 0 to be a "settings reset" and value 1 to be Normal operation... I then found the connection fault gone for 0 and 1 but not 2 or 3 so 2 and 3 might be a different configuration... Had to plug in all my Values... the setting for P8 is a Guess the Default Value is 80 Magnet pieces... still did not figure out my accentual settings with out taking the Motor apart and counting the Rotor magnets and my back hub size is a tape measure guess is 27' but it seems to be working now, and the throttle seems to work too now.... go figure
I can't activate 6km mode or "walk mode" I hold the down button when still but nothing
You should see a walking figure icon next to the PAS level number after holding the button for 2 seconds or the walking figure disappears again after 2seconds and it only works when you are not moving so you have to push the bike a little
@@diylifehackshobbychannel7609
hello, would there be a way to activate the 6 km mode with a separate button? it would be useful for me thanks
I’m getting E11 what does this error mean?
Witam mam pytanie wymieniłem teraz sterownik na nowy s866 wraz z wyświetlaczem. Niby wszystko ok ale mam problem. Podczas pedałowania prędkość na wyświetlaczu pokazuje prawidłowo ale jak przestanę pedałować jadę na manetce prędkość spada do zera co może być przyczyną miał ktoś problem taki, i 2 rzecz po zaśnięciu wyświetlacza po paru minutach kasują mi się km przejechane i od zera rusza. Dziekuje
You have an error 7 on your display . What is the issue
Thanks
HEllo i found a problem when i press start i see by the km i need to film in a code
does anyone have manual for the brain power controller???
hi How to restart all setting ? go to "C1,2,3,4,,5" but how ?
why this display dont register the true trip in odometer . only register every 1km . If u do 900 meter and turn off the bike thats 0 in odometer .
Can anybody tell me where the other two wires the red and white go to is it small connector with a red and white and I can't figure out where they go to please help.
Is there any chance anybody has a default factory settings for the Geemax tricycle?
Can i also use a 52v battery on this screen?
im about to buy a 52 v and that display, do i set the controller to 48v? since it jumps from 48v to 60 ?
hi
i have always full power assistant .
can i change it with this display?
Check if you have P05 set to 1 or 2 and not zero
how reset it? to orginal setting
Hi,did someone manage to connect a light?on the wires I get about the same voltage as the battery,how can I connect 38v to a 4v led??
Use a resistor
what does wheel diameter stand for?
and what does these inches number mean?
Wheel diameter is the distance from top to bottom of your wheel and most common is 28inch
on my 866 I have only access to 9 settings . how can I get all 20 to show?
Same here. Do you know whats wrong already?
How to clear the E-07 error message.?
have a problem with this display when I turn on this screen appears with 4 0000 and I cannot make it work because I do not know the code can you help me please?
The default passcode is 3745 and I believe it only works when pressing and holding the power button for 10sec to unlock
unlocked lh100 by doing 0000 6666 3745 do I have to redo the same on this too?
lforgot my password how to unlock such a displey what can i do for help.
Ох и слепит подсветка ЖК в темноте, не правда ли? Рекомендую сделать светофильтр из отрезка чёрного женского чулка и, будет Вам счастье.
Hi- Good Evening! on my screen right next to Battery Sign shows up a ! E 10! waht does it mean!! Grootjes Johannes
dont know exactly... but i see in utube others. And they mean its an ERORR! But which error it is i dont know.
E10 is throttle is broke
does anyone have a printout of the wire connections for the 866c-6 controller with colors and designations? Thanks.
Red: Positive power
Black: Negative power, ground
Yellow: Power battery level
Blue: Signal sending
Green: Signal receiving
Brown-light: Positive power
, same voltage as battery
White-light: Negative power
ik krijg geen ondersteuning bij het fietsen daar ik wat met de instelling bezig ben geweest. weet iemand hoe ik dat weer goed kan krijgen? de eerste 2 dagen ging het goed.
Bro my meter show me E 10 what is this?
Have you ever tried a KT-LCD3 display/computer with the Brainpower motor controller?
If you have, which do you prefer...the LCD3 or the S866?
Does that change if you have tried any of the higher series of KT-LCD displays (e.g. LCD4, LCD8H, etc)?
Is this S866 display compatible with the KT controllers?
@@tofanalexander No. KT controllers only work with KT displays and speed/pas sensors.
@@Nitecrow314 do I need to fit PAS sensor for KT kit to spin the wheel or can old PAS work?
@@urbanpuma9136 You need a KT pas sensor, a regular one won't work with a KT controller.
Is it possible to get a link for the Brainpower controller with display?
Amazon, I Just Pick One Up , About To Test It.
@@r.vargas5410 Ya, but I can't find it. Can you link me please?
Hi friend do you know how I can fix Error 10?
The bike works, i go 20km/h and then release throttle, and once bike is stopped, error 10 is on and i cant use the throttle anymore?! :D
Difficult, sometimes set P20 to zero seems to work or if anything fails you need PAS sensor instead of throttle
Nice video, I have the same display wich give me error 10 and the brakes light is on. Do you know how to fix it?
did u fix it? i have same problem
@@FPSAnarchy nope mate. I got a refund from seller. That displays are faulty
@@vincenzotatti3325 how to buy this display
I have error 30, any one know what it is?
Useful but no clue as to how to set the time !!