Hi there thanks for the video I’m currently working on a sprinter 2017 mod 313 cdi We have replaced the worn timing chain as It jumped We put the engine back together in the correct timing used the same injectors bled air from the fuel lines but we cannot get the engine to start it keeps cranking but no start however when we spray Starting Agent into the intake the engine briefly starts and runs as long as you keep spraying the agent into the intake I have Autotel Mk 808 Scener ( can this unit perform injector re-coding ?). We checked and confirmed that diesel injectors are corresponding to correct cylinders on the scanner. Common rail fuel pressure reaches 300 bar when cranking there’s no more air in the fuel lines all four cylinders are returning just under 300 psi compression but it seems to be that there is no fuel coming past any of the diesel injectors can it be possible that all four injectors have seized up shut Engine has done 465,000 km and it’s not displaying any more codes..? Any suggestion would be greatly appreciated Thanks
Hello there I hope this helps…I had this same issue we replaced the engine on a Sprinter 313 cdi due bent rod and of course we have to drain the fuel from the system we put everything back together as it should but didn’t wanted to start we found that the injectors got seized up shut we sent them to a shop to get them open and gave us instructions on how to bleed these Delphi injectors they’re pain in the rear but this how you bleed them when they’re completely dry 1st leave the injectors unplugged 2nd do not plug the return lines 3rd cycle the ignition about 5-6 times until there’s enough Diesel in the system 4th tighten the lines then lose them about 1/4 turn 5th have someone to crank the engine until you see Diesel pouring from the lose lines 6th close the lines 7th tell your buddy to crank the engine again until you see Diesel coming out of the injectors thru the return holes 8th plug the return lines 9th crank it again few times 10th plug the electrical connectors to the injectors, it should start Here is a video of these Injectors th-cam.com/video/ahqBYGmTLrA/w-d-xo.html
Again depends on your budget and what you need doing on the vans. If it’s just sprinters you deal with then I recommend getting dealership software as it does everything. Where as all these other machines only do a percentage of what dealership software does.
@@sadiagnostics no I didn’t coded the injector, today i tried to start the van, it started when i removed the camshaft sensor. May be it’s something off timing?
@@ShaheehAlJazeerra form my knowledge and experience coding is when you change a component so for example. Changing a EGR or any other component. However programming is when you need live data files. For example if your coding in engine or gearbox or headlight or any other part and your wanting latest file there is out there. To break it down further will talk about the gearbox, if you’ve bought a car in 2015 and you want to update the automatic gearbox then you would do programming this will put the latest file on the gearbox. These files are direct from dealer. It’s basically trial and error and they do this every year and dealers get many recalls and and damaged parts due to faulty files uploaded especially on the engine. Sometimes the file they use to run the injectors cylinders etc. they then come out with a new file and that’s where you programme the new file. This will also stamp the date when you programme it. Coding is different that will just be a replacement part and you code it to the car to say you’re had a new part fitted but not updated software…
My car has a check engine light , fuel injector control module, a mechanic scan it and said some one replaced the injector and didn’t enter the values , he said they all say 0
Injectores job have been done on my Mercedes and the car crank but don’t start , saw your video and went to check , and saw that he put the injector code from injector number 3 on the on the injector 4 . Now I try to change but wasn’t working , the Maxine was failing to do the programming what is your advice ?? Thanks will help a lot My car is Mercedes E class 220 bluetec 2014
Hi....can you maybe help me.. i changed my injectors on ml280 w164 (the car worked before the change but had lots of white smoke and fuel consumption was crazy) so i then coded the injectors and the car wont start.. it cranks but wont start.. i get code 2211-1 and 2242-1 which i didnt have before.. fuel pressure is good...idk what to do anymore 😂 can you help?
With my mk906 pro i could not get in to the engine... Didn't show a single hot function and kept saying it was a gasoline car while it's a diesel. I have send the computer back. What a waste!
Was really looking for a video on what to look for with injectors using a scan tool, but good anyway
Thanks for the feedback
Hi there thanks for the video I’m currently working on a sprinter 2017 mod 313 cdi
We have replaced the worn timing chain as It jumped We put the engine back together in the correct timing used the same injectors bled air from the fuel lines but we cannot get the engine to start it keeps cranking but no start however when we spray
Starting Agent into the intake the engine briefly starts and runs as long as you keep spraying the agent into the intake
I have Autotel Mk 808 Scener ( can this unit perform injector re-coding ?). We checked and confirmed that diesel injectors are corresponding to correct cylinders on the scanner.
Common rail fuel pressure reaches 300 bar when cranking there’s no more air in the fuel lines all four cylinders are returning just under 300 psi compression but it seems to be that there is no fuel coming past any of the diesel injectors can it be possible that all four injectors have seized up shut
Engine has done 465,000 km and it’s not displaying any more codes..?
Any suggestion would be greatly appreciated
Thanks
Hi sorry I can’t really say much it could be anything really, cam shaft sensor etc… do live data and see if anything is coming up
Hi did I have the same exact problem.
Did u solved the problem ??
Thanks
@@93mrmm also have the same problem, can start it for 3 days, did you fix it maybe?
Did you find out what’s wrong I have same issue thanks
Hello there I hope this helps…I had this same issue we replaced the engine on a Sprinter 313 cdi due bent rod and of course we have to drain the fuel from the system we put everything back together as it should but didn’t wanted to start we found that the injectors got seized up shut we sent them to a shop to get them open and gave us instructions on how to bleed these Delphi injectors they’re pain in the rear but this how you bleed them when they’re completely dry 1st leave the injectors unplugged 2nd do not plug the return lines 3rd cycle the ignition about 5-6 times until there’s enough Diesel in the system 4th tighten the lines then lose them about 1/4 turn 5th have someone to crank the engine until you see Diesel pouring from the lose lines 6th close the lines 7th tell your buddy to crank the engine again until you see Diesel coming out of the injectors thru the return holes 8th plug the return lines 9th crank it again few times 10th plug the electrical connectors to the injectors, it should start
Here is a video of these Injectors
th-cam.com/video/ahqBYGmTLrA/w-d-xo.html
If you mix up injectors by mistake will they still code correctly ?
If injectors have become mixed how does one find their correct allocation
@@aqibfreed4672 no they won’t code, it will just bounce back and says incorrect
Awesome thanks
@@Bonnici94 thank you for the feedback
Great video what’s the best Autel to use on sprinter vans
@@redmonster5 thanks it Autel Maxisys ms908s pro
Again depends on your budget and what you need doing on the vans. If it’s just sprinters you deal with then I recommend getting dealership software as it does everything. Where as all these other machines only do a percentage of what dealership software does.
Great video.So can MaxiSys Pro do component protection in VAG groups?
They are not the best, your better buying live vcds.
Good job
Thank you
Hi can you help me my sprinter is not starting after engine change
@@JatinderSingh-jj5xi hi have you coded the new engine in also is the immobiliser all paired up…
@@sadiagnostics no I didn’t coded the injector, today i tried to start the van, it started when i removed the camshaft sensor. May be it’s something off timing?
@@JatinderSingh-jj5xi yes sounds like camshaft for full scan and see what comes back…
BEAUTIFUL PLZ COUD YOU EXPLAIN WHAT IS THE DIFFERENCE BETWEEN CODING AND PROGRAMMING AS WELL AS SOFTWARE TO MOUDLE?
THX REGARDS A LEARNER.
@@ShaheehAlJazeerra form my knowledge and experience coding is when you change a component so for example. Changing a EGR or any other component. However programming is when you need live data files. For example if your coding in engine or gearbox or headlight or any other part and your wanting latest file there is out there. To break it down further will talk about the gearbox, if you’ve bought a car in 2015 and you want to update the automatic gearbox then you would do programming this will put the latest file on the gearbox. These files are direct from dealer. It’s basically trial and error and they do this every year and dealers get many recalls and and damaged parts due to faulty files uploaded especially on the engine. Sometimes the file they use to run the injectors cylinders etc. they then come out with a new file and that’s where you programme the new file. This will also stamp the date when you programme it. Coding is different that will just be a replacement part and you code it to the car to say you’re had a new part fitted but not updated software…
@@ShaheehAlJazeerra sorry for late reply I’ve had tonnes of comment and messages
Always great content thanks 🙏
Thank you 🙏
@@sadiagnostics i have the same problem with mu 2014 sprinter..i need ur service
Is it the same thing for 2013 mercedes cls550
No it’s different with Petrol cars…
My car has a check engine light , fuel injector control module, a mechanic scan it and said some one replaced the injector and didn’t enter the values , he said they all say 0
C250 2012 needs coding new Injectors too or no ?
@@chrisisho2557 yes any injector changed will require coding
If you use easy start spray it would start ???
@@edmilsonpinto4619 I doubt it cause it’s all to do with software rather than trying to start it manually
Injectores job have been done on my Mercedes and the car crank but don’t start , saw your video and went to check , and saw that he put the injector code from injector number 3 on the on the injector 4 .
Now I try to change but wasn’t working , the Maxine was failing to do the programming what is your advice ??
Thanks will help a lot
My car is Mercedes E class 220 bluetec 2014
Don’t know if was doing wrong way , the Maxine that I was using it calls Nukar
@@edmilsonpinto4619 sorry for late reply it might be that the injector is also faulty hence why it’s not allowing you to code it in…
Hi....can you maybe help me.. i changed my injectors on ml280 w164 (the car worked before the change but had lots of white smoke and fuel consumption was crazy) so i then coded the injectors and the car wont start.. it cranks but wont start.. i get code 2211-1 and 2242-1 which i didnt have before.. fuel pressure is good...idk what to do anymore 😂 can you help?
Great information boss waht is name this I mean autel waht model and number
Thanks it’s Autel Maxisys MS908s pro
does this apply to w638 vito ? have replaced 4x injectors - will not start on key but can roll start it and runs fine.
Yes all Mercedes are same.
@@sadiagnostics thanks for the reply, its weird that i can get it running from a roll start and it runs mint, just never starts under key
@@joshrulz8p yeh that’s like first I’ve heard but hopefully you’ll get it sorted.
With my mk906 pro i could not get in to the engine... Didn't show a single hot function and kept saying it was a gasoline car while it's a diesel. I have send the computer back. What a waste!
And why doesn't Autel send a user manual with the computer!!?? Unbelievable
Love you sir
Hello sir..my sprinter has the same problem,can i get ur contact
great!
What Autel system is this?
Ms908s pro
👋
One video uploade redar