Perfect video. I noticed the trailor brake wires on a used 16 ft trailor I purchased have been cut. So, I'll be replacing mine soon. Thanks for the tutorial.
The Lazy Lube system is the worst thing ever put on a travel trailer. Boat trailer okay. To much grease can cause churning in the bearings. Churning will generate heat. Trailer brake wiring must be connected with crimp on water tight connectors. Never use Scotch Locks. Bearings must have from .001 to .005 inches end play. Never preload a wheel bearing. All wear points on drum brakes must be lubricated at regular intervals.
Agreed. Cranking down on the bearing and calling it good is NOT the way to do it. Probably why dude had bearing issues. Preload your bearing, then loosen the nut...retighten finger tight. Done. I haul granite (12k+ lbs) and run 3000mi a week, never had a single issue with my bearings.
I’m surprised you don’t go through the process on how to properly torque the center nut. I can see someone inexperienced tightening the whack out of that nut and burning up there bearings.
what should the torque for the center nut be ? im currently replacing brakes on mine and when i unstalled it was so lose i didnt know if thats how they are supposed to be ?
I’ve always tightened the nut up as I’m spinning the drum in the opposite direction with a 1/2 drive ratchet. Snug it up tight then loosen about 1/4 turn, spin the drum again and retighten the nut. Back off about a 1/4 turn and install a new cotter key.
Good video, but one thing I would add is the scoring on the inside of the drum is not from worn bearings, it is a normal thing as the magnet is energized it rides on the inside armature of the drum and applies pressure of the brake shoe assembly towards the outside of the drum to apply brakes
A crimp butt connector with waterproof heat shrink will make a much more reliable connection. I've seen a bunch of bad electrical work from RV manufacturers, so I wouldn't use them as an example of good workmanship.
Great instructional and confidence building video. You even remind me to change my clothes. On a scale of 1- 10, if you're well prepared with paper towels, have a whole box of your 6 mil gloves on hand, Happy to know the names of all the parts. I want to video your video and watch the video while I replace my brakes. :) Thank you, it was clear and well done. Thanks for all the links below, you've done all the research, lowest prices, where you got great customer service, bonus.
Great video! Need your suggestion and opinion. I have a set of 4 new manually adjusting brakes and 4 new drums on my trailer. When I installed them I realized that both of my axels are covering brakes adjusting wholes.. There is no way to reach it with adjusting tool.. Any suggestions on how to work around it? Would I need to take off the wheels, adjust and put them back to try again?
Great video. I definitely give this a try next time my travel trailer needs a brake job. Since you used shrink wrap when rewiring the brakes, why didn't you also solder the wires?
![ผัวเถื่อน - ยูริ โตเกียวมิวสิค [ OFFICIAL MUSIC VIDEO ]](http://i.ytimg.com/vi/P08ORRVDGl8/mqdefault.jpg)
Ive been changing trailer brakes, bearings, axles for over 35 years .. this video is the real thing ..thanks for sharing ..well done
Looks straight forward,the only thing I would do differently would be to solder the 2 wires together before the shrink wrap. Thanks
One of the best instructors on YT
Highly instructional vid. Great job.
Thanks!
FANTASTIC INFORMATIVE VIDEO !
Perfect video. I noticed the trailor brake wires on a used 16 ft trailor I purchased have been cut. So, I'll be replacing mine soon. Thanks for the tutorial.
Great stuff. Many Super Thanks!
Many thanks!
The Lazy Lube system is the worst thing ever put on a travel trailer. Boat trailer okay. To much grease can cause churning in the bearings. Churning will generate heat. Trailer brake wiring must be connected with crimp on water tight connectors. Never use Scotch Locks. Bearings must have from .001 to .005 inches end play. Never preload a wheel bearing. All wear points on drum brakes must be lubricated at regular intervals.
I've had eazy lube on my Rv for 10 years, I always maintain it, PROPERLY, about 40,000km of trouble free use
Timken (tapered) bearings require preload. Better do some homework
@@davidjester7228 No preload on final adjustment. Wheel bearings must have end play. .001" to .005". Timken spec.
Not sure about bearing preload here. Also, pre greased bearings probably aren't Lucas Red so now 2 different greases going on.
Agreed. Cranking down on the bearing and calling it good is NOT the way to do it. Probably why dude had bearing issues. Preload your bearing, then loosen the nut...retighten finger tight. Done. I haul granite (12k+ lbs) and run 3000mi a week, never had a single issue with my bearings.
I’m surprised you don’t go through the process on how to properly torque the center nut. I can see someone inexperienced tightening the whack out of that nut and burning up there bearings.
what should the torque for the center nut be ? im currently replacing brakes on mine and when i unstalled it was so lose i didnt know if thats how they are supposed to be ?
@@AREA51_ATVSXS_PERFOMANCEjust snug , should spin freely but have no wobble left to right or up and down, usually can ve achieved by hand
They should also be readjusted after 3-500miles. @@LukeRT
I’ve always tightened the nut up as I’m spinning the drum in the opposite direction with a 1/2 drive ratchet. Snug it up tight then loosen about 1/4 turn, spin the drum again and retighten the nut. Back off about a 1/4 turn and install a new cotter key.
I do that by feel ...
Super good video...no dumb music, straight forward and great explanation...thank you.
Great video. Have you considered disc brakes? I am undecided if I continue with electric brakes or if I switch to disc.
Good video, but one thing I would add is the scoring on the inside of the drum is not from worn bearings, it is a normal thing as the magnet is energized it rides on the inside armature of the drum and applies pressure of the brake shoe assembly towards the outside of the drum to apply brakes
He had gouges not uniform look closer. Drums are ok to use.
Just heat shrink to hold the wires? 🥴
Thats how it was from the factory
A crimp butt connector with waterproof heat shrink will make a much more reliable connection. I've seen a bunch of bad electrical work from RV manufacturers, so I wouldn't use them as an example of good workmanship.
@thomasgriffin4714
Definitely a good butt connector followed by the shrink tubing
Usually how they come from factory if your lucky to get that much lol
Great instructional and confidence building video. You even remind me to change my clothes. On a scale of 1- 10, if you're well prepared with paper towels, have a whole box of your 6 mil gloves on hand, Happy to know the names of all the parts. I want to video your video and watch the video while I replace my brakes. :) Thank you, it was clear and well done. Thanks for all the links below, you've done all the research, lowest prices, where you got great customer service, bonus.
Don't snug & leave the bearing too tight!
Super Thanks gave me the confidence to do it myself.
Glad it was helpful for you! Its really not that bad of a project!
So. Maybe this is a dumb question. If you bought the drums/hubs pre-greased then why did they take so
much grease?
There is still air pockets after assembly. But it takes a lot less once assembled. I would say maybe a half tube per hub, if that
Great video!
Need your suggestion and opinion. I have a set of 4 new manually adjusting brakes and 4 new drums on my trailer. When I installed them I realized that both of my axels are covering brakes adjusting wholes.. There is no way to reach it with adjusting tool.. Any suggestions on how to work around it? Would I need to take off the wheels, adjust and put them back to try again?
Great video. I definitely give this a try next time my travel trailer needs a brake job. Since you used shrink wrap when rewiring the brakes, why didn't you also solder the wires?
You're a bad ass bro.. Appreciate you man..
Thank you!
What is the socket size for the spindle nut?
Just use a pair of slip joint pliers
Channel locks works just fine
Thank You!
Thank you!
How did you get the Drum Grease cap off?
Thank you
Thank you for this!
Thanks
Thank you!
Thanks!
Thank You! I'm glad you found the video helpful
Great video, thanks!
Thanks!