ฝัง
- เผยแพร่เมื่อ 1 ก.พ. 2020
- Replacing front struts on 2014 and up Ram Promaster (Fiat Ducato, Peugeot Boxer, and Citroen Jumper). Can you hear a "popping" noise when turning the steering wheel? Then you need upper strut mounts!
The one and only Branick strut spring compressor -
amzn.to/2GJqOjQ
Upper strut mount Mopar right (always double check part number against your VIN!) -
ebay.us/bvMOvw
Left and right strut mounts - ebay.us/jpo91R
Pair of front struts (always double check part number against your VIN!) -
amzn.to/3ojp59a
Axle Nut (must replace) -
ebay.us/YB74db
If you make a purchase through these links I may earn a small fee at no cost to you. - ยานยนต์และพาหนะ
great vid!! and good work explaining!!
Great video! Just the information I needed. Thank you sir!
Thanks! That was the problem I was having, my ProMaster has 360k miles
good job
Thanks
Thank you my friend.😇
Whoever designed these vans and put the BCM there should be strung up!
Great video. I get the noise when I turn but also get clunking on bumps. Going to replace these mounts and hopefully that's it. Thanks for the video
Did that fix end up helping?
i have a similar problem with my promaster. did replacing the mounts work?
Is there a way to do maintenance on the strut bearings? Add grease ?
You mentioned 2 hours allowed for the job. Is that for 1 strut or both struts? What is a reasonable amount of time needed to replace a pair of these stunts and bearings from the time you start to the time you finish? Assuming you have the proper tools for the job. Looks like a fair amount of time and effort is expended to just get to them, then put everything back afterwards.
Een ganse dag heb ik nodig gehad. Bij hem is de aandrijfas eruit, bij mij niet; Bij een Ducato kan je de poot losmaken van de naaf, bij een Boxer met 1 schroef gaat dat niet. ik heb de 3 schroeven van de rotule en stuurarm moeten losmaken. Een ganse dag proberen was dat. Toplager en veer was gebroken, wat een rotklus.
Gabriel makes a strut kit that has a new spring installed plus that top bearing mount for $135.
Did you end up using that I see it on Amazon? But the problem is they say that they aren’t as good as the oem so it would be better to just get that top mopar piece to replace those ball bearings.
@@giannizamora7247 Replaced original with the Gabriel kit and after 12k miles I have a clunk coming from the strut tower. Not clunking while turning the wheel just when going slow over small bumps. Thought it was ball joint but the joint is tight can't emulate the noise when the car is jacked.
Is it necessary to remove axle from knuckle or did you do that for speed?
Nope, you do need to put a spring compressor on the quickstrut to install it without having to touch the balljoint or axle nut. I pulled out the sway bar nut to make things easier to put the control arm down to squeeze the compressed quick strut into the bore/ear on the spindle. 3 hr job.
why didn't you show how you put bottom back together
Don't we have to pump the strut before assembling it (mechanic has told me once) ?
I just checked the service procedure in FCA Service Library and there is no mentioning of ‘pumping’ before installation. The only ‘pumping’ required as far as I know is on Wranglers for steering dampener.
Was that 1st time they changed them, how many miles?
iceblue 69 Yes first time, 100k
@@TDRAuto Both of my front struts starting leaking oil at 75,000 I had Maxicare so they were replaced with new mounts also
4:54
Damn.. I thought I could change them on my own. Is to much work and I definitely don't have the appropriate tools.
2 hrs labor is ridiculous. Customers only see the total bill and have no idea how little of that actually goes to the tech.