Just installed this intake system last night on my 2012 Forester XT and wanted to provide some feedback. Firstly, the video provides an excellent walkthrough of the process and I highly recommend it for those who don't want to go about this blind. The most difficult part was actually removing the old intake system as most of the parts were well adhered to their factory components (especially the hose leading to the engine). The cold air intake doesn't significantly alter the sound of the engine, but you absolutely hear the 'whooshing' sound. I find it very relaxing and reminds me of a spaceship accelerating. I'd love for my Forester to have the low rumble of the WRX, any suggestions on how best to achieve that effect (I presume expanding the exhaust piping diameter)?
Unequal length headers bro will do the trick and also expanding the diameter like you said so 3 Inch and that should give the classic Subaru deep tone (if you haven't already found this information out by now considering this message is two months old haha)
I like the design, but how would you know when the filter is dirty without removing that whole thing? An access panel on the top or back where you could check & service the filter would be ideal. 👌🏻
The gasket strips are a pain in the butt to apply. They're not very flexible in the sharp corners and putting it on the round hole where the filter connects to it's so time consuming. I had to cut mine now I'm thinking adding heat shield tape where I cut the gasket. I installed mine on a WRX STI hatchback 2014
It is something you have to be patient with and take your time installing. We have an install guide that should make it easier to understand how to apply it correctly.
2020- I have a 2011 project WRX hatchback.... I just put this on. It is a very clean design- I guess I check the filter when I change the oil by undoing everything I just did? (Correct?) Other than that- the video was a great tutorial.
Cobb does not have an OTS map for the GS intake so I would not recommend using that map on the GS intake. OTS maps are not meant for permanent use. They are only baseline maps to help the car and mod(s) run at a safe level; not max performance. A protune is the only way to guarantee compatibility between your car and the GS intake (or any mods) as well as increase performance safely; unless you can tune yourself.
The heat shield really does do a good job of keeping the heat isolated and out of the intake. The majority of the air comes from the wheel well and underside of the vehicle, far from the heat of the turbo, and downpipe.
Sumeet Kumar Unfortunately, you LGT guys have a slightly different MAF sensor, so this intake will not fit. With that said, we are working on an intake that will work on your car!
Adam Simpson Like OCTurboJoe said, a tune is highly recommended. There are COBB off the shelf maps that will work in the mean time, but to take full advantage of the intake and to ensure that you're vehicle is running safely, we do recommend a professional tune.
Good product but I see why you sped up putting on the heat shield. Your corners are too tight and that was one of the most obnoxious fucking things I've dont in my life. Jesus
Thank you so much for making videos for these I couldn’t find any
where's the sound at? why wouldn't you give us a sample of the intake suction???+
Just installed this intake system last night on my 2012 Forester XT and wanted to provide some feedback. Firstly, the video provides an excellent walkthrough of the process and I highly recommend it for those who don't want to go about this blind. The most difficult part was actually removing the old intake system as most of the parts were well adhered to their factory components (especially the hose leading to the engine). The cold air intake doesn't significantly alter the sound of the engine, but you absolutely hear the 'whooshing' sound. I find it very relaxing and reminds me of a spaceship accelerating. I'd love for my Forester to have the low rumble of the WRX, any suggestions on how best to achieve that effect (I presume expanding the exhaust piping diameter)?
Unequal length headers bro will do the trick and also expanding the diameter like you said so 3 Inch and that should give the classic Subaru deep tone (if you haven't already found this information out by now considering this message is two months old haha)
I like the design, but how would you know when the filter is dirty without removing that whole thing? An access panel on the top or back where you could check & service the filter would be ideal. 👌🏻
It doesn't take any effort to undo a couple fasteners and it doesnt take any brains to know that after every 10k or so miles to check it.
@@electroevolution5777 I love the enthusiasm but your 4 years too late 😂
came for the intake, stayed for the floozies. :D
that is a fine looking system i really like it over cobb's .but just not red,black would work great.
I like the looks of it! Very clean. Will you be posting an in car test drive vid in the near future?
The gasket strips are a pain in the butt to apply. They're not very flexible in the sharp corners and putting it on the round hole where the filter connects to it's so time consuming. I had to cut mine now I'm thinking adding heat shield tape where I cut the gasket. I installed mine on a WRX STI hatchback 2014
It is something you have to be patient with and take your time installing. We have an install guide that should make it easier to understand how to apply it correctly.
Do u have a part number for the reducing coupler? Mine is old and ripped
2020- I have a 2011 project WRX hatchback.... I just put this on. It is a very clean design- I guess I check the filter when I change the oil by undoing everything I just did? (Correct?)
Other than that- the video was a great tutorial.
I just got a 2011 wrx. Looking to get this, did you have to get a tune done?
I have installed the GrimmSpeed CAI on my 2012 WRX and observed a 16 awhp increase and a 13 awtq increase via a Protune on the Cobb Accessport.
+DownShiftCrew LX no problems after the pro tune?
+Jorge Flores No problems. It functions as intended and looks very good. I am tired of the loud sucking sounds though.
+DownShiftCrew LX thank you subibro
How would the ots maps on the Cobb accessport do with this ? What do you recommend besides a pro tune
Cobb does not have an OTS map for the GS intake so I would not recommend using that map on the GS intake.
OTS maps are not meant for permanent use. They are only baseline maps to help the car and mod(s) run at a safe level; not max performance.
A protune is the only way to guarantee compatibility between your car and the GS intake (or any mods) as well as increase performance safely; unless you can tune yourself.
Would this fit on a 2010 subaru liberty gt ?
Seems like it would be sucking in hot air? Even from underneath doesn't seem like it would be enough? Compared to the snorkel on the factory air box.
The heat shield really does do a good job of keeping the heat isolated and out of the intake. The majority of the air comes from the wheel well and underside of the vehicle, far from the heat of the turbo, and downpipe.
This clear your grimmspeed front mount innercooler?
Yes. It clears the GrimmSpeed front mount.
would this work in a 2012 non-turbo forester? mine is a 2.5x.
Great video and the intake looks great. Will this fit a 2015 STI?
+toyotrustPR We'll have one available shortly!
Will my base Impreza fit with this? it's a 2009 Impreza automatic
Unfortunately not, this would be for turbo models only,
Is the heat shield coated in ceramic or some sort of heat reflective material? How about the intake pipe?
DownShiftCrew LX It looks to be standard powdercoat. I'm sure heat reflective gold tape/material could be added.
Do I need a tune if I put this on my sti ?
Yes, a tune is highly suggested for our Cold air intakes
I'm looking to order this in a couple days. What cobb tune will work with this that will run safley.
James Smith did you evwr find out what Cobb tune you needed for this intake
will this be compatible to GVF model?
no plans for the STI 2015 versions?
+eapaaa Working on them now!
Will this work on the non wrx/sti 2009 imprezas too?
Yea, will it workk?
Hey guys, will this air intake fit on a 07-09 LGT?
Sumeet Kumar Unfortunately, you LGT guys have a slightly different MAF sensor, so this intake will not fit. With that said, we are working on an intake that will work on your car!
is it smog legal for ca
So no more airbag?
I'm not sure what you are referring to, but an installation of an intake does not affect the airbag system.
@@GrimmSpeed nvm I’m retarded
Will this intake fit on 2015+ STI?
+Cycotech Releasing in early 2016!
+GrimmSpeed any updates yet? Looking forward to a GS intake from u guys
is the air filter reusable
fittygrand It is reusable but it would need to be cleaned periodically.
Tune required??
As with any intake, it's highly recommended.
Adam Simpson Like OCTurboJoe said, a tune is highly recommended. There are COBB off the shelf maps that will work in the mean time, but to take full advantage of the intake and to ensure that you're vehicle is running safely, we do recommend a professional tune.
How about cleaning and oiling ?
non oil filter it's a dry filter
LOL at 'saliva will also work'
Good product but I see why you sped up putting on the heat shield. Your corners are too tight and that was one of the most obnoxious fucking things I've dont in my life. Jesus
will this fit on a 2010 Subaru Impreza Anesis non turbo?
Will this work with my 2011 subaru impreza 2.5i premium sedan?
No sir, it will not.