KT LCD3 Programming - www.AffordableEBikes.ca Conversion Kits, works with LCD5 / LCD8
ฝัง
- เผยแพร่เมื่อ 30 พ.ย. 2024
- Here is a look at how to program your Display.
If you have a KT Controller, which is one of the most common in the ebike world, then you probably have seen these displays. They have a host of different parameters that can be programmed right from the display.
Cheat Sheet is at the beginning and end of the video but here are the parameters;
P SETTINGS
P1 = Magnets
P2 = speed sensor pulses per revolution (6 for Bafang , 1 for most)
P3 = 0 throttle is limited by gears, if 1 throttle is always full power available
P4 = 0 throttle always works, 1 throttle works only when pedalling
P5 = Battery Display - 36V = 12 , 48V = 15 , 52V = 22 , 0 for real-time voltage
C SETTINGS
C1 = 2 for Basic, 7 for Splined (KT-V12L) / 2pc Disc (KT-D12L)
C2 = Generally set to 0 (Motor phase)
C3 = Pedal Assist Level when you first turn on the bike
0 = defaults at 0
1 = defaults to 1, etc
8 = defaults to last setting before power down
C4 = 0 Throttle always working
1 Throttle by itself only 6km/hr
C5 = Current Control 10 for highest, 3 for lowest, 0 for soft start
C6 = Backlight adjustment
C7 = Cruise Control 0 is off, 1 is on, works by holding Up
C8 = Motor Temperature (if available)
C9 = Password
C10 = Return to defaults
C11 = Communication Protocol (restoring another display)
C12 = Low Voltage Cutoff (default 4) lower the number, lower the voltage cutoff
C13 = Regenerative Braking 0-5
C14 = Pedal Assist Overall Multiplier
Questions? Reach out! AffordableEBikes@gmail.com
www.AffordableEBikes.ca
Thanks for watching!
Thank you! I learned a few things with that walk-though explanation.
Great Tutorial for all the DIY out there
This is the most helpful video to mi Betsy, thanks a lot
Thanks for this.
Can I increase my speed from 15.5 mph to 20 mph? and how do I do it? Thanks
Thank you! What exactly does the password lock? the speed limit or the conroler itself?
Hi, do you have specific settings for BAFANG g020 500W (P and C settings), thanks!
Hello! Im in desperate need of help.
I purchased a KT controller that is 48v 45amps.
The problem im currently having is that. When i lift up the bike and MAX THROTTLE. It spins fast and fine
But where theres WEIGHT added like if im sitting on the bike. The controller cuts the power to my hub motor but the system stays on still.
Im not sure how to fix this
Hello, so if i have a 24 magnet direct drive motor do is set it to 46 or to the actual 24 magnets? Regards
There are quite a number of different aftermarket displays advertised, including the one your teaching how to program. What must I take into consideration when I am trying to get 3-4 miles an hour more on the top speed from a Magicycle Ocelot vs. a Himiway Cruiser?
Speed limit would be the main one , your bike could be governed. This will only apply to the KT Brand of LCD Displays
I think the settings are locked in setup mode so they can't be changed. What should I do?
Hi, i have the LCD3, how do you change the max speed for each of the levels 1 to 5 ? all my levels are at max top speed, like all my levels are like the level 5.
Throttle gears
Okay, can it be more explainatory please.Thanks@@ElectricBikeLaboratory
Yeah I'd like to have a max speed for each level, instead it just changes the amount of watts which isn't good for hill climbing. Can't figure it out so I just have to engage the throttle for now.
Hello thanks for the video its very informative i seem have changed the setting for voltage to 12 for my 36v buts its not registering after accepting the setting to 12 seems the battery indicater is still saying battery empty buts the battery is at 41v any thing I should try
Yes try spinning the wheel in the air with the throttle for like 10 seconds and it should reset
i got an s866 screen and an foc controller but seller told me its not intended for scooter motors and only for geard motors of ebikes ? can you help me plz ...
Hi how are things? How is it configured, so that each gear works from lowest to highest speed, what parameter is it? Example: 1 at 12km/h 2 at 19km/h 3 to 25km/h etc.... Thanks greetings.
Great video, I've turned my Cruise control on (C7 to 1) but mine won't Cruise control, it just turns the back light on when I long press the up button? Any ideas?
Hold the down button when your going about 12mph
@@olivergodlewski4864 Thanks, I'll give it a go and report back.
On mine it's 👇🏻 down
Hi, folks.. I'm in troubles.. I did adjustments like showed in this video, but display doesn't show speed.. I tried on 2 different e-bikes, one of them with direct drive motor and another with geared motor. First time I plugged display on bike with geared motor, I have speed working fine. First time I plugged the display LCD3 of the bike with geared motor on the one with direct drive motor, it also showed speed. This means speed sensor and data/communication display cables are working fine on both.
But, after configurations, 2 displays (LCD3 and LCD5) stops showing speed on first screen..
Any ideas?
P2 value usually needs to be 0 with direct drive and 1 or 6 with geared. If you set to 0 you should always get a speed value
@@ElectricBikeLaboratory Right.. I tried all options available.. P1 46 and P2 0.. After, I tried all options from 1 to 6.. Is there no other options involving speed?
I have the tk lcd3u, bought with the bike at the sport shop and I cannot enter the settings you mentioned at the start of the video (the one with pressing both buttons within 5 seconds), I can only reset kilometers I made. What am I doing wrong?
Have to turn on display and enter menu immediately. If you wait over 10 seconds it will only reset trip meter
@@ElectricBikeLaboratory I did, nothing happened, is it possible that the store the bike was sold to me could upload a software blockade, or custom software, or some physical blockade?
@@hufnaaratnaaf Yes that's definitely possible. Many of them are locked
@@ElectricBikeLaboratoryhey, I have the same problem. Is there anything I can do?
LCD81F how do you put the speed on every pass, like pass 1 it use 20% batt, pas 2 40% pas 3 60% pass 4 80% 5 100% ??? i can not find it anymoreq, i can not get into that mode again, can you help me ?
P3 and C4 are the main parameters
Are they the same for MXUS xf19r 1kw geared hub motor? Irony is even mxus themselves don't know how to tune setting correctly. I've got a lcd5 display
I'd think the 1kw main ones are P1 is 87 P2 is 1 . But I actually haven't tested on that motor quite yet !
first thank you very much I got my pas and speedometer working and set the current thanks to this video :D! second my display has a C15 and my google fu is failing me as I can't find anything about it any ideas?
My p5 doesn't go to 0 and it doesn't show the battery bar not even on 12 cause i got a 36v
It goes only to 1 on p5 not 00
My p5 goes only to 01 not 00 and it doesn't show the battery life not even on 12 for 36v
I have no response for the pedal assist. what do I do?
Hi, did you solve?
Hi. Can I do that with usb cable on PC, instead directly on LCD? Thanks
I don't believe so , the controllers themselves CAN be programmed from a computer but it's only if you hack into the system (google open-source kt controller endless sphere). Otherwise it is directly through the LCD
Thank u
I want to change the speed limit to 50 km/h (today it is 72 km/h) but I cannot change anything in the controller's settings.
What can I do?
That very first parameter you can change the speed limit
@@ElectricBikeLaboratory I got into the settings of the controller but I can't change anything (maybe it's locked from factory).
I even tried pressing the right and left brakes while changing settings, I can't change the settings and lower the maximum speed.
What can I do to lower the speed?
@@Or.H22 Maybe it is locked , there's not really an easy way to limit the speed if that is locked. You can try lowering the power level so that it can't reach a high top speed ? (C5 parameter = 3 is lowest setting)
@@ElectricBikeLaboratory thank you for helping me. I can’t change nothing in the settings.
Maybe I can to reset it but I couldn’t do it.
@@Or.H22 Some of them are unfortunately locked from the factory. It MAY be possible to get another LCD display that isn't locked but I can't confirm for sure
anyone happen to know what the function c15 is? I just bought this and saw it in there. Offers settings of 4, 5 and 6. no clue would love to know
Seems to be the speed of the walk function ! Hopefully this helps!
KT LCD11 is it the same setting...? I can't in the C1 setting...
They are all mostly the same but I haven't tried LCD11
i tried that kt3 with my e-scooter controller, it drives much better now but it does not show driving speed anymore.
Also i tried the other communication protocols and checked the hall sensor wires and everything is okay.
has anyone an idea how to fix that?
Try changing around the P2 Value , for a geared motor start with 1 , for a direct drive try 0 . Direct Drive is always 0 , but geared motors can vary between 1 and 6. Give that a try!
on P05 its not possible on my display it wont go lower than 1 i cant get 0
There are a lot of companies that factory order their LCDs and they lock several of the commands
I have lcd3 fitted can I upgrade to lcd5? Thanks
Yes
@@ElectricBikeLaboratory is it just plug and play? Or do you have to recode?
Thanks
You will likely have to reprogram a few things but nothing that should take more than 5 minutes
Does anybody know how to fix an lcd5 thats not showing current speed .
Same problem here did you figure it out?
@@Ashton._ono bud still trying to sort it .
@@kennyk4134 alright I’ll be taking mine into a bike shop for it tomorrow and I’ll ask him what the problem was and if u haven’t fixed it I’ll let u know
@@Ashton._ocool , cheers.
@@Ashton._ohi bud did you find out any useful info on the display from your bike shop.
tx 4u vid..its help me lot
You're welcome!! :)
How to Reset km? ODO
اتمنى وضع ترجمة الى العربية
Daripada lebih banyak korban ya berhenti saja gak usah diterusin perjalanannya....supir malah mikir dari pada banyak korban ya dibanting setir ke kanan
I have the controller shown on order think the controller had mode 2 on it . The motor i am using has no hall sensors , any idea on settings